- mvs.4 uses nested '.Bl' tags which appears to confuse man2hwnotes.pl
for hardware note generation
- mps.4 also breaks the build, but I haven't yet identified why
built with -Wundef, as opposed to world.
Additionally, cdefs.h tends to not use indentation for preprocessor
directives, so remove that too.
Pointy hat to: me
This should get the correct memory size even if a 32-bit image is running
on a machine with > 4GB of memory. This can be useful is using a 32-bit
installer on a machine which will eventually run a 64-bit image.
Reviewed by: kmoore
- Improved locking and destruction process to fix crashes.
- Improved "automatic" configuration method to make it consistent and safe
by reading metadata back from all specified paths after writing to one.
- Added provider size check to reduce chance of ordering conflict with
other GEOM classes.
- Added "manual" configuration method without using on-disk metadata.
- Added "add" and "remove" commands to allow manage paths manually.
- Failed paths are no longer dropped from geom, but only marked as FAIL
and excluded from I/O operations.
- Automatically restore failed paths when all others paths are marked
as failed, for example, because of device-caused (not transport) errors.
- Added "fail" and "restore" commands to manually control FAIL flag.
- geom is now destroyed on last path disconnection.
- Added optional Active/Active mode support. Unlike Active/Passive
mode, load evenly distributed between all working paths. If supported by
the device, it allows to significantly improve performance, utilizing
bandwidth of all paths. It is controlled by -A option during creation.
Disabled by default now.
- Improved `status` and `list` commands output.
Sponsored by: iXsystems, inc.
MFC after: 1 month
cp2103 usb-to-serial chip.
- This patch also makes the line status polling asynchronous, to reduce
the time needed to change the GPIO pins.
Submitted by: JD Louw
MFC after: 1 week
- Make it easier to port the USB code to other platforms by only using
one set of memory functions for clearing and copying memory. None of
the memory copies are overlapping. This means using bcopy() is not
required.
- Fix a compile warning when USB_HAVE_BUSDMA=0
- Add missing semicolon in avr32dci.
- Update some comments.
MFC after: 1 week
after its installation. This removal may be accidental and can
prevent the default route from being installed in the future if
the associated default router has the best preference. The cause
is the lack of status update in the default router on the state
of its route installation in the kernel FIB. This patch fixes
the described problem.
Reviewed by: hrs, discussed with hrs
MFC after: 5 days
if_alloctype was used to store the origional interface type. Take
advantage of this change by removing all existing uses of if_free_type()
in favor of if_free().
MFC after: 1 Month
- fix other errors introduced when committing r226436
- add 'function' to a sentence where it makes sense
Submitted by: delphij
Submitted by: dougb
Submitted by: jhb
Approved by: dougb
Approved by: jhb
change the on-disk format in an incompatible way. Without this change,
msdosfs created on FreeBSD/arm would not be mountable.
PR: bin/162486
Submitted by: Ian Lepore <freebsd damnhippie dyndns org>
Reported by: Mattia Rossi <mrossi at swin.edu.au>
MFC after: 3 days
the length of frame should be treated as multiple of 4. Actual
frame length is set in the TX header. The TX header position
should be aligned on 4 byte boundary and actual frame start
position should be aligned on 4 byte boundary as well. This means
we need 4(TX header length) + 3(frame length fixup) additional free
space in TX buffer in addition to actual frame length.
Make sure TX handler check these additional bytes.
ae_tx_avail_size() returns actual free space in TX buffer to ease
the calculation of available TX buffer space in caller. While I'm
here, replace magic number to appropriate sizeof operator to
enhance readability.
This change should fix controller lockup issue happened under
certain conditions but it still does not fix watchdog timeout. It
seems the watchdog timeout is side-effect of TxS and TxD
mismatches. The root cause of TxD/TxD mismatch is not known yet but
it looks like silicon bug. I guess driver may have to reinitialize
controller whenever it sees TxS and TxD mismatches but leave it as
it was at this moment.
PR: kern/145918
to match native struct timespec ABI on __LP32__.
This change is a prerequisite for upcoming futimens()/utimensat() in whose
implementations it is assumed that timespec32 can take a negative value.
MFC after: 1 week
results in the HAL being built without HAL debugging/diagnostic support,
the module building process needs to be somehow taught to not build AR5416+
NICs if AH_SUPPORT_AR5416 isn't defined in opt_ah.h .
certain instructions in a function prologue or epilogue. DTrace has a
hook into the invalid opcode fault handler that checks whether the fault
was due to an probe and if so, runs the DTrace magic.
Upon returning from an invalid opcode fault caused by a probe, DTrace must
emulate the instruction that was replaced with the invalid opcode and then
return control to the instruction following the invalid opcode.
There were a pair of related bugs in the emulation for the leave
instruction. The leave instruction is used to pop off a stack frame prior
to returning from a function. The emulation for this instruction must
move the trap frame for the invalid opcode fault down the stack to the
bottom of the stack frame that is being removed, and then execute an iret.
At two points in this process, the emulation code was storing values above
the current value of the stack pointer. This opened up a window in which
if we were two take an interrupt, the trap frame for the interrupt would
overwrite the values stored on the stack, causing the system to panic
later.
The first bug was that at one point the emulation code saves the new value
for $esp above the current stack pointer value. The fix is to save this
value instead inside of the original trap frame. At this point we do
not need the original trap frame so this is safe.
The second bug is that when the emulate code loads $esp from the stack, it
points part-way through the new trap frame instead of at its beginning.
The emulation code adjusts the stack pointer to the correct value
immediately afterwards, but this still leaves a one instruction window in
which an interrupt would corrupt this trap frame. Fix this by adjusting
the stack frame value before loading it into $esp.
This fixes panics in invop_leave on i386 when using fbt return probes.
Reviewed by: rpaulo, attilio
MFC after: 1 week
object files corresponding to source files that had the compile-with
option set in conf/files. This means that any fbt probes for functions
in that object file would not have correct argument types.
The fix is to run ctfconvert on any target file that does not have the
no-obj option set in files.
PR: bin/160275
Reported by: Paul Ambrose (ambrosehua AT gmail DOT com)
MFC after: 1 week
doesn't have ${WORLDTMP}/usr/bin in its PATH, if you build world with
CC=clang, tblgen tools from /usr/bin will be used instead of the ones
built under ${WORLDTMP}. This can lead to various errors, especially if
you upgrade from an older clang.
Note that building world with gcc would not experience these problems,
because it only uses the tblgen tools in the world stage, where PATH
does contain ${WORLDTMP}/usr/bin.
Pointy hat to: dim
