Use remaining number of DMA segment instead of maximum number in mapping
when checking space for one more TSO segment packet.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Sync endif comment with conditional.
BOOTROM and SIENA_BOOTROM are the same, but highlight that it is Siena.
Restore commented out assertion.
Sync comments with out-of-tree driver.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Before the common code had hard coded limits on the IDs RXQs and TXQs could
be created with which were suited for the Windows driver with VMQ, and so
would prevent queues with IDs greater than or equal to 259 (for TXQs) or 768
(for RXQs) from being created. This change allows the limits to be set in
efsys.h, so that all 1024 queues can be created during new manftest tests.
Also, the descriptor cache sizes were also hard coded to values suited to
the smaller queue counts, and so it was necessary to make them configurable
as well.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Caught when efx_filter_init() failed and called efx_filter_fini() in the
teardown path.
Submitted by: Andrew Lee <alee at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Previously the driver's view was the expected outcome of any
reconfiguration even if that reconfiguration failed.
Submitted by: Ben Horgan
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
We must not enable RX queues with random parameters when they are
mapped into a VF with an untrusted driver. It's probably not a good
idea to do this anyway, so take this bit out of the table test masks.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Otherwise when processing finally comes to efx_tx_qdesc_post() it could
be insufficient space between reaped and added to post pending
descriptors.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
efx_ev_mcdi() does not assert or check that all event handlers it
calls are non-null. Add assertions at the top for all required
event handlers, as some events (in the case of this bug, monitor
events) are rare.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Use nitem() to get number of array elements.
Remove unused define.
Use TAB to indent.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
TCP header is fragmented in the case of VLAN tagged IPv6 traffic without
HW VLAN tagging.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
will be used with arm64 to find which cpus to enable, and could also be
used with 32-bit arm and mips for the same purpose.
Differential Revision: https://reviews.freebsd.org/D1825
Sponsored by: The FreeBSD Foundation
This will be needed by arm64 to find the value to pass to the psci (Power
State Coordination Interface) driver, among other things, used to enable
cores.
Differential Revision: https://reviews.freebsd.org/D1824
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
properly.
If there is garbage in the flags field, it can sometimes include a
set CDAI_FLAG_STORE flag, which may cause either an error or
perhaps result in overwriting the field that was intended to be
read.
sys/cam/cam_ccb.h:
Add a new flag to the XPT_DEV_ADVINFO CCB, CDAI_FLAG_NONE,
that callers can use to set the flags field when no store
is desired.
sys/cam/scsi/scsi_enc_ses.c:
In ses_setphyspath_callback(), explicitly set the
XPT_DEV_ADVINFO flags to CDAI_FLAG_NONE when fetching the
physical path information. Instead of ORing in the
CDAI_FLAG_STORE flag when storing the physical path, set
the flags field to CDAI_FLAG_STORE.
sys/cam/scsi/scsi_sa.c:
Set the XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE when
fetching extended inquiry information.
sys/cam/scsi/scsi_da.c:
When storing extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_STORE instead of
ORing it into a field that isn't initialized.
sys/dev/mpr/mpr_sas.c,
sys/dev/mps/mps_sas.c:
When fetching extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE instead of
setting it to 0.
sbin/camcontrol/camcontrol.c:
When fetching a device ID, set the XPT_DEV_ADVINFO flags
field to CDAI_FLAG_NONE instead of 0.
sys/sys/param.h:
Bump __FreeBSD_version to 1100061 for the new XPT_DEV_ADVINFO
CCB flag, CDAI_FLAG_NONE.
Sponsored by: Spectra Logic
MFC after: 1 week
temporary buffer when remaining space is not enough to hold
a whole block.
- yarrow.c: add a comment that we intend to change the code and remove
memcpy's in the future. (*)
Requested by: markm (*)
Reviewed by: markm
Approved by: so (self)
Allocate the minimum or maximum response length for GET_BOARD_CFG as
appropriate. When looking up firmware subtypes by partition ID,
check the ID against the actual response length.
Merge of the patch made by Ben Hutchings in 2011.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Mainly to unify with similar member for transmit and receive queues.
It will be used in the future for resources allocation processing.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It avoids access to m_pkthdr when TSO packet is started and also makes
tso_start_new_packet() function smaller.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
sometimes. It will power up wrong and identify itself badly:
cardbus0: <network, ethernet> at device 0.0 (no driver attached)
cardbus0: <simple comms, UART> at device 0.1 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.2 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.3 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.4 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.5 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.6 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.7 (no driver attached)
All the higher numbered functions (.2 and above) have a config space
of all 0's. This smells a bit like a special debug mode, but the
current atheros driver doesn't cope. It is unclear if this card is
just a flake, or if we're doing something wrong in the power-up
sequence.
Put a work around into the code that tests for this rather unusual
condition. If we power a CardBus device up, and the device says it is
multi-function, and any of the functions have a 0 device ID, try the
power-up sequence again.
randomdev_init_reader to change read_random over to the newly installed
adaptor was missed. This means both read_random and arc4random (seeded
from read_random) were not returning very random data. This also
effects userland arc4random as it is seeded from kernel arc4random.
The random devices are uneffected and have returned good randomness
since the change.
All keys generated with a kernel of r273872 must be regenerated with
a kernel with this patch. Keys generated may be predictable.
Remove the warning as log is too early to print anything, and it would
always get printed due to early use of arc4random...
Reviewed by: delphij, markm
Approved by: so (delphij)
Highlights:
- Multiple verbs API updates
- Support for RoCE, RDMA over ethernet
All hardware drivers depending on the common infiniband stack has been
updated aswell.
Discussed with: np @
Sponsored by: Mellanox Technologies
MFC after: 1 month
interrupt status bit. According to the UHCI controller specification
the host controller halted interrupt is non-maskable.
PR: 156596
Tested by: adrian @
MFC after: 1 week
identifies the tested condition for _PRT as "BYTE value of 0", so the
remaining part of the conditionals is sufficient.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
This is to avoid a witness warning about a waiting memory allocation in
the evnt hanlder registration code.
Reported by: markj
MFC after: 3 days
X-MFC with: r277795
