It is available mostly in A10 devices like Hackberry, Marsboard,
Mele A1000, A2000, A100 HTPC, cubieboard1 and A20 device
like cubieboard2.
TX performance can be improved using both channels 0 and 1.
RX performance is poor and needs improvement with the assistance of
external DMA controller in case there is bulk TCP receiver.
Reviewed by: yongari@
Approved by: stas (mentor)
we've been using was actually just spinning due to ARM having redefined
the old 'wait for interrupt' operation via the system coprocessor as a nop
and replacing it with a WFI instruction.
code can supply a better implementation. A SoC with variable CPU frequency
is likely to use a fixed-frequency timer for DELAY() (but still use the
mpcore private timers as eventtimers).
Also remove spaces from the eventtimer and timecounter names.
implementation in arm/machdep.c. Most arm platforms either don't need to
do anything, or just need to call the standard eventtimer init routines.
A generic implementation that does that is now provided via weak linkage.
Any platform that needs to do something different can provide a its own
implementation to override the generic one.
- Don't use spaces or dots in the eventtimer or timecounter names.
They turn into sysctl node names, and it's just confusing.
- Use comparator #3 instead of #1 for one-shot events. There's an
extra 1-cycle penalty in the hardware for accessing the registers
for comparator 1, no point in paying that penalty.
- Lower the quality of the eventtimer from 1000 to 800, because the
device can't support PERCPU timers and some other device in the system
may be able to provide that.
Quartz is a tiny module utilized Freescale VF6xx
system-on-chip and development kit produced by
Device Solutions.
Quartz is available in a form of LGA (38x38x2mm)
or as a module with high-density connectors.
Sponsored by: Device Solutions
the Bufferable bit in the PDE entries of the secondary processor startup
pagetables.
The caches really need to be invalidated even earlier than this, but this
is a big step in the right direction. The invalidate needs to happen
before the MMU is enabled, which means it has to be called from asm code
that's running with physical addressing. Fixing that will be handled in
a future change.
implementations for each of the chips we support. Most chips up through
armv6 can use the armv4 implementation which has a single coprocessor
opcode for this operation. The rather more complex armv7 implementation
comes from netbsd.
While this is technically more correct, I don't think it much matters,
because the only thing in the tree that calls cpu_flush_dcache() is md(4)
and I'm > 99% sure it's bogus that it does so; md has no ability to do
anything that can perturb data cache coherency.
it into a bunch of different .c files. Remove declarations for the unused
mptramp() function from everywhere except AramadaXP (and I think it's
really not used there either, because the code that references it appears
to be insanely does-nothing in nature).
WANDBOARD.common config, but with the freescale-specific optons and devices
all together at the bottom now. In addition to reformatting and shuffling
lines around, two new options are added because they're now known to work,
VFP and FREEBSD_BOOT_LOADER.
This config does not include any static DTB, it requires that u-boot
provide a DTB (or a custom kernel config can compile one in).
This will supercede all the existing WANDBOARD* configs, but those will
be left around for a while to help people transition their customized
configs to include this new one instead.
The temperature monitor device is enabled to sample the die temperature at
16hz. The temperature is published via sysctl. A callout routine at 10hz
monitors the temperature and throttles back the cpu if the temperature
goes over a user-settable throttle point (by default 10C less than the
critical high-point temperature for the chip). The hardware is supposed
to be able to deliver an interrupt when the temperature exceeds a settable
limit, but the interrupt never arrives so for now a callout does the job.
At attach time we read the maximum cpu frequency the chip is allowed to run
at and the cpu is set to run at that speed. It's reported at attach time.
A sysctl variable reports the current speed when queried.
New sysctl values:
dev.imx6_anatop.0.cpu_mhz: 984
dev.imx6_anatop.0.temperature: 37.9C
dev.imx6_anatop.0.throttle_temperature: 95.0C
Steven Lawrance did the initial heavy lifting on this, but I changed
enough stuff that I'm the one to blame if anything breaks.
Submitted by: Steven Lawrance <stl@koffein.net>
and CAMBRIA boards that does not use loader to load the kernel. This
is basically how it was done for i386. This way tunables can also be
set. For example in config file:
env "/conf/AVILA.env"
And in AVILA.env:
vfs.unmapped_buf_allowed=0
MFC after: 2 weeks
is attached, by establishing a temporary mapping of the registers when
necessary. This is a temporary measure to keep progress moving; in the
long run we need better control over the order in which devices attach
(better than "the order they appear in the fdt dts source").
Attempt to demote the superpage if trying to pmap_enter() on
one. Panic only when the particular superpage should
no longer exist for that pmap and address.
