The i++ loop from 1..1000 is too small on very fast machines like
PII 450 MHz. Increasing the loop from 1..100000 lets the machine
access PHY. After this patch it's possible to use a SMC PCI card
on a HP Kayak XA series PC Workstation. Workaround until this fix
was to enable debugging in the driver (#define EPIC_DEBUG 1).
Without that patch you get an undefined state:
while true
do
ifconfig -a | grep status:
done
The status messages flaps between twwo values, but not
"connected".
Obtained from: Ustimenko Semen <semen@iclub.nsu.ru>
determine IRQ and DRQ information.
Fix a bug that would cause us to attempt to retrieve extended sync
rate information on cards/firmware revs that do not support that command.
config info. On early revision cards (742a), the EISA register space,
other than the location used to determine the address of the card's main
command ports, is write only.
This code is backwards compatible with the older "microkernel" PLL, but
allows ntpd v4 to use nanosecond resolution. Many other improvements.
PPS_SYNC and hardpps() are NOT supported yet.
Also, unbreak the breakage introduced at the last revision of module.c.
This changes the semantics of mod_searchfile() (and mod_searchmodule())
to make the caller's responsibility freeing the buffer returned. This
is different from other functions in loader's code, and was done as a
fix for kern/9631. If someone wants to revert this to the original
behavior, don't forget to fix kern/9631 in another way.
This should also fix bin/10462, which was introduced as a result of the
first try at kern/9631 (module.c last revision).
PR: bin/10462
Submitted by: Takanori Saneto <sanewo@ba2.so-net.ne.jp>
trouble with tagged queueing as the 6.5 gig version.
So, I've added a quirk entry for it to limit it to two outstanding
transactions at a time, just like the 6.5G version. While I'm at it, add a
quirk for the 9G version of the drive, since it most likely has the same
problem.
Submitted by: Jeremy Lea <reg@shale.csir.co.za>
reports on those most welcome!
Fixed problems:
Hang on probe on "fantom" devices.
The probe now use a timeout to avoid hangs if no interrupt
is recevied.
There has also been more general code clenaups, and some reorgs.
lock) until it actually needs to modify the vm_map.
Note: it is legal to modify vm_map::hint without holding a write lock.
Submitted by: "Richard Seaman, Jr." <dick@tar.com> with minor changes
by myself.
unregister them after sysuninits when unloading.
* Add code to vfs_register() to set the oid number of vfs sysctls to
the type number of the filesystem.
Reviewed by: bde
type may become necessary soon. :)
Also add a couple of additional macros that NetBSD has which we don't.
Nothing in FreeBSD uses these (yet) so adding them in shouldn't hurt
anything.
to manage their own memory. Tested on my machine (make buildworld).
I've made analogous changes on the alpha, but don't have a machine
to test.
Not-objected-to by: dg, gibbs
connection.
Clean up support for devices featuring the multiple target SCSI ID feature.
On aic7890/91/96/97 chips, we can now assume the target role on multiple
target ids simultaneously. Although these chips also have sufficient
instruction space to hold to support the initiator and target role at the
same time, the initiator role is currently disabled as it will conflict
(chip design restriction) with the multi-tid feature. I'll probably add
a nob to enable the initiator (there-by disabling multi-tid) some time
in the future.
Return queue full or busy, depending on the tagged nature of the incoming
request, if our command input queue fills up in host memeory.
Deal with accept target I/O resource shortages.
If we get an underrun on a transaction that wasn't supposed to transmit
any data, don't attempt to print out the S/G list. The code would
run until hitting a non-present page. (oops)
emulator so that instances can be dynamically added and removed from the
system.
Properly reference count peripheral instances so they are cleaned up when
destroyed by the control device.
Set a timeout for test unit ready commands. Before it was uninitialized
and could cause us to drop off the bus when no real timeout had occurred.
caused by temporary EDT allocations performed by controller drivers in
their interrupt routiens.
Reference count bus entries in the EDT in preparation for support for
dynamic controller arrival and departure.
Have children of the EDT hold references to their parents.
Correct routing of the XPT_IMMED_NOTIFY ccb type for use in
target mode applications.
Fix a few cases where the generation count for EDT data members was
not being updated when a modification occurred.
splcam() problem Noticed by: Tor Egge <tegge@FreeBSD.org>
probably always be 16 bits if they exist at all, and fusword() and
susword() are only used in i386 code, so there aren't any portability
functions with them.
numbers as chars or use bogus casts in an attempt to unmisrepresnt
them. In top, don't assume that 0xff is the only negative cpu
number when cpu numbers are (mis)represented.
include of <sys/queue.h> in the !KERNEL case. The prerequisites
for <ufs/ufs/quota.h> were broken in Lite2 by converting some of
the kernel declarations to use queue macros without including
<sys/queue.h>. <sys/queue.h> was included in applications in
/usr/src instead. We polluted this file instead of merging the
changes in the applications.
Include <sys/queue.h> in the KERNEL case, and forward-declare all
structs that are used in prototypes, so that this file is almost
self-sufficient even in the kernel.
Obtained from: mostly from NetBSD
interrupts are enabled, this kills the last "unwanted interrupts"
(and there is no ugly hacks like in the old driver to avoid them).
COmmand interrupt devices are now supported, this applies mostly
to older CDROM's and apparently also the ZIP.
Fixed problems:
Number of total sectors wrong on some older drives.
Fixed by not using the LBA size unless we know its valid.
There has also been more general code clenaups, some reorgs also.
so that non-sloppy applications can call it without using disgusting
casts to avoid warnings. The 4th arg is sort of varargs -- it must
sometimes represent a filename, sometimes a struct pointer, and is
sometimes unused. The arg type is still caddr_t in the kernel.
Obtained from: mostly from NetBSD
a TLB invalidation optimization that won't work given the
limitations of our current SMP support.
This patch should be applied to -stable ASAP.
Thanks to John Capo <jc@irbs.com>,
Steve Kargl <sgk@troutmask.apl.washington.edu>, and
Chuck Robey <chuckr@mat.net>
for testing.
Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver.
Fixed problems:
Dont use more sectors/intr than the drive supports.
Fix announce of > 8.4G disks.
Dont call ad_interrupt/ad_transfer when no disks config'd.
Use the right page# for CDR write mode params.
Fix breakage when no PCI support in kernel.
Implement DEVFS stuff.
General code clenaup.
Higher numbers led to smaller quanta.
In discussion with BDE, change this parameter to be in uSecs
to make it machine independent,
and limit it to non zero multiples of 'tick' (rounding down).
Also make the variabel globally available so that the present function that
returns its value (used for posix scheduling I believe) can go away.
Submitted by: Bruce Evans <bde@freebsd.org>
the read lock around the subyte operations in mincore. After the lock is
reacquired, use the map's timestamp to determine if we need to restart
the scan.
This produced races resulting in panics and filesystem corruptions
under some circumstances.
Reviewed by: luoqi chen <luoqi@freebsd.org>
Reviewed by: Kirk McKusick <mckusick@mckusick.com>
Submitted by: Matt Dillon <dillon@freebsd.org>
Change VINUM_SAVECONFIG: it now requires a parameter. 0 means
"configuration updates are finished, please save", and 1 means "please
just save the config". This second meaning is invoked by the new
"saveconfig" command to vinum(8).
Recognize "referenced" drives by the lack of a slash in the device
name, not by a NUL character.
vinum_scandisk: return error indication (ENOENT if we can't find any
vinum drive, otherwise 0).
VINUM_SAVECONFIG: change parameters.
Don't save config while we're reading it from disk.
Change the way we handle the daemon: if we can't communicate with it
for 1 second (which is possible), start a new one. The daemon saves
its pid in daemonpid; on each iteration of the main loop the daemon
checks whether it's still in favour. If not, it silently exits.
Also, when trying to communicate with the daemon, check daemonpid
first. If it's set to 0, don't even try.
Rename the VF_KERNELOP to VF_DISKCONFIG and checkkernel () to
checkdiskconfig (), which better describes their function.
Disable configuration updates if we have an error reading in the
configuration. This stops a "shoot-in-foot" problem where a mistake
can cause the configuration to be obliterated.
Tidy up some messages, which included superfluous \ns.
Recognize RAID-5 configuration information even in the non-RAID-5
version. This fixes shoot-in-foot problems where starting the wrong
version of vinum would kill RAID-5 plexes.
Recognize drives that have been referenced, but for which no physical
location is known. This is part of a modification which will
ultimately allow incrementally reading configurations. Such drives
will have a device name "unknown".
New function return_drive_space () returns space to a drive.
Previously this was part of free_sd ().
give_sd_to_drive: don't do it if the subdisk needs more space than the
drive has available.
config_sd: if reading config from disk, accept plex offset, drive
offset and length specs of -1 to indicate error conditions.
parse_config: return ENOENT if the "read" command doesn't find any
drives.
remove_sd_entry: don't do it, even by force, if it's open.
If the size of a striped or RAID-5 plex is not an integral multiple of
the stripe size, trim the size until it is.
reinstate update_volume_config, which had atrophied, to recalculate
the size of a volume if a plex has shrunk due to stripe size
considerations.
vinumattach: Zero out tables after allocating them
Modify procedure at unload: if a vinum(8) has the superdev open, don't
close down. If only the daemon has it open, send the daemon a stop
request and wait for it to close the superdev, then unload.
In order to do this, create a second superdev which is opened by the
daemon. The open and close routines set a different bit in
vinum_conf.flags; otherwise the treatment is identical.
Remove opencount field in vol structure; replace by a flag bit, since
we can't count the number of opens.
Remove dead LKM grunge.
lives in ext2_vnops.c for ext2fs. Also remove cast from comparision.
Bruce pointed out that it was bogus since we'd force a signed
comparision when we really wanted an unsigned comparison.
to write all the dirty blocks. If some of those blocks have dependencies,
they will be remarked dirty when the I/O completes. On systems with
really fast I/O systems, it is possible to get in an infinite loop trying
to flush the buffers, because the I/O finishes before we can get all the
dirty buffers off the v_dirtyblkhd list and into the I/O queue. (The
previous algorithm looped over the v_dirtyblkhd list writing out buffers
until the list emptied.) So, now we mark each buffer that we try to
write so that we can distinguish the ones that are being remarked dirty
from those that we have not yet tried to flush. Once we have tried to
push every buffer once, we then push any associated metadata that is
causing the remaining buffers to be redirtied.
Submitted by: Matthew Dillon <dillon@apollo.backplane.com>
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
tulip_addr_filter() on SIOCSIFFLAGS, and was nuking the IFF_ALLMULTI
on entering tulip_addr_filter(). As a result it was impossible to run
a multicast router on a machine with a "de" interface.
already defined. This allows for cross building to work because we
need to lie to make to tell it to use the target names rather than the
host names.
This should have no effect on either architecture. I've confirmed
that the intel build by make buildworld's for the past 3 months.
catch a T4000s)
+ Set *some* kind of error at EOM if we're in fixed mode and have pending errs.
Do not clear the ERR_PENDING bit if more buffers are queued.
+ Release the start_ccb in this case also, else we hang forever on rewinding.
+ Any kind of error for load to BOT in samount should then cause an attempt
to use REWIND to come back to BOT. Do the initial load command quietly.
+ In samount, if we succeed, set the relative position markers.
not per-process. Keep it in `switchtime' consistently.
It is now clear that the timestamp is always valid in fork_trampoline()
except when the child is running on a previously idle cpu, which
can only happen if there are multiple cpus, so don't check or set
the timestamp in fork_trampoline except in the (i386) SMP case.
Just remove the alpha code for setting it unconditionally, since
there is no SMP case for alpha and the code had rotted.
Parts reviewed by: dfr, phk
Submitted by: Matthew Dillon <dillon@apollo.backplane.com>
To prevent a deadlock, if we are extremely low on memory, force synchronous
operation by the VOP_PUTPAGES in vnode_pager_putpages.
to calculate a reasonable size for the swap partition).
* Fix a typo in remrq() where a process with idle priority would not be
correctly removed from the relavent queue. Note that realtime and idle
priorities are still not supported since the assembler code in
cpu_switch() does not check the realtime and idle queues.
- Transparent proxying support added.
- PPTP redirecting support added based on patches
contributed by Dru Nelson <dnelson@redwoodsoft.com>.
Submitted by: Charles Mott <cmott@srv.net>
drive has very poor write performance (1.4MB/sec vs. 12MB/sec) with anything
more than two oustanding transactions.
So, this limits the number of tagged commands to two for that drive.
Thanks to Paul van der Zwan for doing a whole lot of testing to confirm
this.
Reported by: Paul van der Zwan <paulz@trantor.xs4all.nl>
Specifically, the test was in the wrong place, lacked a cast, didn't
unlock the node, and exited to bad rather than abortit. Now we don't
allow renaming of a file with LINK_MAX references. Move the test to
earlier in the code as it is closer to where ip is obtained, as that
is the style of the rest of the function.
Didn't fix the problems bruce pointed out in the rename man page to
include EMLINK, nor address his complaints about how the whole idea of
incrementing the link count during a rename is potentially asking for
trouble.
Also didn't try to correct potential problem Terry pointed out with
decrements not being similarly protected against underflow.
Added autodetection of MMAC Osprey 100 card for
Jan Schmidt <mmedia@rz.uni-greifswald.de>. The MMAC card has an EEPROM
which contains an ASCII string beginning with "MMAC".
Corrected Hauppauge Audio Mux Mute value from 0x01 to 0x04.
Fixed a typo.
Sumitted change:
Added ALPS Tuner Type submitted by Hiroki Mori <mori@infocity.co.jp>
Submitted by: Roger Hardiman and Hiroki Mori <mori@infocity.co.jp>
