addressing if a packet is later re-encapsulated and sent to a
non-broadcast, non-multicast destination after being received on the
ng_ksocket input hook.
PR: 106999
Submitted by: Kevin Lahey
MFC after: 4 weeks
Formulas described in RFC require high precision of floating point.
Formulas of integer math implemented in ng_pptpgre give mistake in range
of +0-7ms on RTT and +0-3ms on deviation. This leads to significant
underestimation of real packet RTT.
I have made a very simple patch to reduce mistake to +4-3ms on RTT and
+2-1ms on deviation. Mistake in RTT is not good, but gets covered by
deviation. To cover worst possible negative mistake in deviation I have
added 2ms to it. Also this 2 ms cover the case when measured deviation
is so small (about zero) that it can interfere with process scheduling
delays or weather on Mars.
My tests show decreasing of packet losses on 20ms RTT link from 2.5% to
0.3% while speed increased un 1/3.
Reviewed by: archie
with bypass header, to send it out to userland.
- Use ng_ppp_bypass() in ng_ppp_proto_recv().
- Use ng_ppp_bypass() in ng_ppp_comp_recv() and in
ng_ppp_crypt_recv() if compression or encryption is
disabled, respectively.
- Any LCP packet goes directly to ng_ppp_bypass(), instead
of passing through PPP stack.
- Any non-LCP packet on disabled link is discarded. This
is behavior defined in RFC.
Submitted by: Alexander Motin <mav alkar.net>
hooks get their per hook rcvdata methods, and all functions are organized
corresponding to protocol stack model.
Submitted by: Alexander Motin <mav alkar.net>
Reviewed by: archie, julian
semantics.
- Stop testing bpf pointers for NULL. In some cases use
bpf_peers_present() and then call the function directly inside the
conditional block instead of the macro.
- For places where the entire conditional block is the macro, remove the
test and make the macro unconditional.
- Use BPF_MTAP() in if_pfsync on FreeBSD instead of an expanded version of
the old semantics.
Reviewed by: csjp (older version)
node would send every outgoing frame to the "compress" hook.
Packets received on the "compress" hook were expected to be
compressed and PROT_COMPD tag was put on them unconditionally.
After this commit an alternative compression mode can be set.
In this mode the node doesn't put the PROT_COMPD, the compressor
should put it itself. This is important for such kind of
compressors, that can submit uncompressed frames.
Before this commit, if the decompression is enabled, the ng_ppp(4)
node would send and incoming frame to the "decompress" hook
only if it has the PROT_COMPD proto tag on it.
After this commit an alternative decompression mode can be set.
In this mode the node sends all the incoming packets to the
decompression hook. This is important for such kind of compressors
that need uncompressed packets too, to keep their library in sync.
These new features will be used in new version of mpd4, and in new
compressor nodes.
Submitted by: Alexander Motin <mav alkar.net>
specific privilege names to a broad range of privileges. These may
require some future tweaking.
Sponsored by: nCircle Network Security, Inc.
Obtained from: TrustedBSD Project
Discussed on: arch@
Reviewed (at least in part) by: mlaier, jmg, pjd, bde, ceri,
Alex Lyashkov <umka at sevcity dot net>,
Skip Ford <skip dot ford at verizon dot net>,
Antoine Brodin <antoine dot brodin at laposte dot net>
mbuf clusters. Add a flags parameter to accept M_PKTHDR and M_EOR mbuf
chain flags. Provide compatibility macro for m_getm() calling m_getm2()
with M_PKTHDR set.
Rewrite m_uiotombuf() to use m_getm2() for mbuf allocation and do the
uiomove() in a tight loop over the mbuf chain. Add a flags parameter to
accept mbuf flags to be passed to m_getm2(). Adjust all callers for the
extra parameter.
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 month
- Inline ship_msg() into ngs_rcvmsg().
- Plug memory leak in case if no control socket present.
- Remove malloc() and allocate the sockaddr on stack.
- style(9).
- Use malloc() and free() instead of MALLOC() and FREE() macros.
- Do not check malloc results if M_WAITOK was used.
- Remove linked list of all netgraph sockets. It isn't needed.
- Use ng_findhook() instead of searching the list ourselves.
- Use NG_WAITOK in syscalls.
- Remove unneeded includes.
- style(9)
m_pkthdr.ether_vlan. The presence of the M_VLANTAG flag on the mbuf
signifies the presence and validity of its content.
Drivers that support hardware VLAN tag stripping fill in the received
VLAN tag (containing both vlan and priority information) into the
ether_vtag mbuf packet header field:
m->m_pkthdr.ether_vtag = vlan_id; /* ntohs()? */
m->m_flags |= M_VLANTAG;
to mark the packet m with the specified VLAN tag.
On output the driver should check the mbuf for the M_VLANTAG flag to
see if a VLAN tag is present and valid:
if (m->m_flags & M_VLANTAG) {
... = m->m_pkthdr.ether_vtag; /* htons()? */
... pass tag to hardware ...
}
VLAN tags are stored in host byte order. Byte swapping may be necessary.
(Note: This driver conversion was mechanic and did not add or remove any
byte swapping in the drivers.)
Remove zone_mtag_vlan UMA zone and MTAG_VLAN definition. No more tag
memory allocation have to be done.
Reviewed by: thompsa, yar
Sponsored by: TCP/IP Optimization Fundraise 2005
of individual interfaces should match the ipackets/ibytes counter of
the aggregate (FEC) interface.
PR: kern/82189
Submitted by: Stikheev Andrew <sand AT zunet DOT ru>
MFC after: 3 days
trunk ports first. If that succeeds, and we're inside our own bounds,
so be it.
Still not ideal -- adding a port after changing an MTU doesn't change
port's MTU, but a step in the right direction.
PR: kern/95417
Submitted by: Vladimir Ivanov <wawa AT yandex-team DOT ru>
MFC after: 3 days
I've slightly edited a patch to make the conditional logic positive
and remove (what I think was) a redundant ng_fec_init() call.
are supposed to be set directly in ifnet already. This change fixes a
panic when ng_eiface node is attached to ng_fec node and the latter is
shut down (ng_fec sets flags and then calls SIOCSIFFLAGS with a NULL
argument).
MFC after: 3 days
- Fix a couple of LORs and panics;
- Temporarily remove the code that tries to cleanup sockets that stuck
on accepting queues (both complete and incomplete). I'm taking an ostrich
approach here until I find a better way to deal with sockets that were
disconnected before accepting (i.e. while socket was on complete or
incomplete accept queue).
- Store the Ethernet header in node softc.
- Initialize header with dst addr and ethertype in node
constructor method.
- In node connect method send NGM_ETHER_GET_ENADDR message
downwards.
- If received reply from ng_ether(4) store the src addr
in softc.
- Add NGM_PPPOE_SETENDADDR message that allows user to
override the address with whatever he/she wants.
- Print node ID, where possible.
- Prepend log messages with function name, or at least with "ng_pppoe".
Reviewed by: julian
Tested by: Joao Barros <joao.barros gmail.com>
on output frames.
Many people were confused with not working CARP, ng_bridge(4)
and other subsystems, because ng_ether(4) overwritten source
MAC address.
soreceive(), and sopoll(), which are wrappers for pru_sosend,
pru_soreceive, and pru_sopoll, and are now used univerally by socket
consumers rather than either directly invoking the old so*() functions
or directly invoking the protocol switch method (about an even split
prior to this commit).
This completes an architectural change that was begun in 1996 to permit
protocols to provide substitute implementations, as now used by UDP.
Consumers now uniformly invoke sosend(), soreceive(), and sopoll() to
perform these operations on sockets -- in particular, distributed file
systems and socket system calls.
Architectural head nod: sam, gnn, wollman
function, pru_close, to notify protocols that the file descriptor or
other consumer of a socket is closing the socket. pru_abort is now a
notification of close also, and no longer detaches. pru_detach is no
longer used to notify of close, and will be called during socket
tear-down by sofree() when all references to a socket evaporate after
an earlier call to abort or close the socket. This means detach is now
an unconditional teardown of a socket, whereas previously sockets could
persist after detach of the protocol retained a reference.
This faciliates sharing mutexes between layers of the network stack as
the mutex is required during the checking and removal of references at
the head of sofree(). With this change, pru_detach can now assume that
the mutex will no longer be required by the socket layer after
completion, whereas before this was not necessarily true.
Reviewed by: gnn
we intend for the user to be able to unload them later via kldunload(2)
instead of calling linker_load_module() and then directly adjusting the
ref count on the linker file structure. This makes the resulting
consumer code simpler and cleaner and better hides the linker internals
making it possible to sanely lock the linker.
use this ioctl to obtain the list of HCI nodes. User-space application
is expected to preallocate 'ng_btsocket_hci_raw_node_list_names' structure
and set limit in 'num_nodes' field. The 'nodes' field should be allocated
as well and it should have space for at least 'num_nodes' elements.
The SIOC_HCI_RAW_NODE_LIST_NAMES should be issued on bound raw HCI socket.
It does not really really matter what HCI name the socket is bound to, as
long as it is not empty.
MFC after: 1 week
sampling_interval) fields in netflow v5 header. We do not use
them but some netflow tools show garbage.
PR: kern/96296
Submitted by: David Duchscher
Approved by: glebius
MFC after: 1 week
rather than an error. Detaches do not "fail", they other occur or
the protocol flags SS_PROTOREF to take ownership of the socket.
soclose() no longer looks at so_pcb to see if it's NULL, relying
entirely on the protocol to decide whether it's time to free the
socket or not using SS_PROTOREF. so_pcb is now entirely owned and
managed by the protocol code. Likewise, no longer test so_pcb in
other socket functions, such as soreceive(), which have no business
digging into protocol internals.
Protocol detach routines no longer try to free the socket on detach,
this is performed in the socket code if the protocol permits it.
In rts_detach(), no longer test for rp != NULL in detach, and
likewise in other protocols that don't permit a NULL so_pcb, reduce
the incidence of testing for it during detach.
netinet and netinet6 are not fully updated to this change, which
will be in an upcoming commit. In their current state they may leak
memory or panic.
MFC after: 3 months
than an int, as an error here is not meaningful. Modify soabort() to
unconditionally free the socket on the return of pru_abort(), and
modify most protocols to no longer conditionally free the socket,
since the caller will do this.
This commit likely leaves parts of netinet and netinet6 in a situation
where they may panic or leak memory, as they have not are not fully
updated by this commit. This will be corrected shortly in followup
commits to these components.
MFC after: 3 months
if ksocket is connected to an interface-type node somewhere later
in the graph (e.g., ng_eiface or ng_iface), the csum_data may be
applied to a wrong packet (if we encapsulate Ethernet or IP).
MFC after: 3 days
- Run send queue down to completion, not just one packet.
It has been observed to cause a stall queue otherwise.
- Prevent queueing multiple function calls to a node.
MFC after: 3 days
by NGM_PPPOE_SETMODE message. When D-Link compat mode is on, we will
broadcast PADI with empty Service-Name to all listening hooks.
o Rewrite the compatibility options. Before we had two modes - standard
and non-standard (aka 3Com). Now we have standard mode and two compat
flags, that can be combined.
o Be consistent and do s/STUPID/3COM/g. I don't say that 3Com mode isn't
stupid, just want to make code easier to read.
PPPoE AC, servicing a specific Service-Name, when client sends a PADI
with an empty Service-Name. Should it reply with all available service
names or should it be silent? Our implementation had chosen the latter,
while some other had chosen the former (they say Linux and Cisco). Now
some PPPoE clients appear, that rely on the assumption that AC will
send all names in a PADO reply to a PADI with wildcard Service-Name.
These clients can't connect to FreeBSD AC.
I have requested comments from authors of RFC2516 via email, but
received no reply.
This change makes FreeBSD AC compatible with D-Link DI-614+ and
D-Link DI-624+ SOHO routers, and probably others.
Big thanks to D-Link's Russian office, namely Victor Platov, for
assistance and support in investigation and testing of this change.
Details:
o Split pppoe_match_svc() into three different functions serving
different purposes:
- pppoe_match_svc() - match non-empty Service-Name tag from PADI
against all available hooks in listening state.
- pppoe_find_svc() - check that given Service-Name is not yet
registered.
- pppoe_broadcast_padi() - send a copy of PADI packet with empty
Service-Name tag to all listening hooks.
o For NGM_PPPOE_LISTEN message use pppoe_find_svc().
o In ng_pppoe_rcvdata() in a PADI case use pppoe_match_svc() for
a non-empty Service-Name tag, and pppoe_broadcast_padi() in
either case.
A side effect from the above changes is that now pppoed(8) and mpd
will reply to a empty Service-Name PADI sending a PADO with two
Service-Name tags - an empty one and correct one. This is not fatal,
and will be corrected in pppoed(8) and mpd later. No need to update
node interface version.
Supported by: D-Link
in flags. When sending export datagram from expiry thread, then
use default zero flags. This removes unpleasant contention of the
interrupt thread on mutexes (usually ng_ksocket's socket buffer
mutex).
had been replied, the reply was always delivered to the originator
synchronously.
With introduction of netgraph item callbacks and a wait channel with
mutex in ng_socket(4), we have fixed the problem with ngctl(8) returning
earlier than the command has been proceeded by target node. But still
ngctl(8) can return prior to the reply has arrived to its node.
To fix this:
- Introduce a new flag for netgraph(4) messages - NGM_HASREPLY.
This flag is or'ed with message like NGM_READONLY.
- In netgraph userland library if we have sent a message with
NGM_HASREPLY flag, then select(2) until reply comes.
- Mark appropriate generic commands with NGM_HASREPLY flag,
gathering them into one enum {}. Bump generic cookie.
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
a synchronous reprogramming of hardware MAC filters if the physical
interface are up and running. Previously, MAC filters would be
reconfigured only when the fec interface was brought up.
- Disallow bundle reconfiguration when virtual
interface is running; otherwise, removing a
port from a running configuration will cause
a panic in the start() method on the next packet
on an assumption that a bundle has an even
number of ports (2 or 4).
- Disallow bringing of virtual interface to a
running state when a bundle size is 0; otherwise,
adding and then removing the port will similarly
cause a panic.
- Add missing initialization of fec_ifstat when
adding a new port and fix media status reporting
when virtual interface isn't yet up (check for
fec_status of 1 rather than != 0).
previously, ifp->if_type was set to IFT_ETHER by
ether_ifattach(), now it's done by if_alloc() so
an assignment of if_type to IFT_PROPVIRTUAL after
if_alloc() but before ether_ifattach() broke it.
This makes arp(8) and friends happy about the fec
interfaces, and will allow us to use if_setlladdr()
on the fec interface.
- Set/reset IFF_DRV_RUNNING/IFF_DRV_OACTIVE in init()
and stop() methods rather than in ioctl(), like the
rest of the drivers do. This fixes a bug when an
"ifconfig fec0 ipv4_address" would not have made
the interface running, didn't launch the ticker
function to track media status of bundled ports,
etc.
destruction:
- Backout 1.62, since it doesn't fix all possible
problems.
- Upon node creation, put an additional reference on node.
- Add a mutex and refcounter to struct ngsock. Netgraph node,
control socket and data socket all count as references.
- Introduce ng_socket_free_priv() which removes one reference
from ngsock, and frees it when all references has gone.
- No direct pointers between pcbs and node, all pointing
is done via struct ngsock and protected with mutex.
- Introduce ng_topo_mtx, a mutex to protect topology changes.
- In ng_destroy_node() protect with ng_topo_mtx the process
of checking and pointing at ng_deadnode. [1]
- In ng_con_part2() check that our peer is not a ng_deadnode,
and protect the check with ng_topo_mtx.
- Add KASSERTs to ng_acquire_read/write, to make more
understandible synopsis in case if called on ng_deadnode.
Reported by: Roselyn Lee [1]
- Introduce a new flags NGQF_QREADER and NGQF_QWRITER,
which tell how the item should be actually applied,
overriding NGQF_READER/NGQF_WRITER flags.
- Do not differ between pending reader or writer. Use only
one flag that is raised, when there are pending items.
- Schedule netgraph ISR in ng_queue_rw(), so that callers
do not need to do this job.
- Fix several comments.
Submitted by: julian
- Prefer '_' to ' ', as it results in more easily parsed results in
memory monitoring tools such as vmstat.
- Remove punctuation that is incompatible with using memory type names
as file names, such as '/' characters.
- Disambiguate some collisions by adding subsystem prefixes to some
memory types.
- Generally prefer lower case to upper case.
- If the same type is defined in multiple architecture directories,
attempt to use the same name in additional cases.
Not all instances were caught in this change, so more work is required to
finish this conversion. Similar changes are required for UMA zone names.
following the protocol pru_listen() call to solisten_proto(), so
that it occurs under the socket lock acquisition that also sets
SO_ACCEPTCONN. This requires passing the new backlog parameter
to the protocol, which also allows the protocol to be aware of
changes in queue limit should it wish to do something about the
new queue limit. This continues a move towards the socket layer
acting as a library for the protocol.
Bump __FreeBSD_version due to a change in the in-kernel protocol
interface. This change has been tested with IPv4 and UNIX domain
sockets, but not other protocols.
provided in the kernel build directory, fix modules that were
failing to build this way due to not quite correct kernel option
usage. In particular:
ng_mppc.c uses two complementary options, both of which are listed
in sys/conf/files. Ideally, there should be a separate option for
including ng_mppc.c in kernel build, but now only
NETGRAPH_MPPC_ENCRYPTION is usable anyway, the other one requires
proprietary files.
nwfs and smbfs were trying to ensure they were built with proper
network components, but the check was rather questionable.
Discussed with: ru
- move the function pointer definitions to if_bridgevar.h
- move most of the logic to the new BRIDGE_INPUT and BRIDGE_OUTPUT macros
- remove unneeded functions from if_bridgevar.h and sort a little.
semantics, and then was reused for next node, it still would be applied
as writer again.
To fix the regression the decision is made never to alter item->el_flags
after the item has been allocated. This requires checking for overrides
both in ng_dequeue() and in ng_snd_item().
Details:
- Caller of the ng_apply_item() knows what is the current access to
node and specifies it to ng_apply_item(). The latter drops the
given access after item has beem applied.
- ng_dequeue() needs to be supplied with int pointer, where it stores
the obtained access on node.
- Check for node/hook access overrides in ng_dequeue().
http://lists.freebsd.org/pipermail/cvs-src/2004-October/033496.html
The same problem applies to if_bridge(4), too.
- Copy-and-paste the if_bridge(4) related block from
if_ethersubr.c to ng_ether.c
- Add XXXs, so that copy-and-paste would be noticed by
any future editors of this code.
- Also add XXXs near if_bridge(4) declarations.
Silence from: thompsa
replacement and has additional features which make it superior.
Discussed on: -arch
Reviewed by: thompsa
X-MFC-after: never (RELENG_6 as transition period)
times consequently, without checking whether callout has been serviced
or not. (ng_pptpgre and ng_ppp were catched in this behavior).
- In ng_callout() save old item before calling callout_reset(). If the
latter has returned 1, then free this item.
- In ng_uncallout() clear c->c_arg.
Problem reported by: Alexandre Kardanev
First, mutexed callouts are incompatible with netgraph nodes, because
netgraph(4) can guarantee that the function will be called with mutex
held.
Second, nodes should not send data to their neighbor holding their
mutex. A node does not know what stack can it enter sending data in
some direction. May be executing will encounter a place to sleep.
New locking:
- ng_pptpgre_recv() and ng_pptpgre_xmit() must be entered with mutex held.
- ng_pptpgre_recv() and ng_pptpgre_xmit() unlock mutex before
sending data and then return unlocked.
- callout routines acquire mutex themselves.
does not clear m_nextpkt for us. The mbufs are sent into netgraph and
then, if they contain a TCP packet delivered locally, they will enter
socket code again. They can pass the first assert in sbappendstream()
because m_nextpkt may be set not in the first mbuf, but deeper in the
chain. So the problem will trigger much later, when local program
reads the data from socket, and an mbuf with m_nextpkt becomes a
first one.
This bug was demasked by revision 1.54, when I made upcall queueable.
Before revision 1.54 there was a very small probability to have 2
mbufs in GRE socket buffer, because ng_ksocket_incoming2() dequeued
the first one immediately.
- in ng_ksocket_incoming2() clear m_nextpkt on all mbufs
read from socket.
- restore rev. 1.54 change in ng_ksocket_incoming().
PR: kern/84952
PR: kern/82413
In collaboration with: rwatson
panic. The panic happens when outgoing L2CAP connection descriptor is
deleted with the L2CAP command(s) pending in the queue. In this case when
the last L2CAP command is deleted (due to cleanup) and reference counter
for the L2CAP connection goes down to zero the auto disconnect timeout
is incorrectly set. pjd gets credit for tracking this down and committing
bandaid.
Reported by: Jonatan B <onatan at gmail dot com>
MFC after: 3 days
parallel ng_pptp_rcvdata():
- Add a per-node mutex.
- Acquire mutex during all ng_pptp_rcvdata() method.
- Make callouts protected by mutex. Now callouts count as
netgraph writers, but there are plans to allow reader callouts
for nodes, that have internal locking.
- Acquire mutex in ng_pptp_reset(), which can be triggered
by a message or node shutdown.
PR: kern/80035
Tested by: Deomid Ryabkov <myself rojer.pp.ru>
Reviewed by: Deomid Ryabkov <myself rojer.pp.ru>
either reader or writer flag on item in the function, that
allocates the item. Do not modify these flags when item is
applied or queued.
The only exceptions are node and hook overrides - they can
change item flags to writer.
the code, i.e. ng_fec_init() is called with the ifp->if_softc pointer and
NOT with the ifp pointer.
PR: kern/85239
Reviewed by: brooks
MFC after: 1 day
it fixes. I believe the problem lives somewhere outside ng_ksocket,
but until it is found, let the node be working.
PR: kern/84952
PR: kern/82413
MFC after: 3 days
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
data link type of the hook. It will be used to ease autoconfiguration
of netgraph and also to print warning messages, when incompatoble nodes
are connected together.
At the end of ng_snd_item(), node queue is processed. In certain
netgraph setups deep recursive calls can occur.
For example this happens, when two nodes are connected and can send
items to each other in both directions. If, for some reason, both nodes
have a lot of items in their queues, then the processing thread will
recurse between these two nodes, delivering items left and right, going
deeper in the stack. Other setups can suffer from deep recursion, too.
The following factors can influence risk of deep netgraph call:
- periodical write-access events on node
- combination of slow link and fast one in one graph
- net.inet.ip.fastforwarding
Changes made:
- In ng_acquire_{read,write}() do not dequeue another item. Instead,
call ng_setisr() for this node.
- At the end of ng_snd_item(), do not process queue. Call ng_setisr(),
if there are any dequeueable items on node queue.
- In ng_setisr() narrow worklist mutex holding.
- In ng_setisr() assert queue mutex.
Theoretically, the first two changes should negatively affect performance.
To check this, some profiling was made:
1) In general real tasks, no noticable performance difference was found.
2) The following test was made: two multithreaded nodes and one
single-threaded were connected into a ring. A large queues of packets
were sent around this ring. Time to pass the ring N times was measured.
This is a very vacuous test: no items/mbufs are allocated, no upcalls or
downcalls outside of netgraph. It doesn't represent a real load, it is
a stress test for ng_acquire_{read,write}() and item queueing functions.
Surprisingly, the performance impact was positive! New code is 13% faster
on UP and 17% faster on SMP, in this particular test.
The problem was originally found, described, analyzed and original patch
was written by Roselyn Lee from Vernier Networks. Thanks!
Submitted by: Roselyn Lee <rosel verniernetworks com>
It does not work with ng_ubt(4) and require special driver and firmware.
Obtained from: Marcel Holtmann < marcel at holtmann dot org >
Submitted by: Rainer Goellner < rainer at jabbe dot de >
MFC after: 3 days
there are at least two versions of the adapter. Version 1 (product ID 0x2200)
of the adapter does not work with ng_ubt(4) and require special driver and
firmware. Version 2 (product ID 0x3800) seems to work just fine, except it
does not have bDeviceClass, bDeviceSubClass and bDeviceProtocol set to required
(by specification) values. This change forces ng_ubt(4) to attach to the
version 2 adapter.
Obtained from: Marcel Holtmann <marcel at holtmann dot org>
Submitted by: Rainer Goellner <rainer at jabbe dot de>
PPPoE modes. The interface was declared obsoleted before 5.3-RELEASE.
When running as access concentrator ng_pppoe(4) supports both modes
simultanously. When running as client mode can be swicthed in ppp(8)
configuration.
Approved by: re (scottl)
an item may be queued and processed later. While this is OK for mbufs,
this is a problem for control messages.
In the framework:
- Add optional callback function pointer to an item. When item gets
applied the callback is executed from ng_apply_item().
- Add new flag NG_PROGRESS. If this flag is supplied, then return
EINPROGRESS instead of 0 in case if item failed to deliver
synchronously and was queued.
- Honor NG_PROGRESS in ng_snd_item().
In ng_socket:
- When userland sends control message add callback to the item.
- If ng_snd_item() returns EINPROGRESS, then sleep.
This change fixes possible races in ngctl(8) scripts.
Reviewed by: julian
Approved by: re (scottl)
a DLT_NULL interface. In particular:
1) Consistently use type u_int32_t for the header of a
DLT_NULL device - it continues to represent the address
family as always.
2) In the DLT_NULL case get bpf_movein to store the u_int32_t
in a sockaddr rather than in the mbuf, to be consistent
with all the DLT types.
3) Consequently fix a bug in bpf_movein/bpfwrite which
only permitted packets up to 4 bytes less than the MTU
to be written.
4) Fix all DLT_NULL devices to have the code required to
allow writing to their bpf devices.
5) Move the code to allow writing to if_lo from if_simloop
to looutput, because it only applies to DLT_NULL devices
but was being applied to other devices that use if_simloop
possibly incorrectly.
PR: 82157
Submitted by: Matthew Luckie <mjl@luckie.org.nz>
Approved by: re (scottl)
Provide a backwards compatible way to have the extra macro by defining
PCCARD_API_LEVEL 5 before including pccarddevs for driver writers that
want/need to have the same driver on 5 and 6 with pccard attachments.
Approved by: re (dwhite)
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
- Do not edit pullup_len outside M_CHECK macro.
- Do not reimplement NG_FWD_NEW_DATA().
- Remove redundant check for item being not NULL.
Submitted by: ru
hack MSS of packets outgoing via interface with small MTU, to workaround
path MTU discovery problems.
Written by Alexey Popov, with some cleanups from me. There are also plans
to improve mpd port, so that it uses this node, instead of doing MSS
hacking in userland, when 'enable tcpmssfix' option is on.
Submitted by: Alexey Popov <lollypop@flexuser.ru>
Note: len gets intialized to 0 for sap == NULL case only to
make compiler on amd64 happy. This has nothing todo with the
former uninitialized use of len in sap != NULL case.
Reviewed by: glebius
Approved by: pjd (mentor)
specified by caller.
- Change ng_send_item() interface - use 'flags' argument instead of
boolean 'queue'.
- Extend ng_send_fn(), ng_package_data() and ng_package_msg()
interface - add possibility to pass flags. Rename ng_send_fn() to
ng_send_fn1(). Create macro for ng_send_fn().
- Update all macros, that use ng_package_data() and ng_package_msg().
Reviewed by: julian
The most significant changes are:
- Use UMA zone instead of own chunk of memory.
- Lock each hash entry separately.
- Expire items "actively" - interrupt method can expire flows
from hash slot, when it searches through it.
- Remove global tailqueue. Make callout thread search through
every hash slot.
- Export datagram is detached from private data and filled. If
it is incomplete, it is attached back. Another thread will
continue working with it.
Lesser, but also important speedups:
- Flows in hash slot are stored in tailqueue. Whenever a flow is
hit, it is moved to the begging, so it can be located quicker.
- When callout thread works with hash slot it bails out if
slot mutex is contested.
to the mbuf. Offset cannot exceed MHLEN bytes. This is currently used to
fix Ethernet header alignment problem on alpha and sparc64. Also change all
users of m_uiotombuf to pass proper offset.
Reviewed by: jmg, sam
Tested by: Sten Spans "sten AT blinkenlights DOT nl"
MFC after: 1 week
protocol. RFCOMM is a SOCK_STREAM protocol not SOCK_SEQPACKET. This was a
serious bug caused by cut-and-paste. I'm surprised it did not bite me before.
Dunce hat goes to me.
MFC after: 3 days
EA bit is set in hdr->length (16-bit length). This currently has no effect
on the rest of the code. It just fixes the debug message.
MFC After: 3 weeks
Functional changes:
- Cut struct source_hookinfo. Just use hook_p pointer.
- Remove "start_now" command. "start" command now requires number of
packets to send as argument. "start" command actually starts sending.
Move the code that actually starts sending from ng_source_rcvmsg()
to ng_source_start().
- Remove check for NG_SOURCE_ACTIVE in ng_source_stop(). We can be called
with flag cleared (see begin of ng_source_intr()).
- If NG_SEND_DATA_ONLY() use log(LOG_DEBUG) instead of printf(). Otherwise
we will *flood* console.
- Add ng_connect_t method, which sends NGM_ETHER_GET_IFNAME command
to "output" hook. Cut ng_source_request_output_ifp(). Refactor
ng_source_store_output_ifp() to use ifunit() and don't muck through
interface list.
- Add "setiface" command, which gives ability to configure interface
in case when ng_source_connect() failed. This happens, when we are not
connected directly to ng_ether(4) node.
- Remove KASSERTs, which can never fire.
- Don't check for M_PKTHDR in rcvdata method. netgraph(4) does this
for us.
Style:
- Assign sc_p = NG_NODE_PRIVATE(node) in declaration, to be
consistent with style of other nodes.
- Sort variables.
- u_intXX -> uintXX.
- Dots at ends of comments.
Sponsored by: Rambler
be pass-thru mode, when traffic is not copied by ng_tee, but passed thru
ng_netflow.
Changes made:
- In ng_netflow_rcvdata() do all necessary pulluping: Ethernet header,
IP header, and TCP/UDP header.
- Pass only pointer to struct ip to ng_netflow_flow_add(). Any TCP/UDP
headers are guaranteed to by after it.
- Merge make_flow_rec() function into ng_netflow_flow_add().
be pass-thru mode, when traffic is not copied by ng_tee, but passed thru
ng_netflow.
Changes made:
- In ng_netflow_rcvdata() do all necessary pulluping: Ethernet header,
IP header, and TCP/UDP header.
- Pass only pointer to struct ip to ng_netflow_flow_add(). Any TCP/UDP
headers are guaranteed to by after it.
- Merge make_flow_rec() function into ng_netflow_flow_add().
precision when IP packet may travel through internet for several seconds.
Also uptime measured in milliseconds overflows every 48+ days.
But we have to do same to keep compatibility with Cisco and flow-tools.
Make a macro MILLIUPTIME, which does overflowable multiplication to 1000.
Requested by: Sergey Ryabin, Oleg Bulyzhin
MFC after: 1 week
its return value and free resources if function returns error. Plug
several memory leaks with this change.
Submitted by: archie
Found by: Coverity Prevent analysis tool
a socket from a regular socket to a listening socket able to accept new
connections. As part of this state transition, solisten() calls into the
protocol to update protocol-layer state. There were several bugs in this
implementation that could result in a race wherein a TCP SYN received
in the interval between the protocol state transition and the shortly
following socket layer transition would result in a panic in the TCP code,
as the socket would be in the TCPS_LISTEN state, but the socket would not
have the SO_ACCEPTCONN flag set.
This change does the following:
- Pushes the socket state transition from the socket layer solisten() to
to socket "library" routines called from the protocol. This permits
the socket routines to be called while holding the protocol mutexes,
preventing a race exposing the incomplete socket state transition to TCP
after the TCP state transition has completed. The check for a socket
layer state transition is performed by solisten_proto_check(), and the
actual transition is performed by solisten_proto().
- Holds the socket lock for the duration of the socket state test and set,
and over the protocol layer state transition, which is now possible as
the socket lock is acquired by the protocol layer, rather than vice
versa. This prevents additional state related races in the socket
layer.
This permits the dual transition of socket layer and protocol layer state
to occur while holding locks for both layers, making the two changes
atomic with respect to one another. Similar changes are likely require
elsewhere in the socket/protocol code.
Reported by: Peter Holm <peter@holm.cc>
Review and fixes from: emax, Antoine Brodin <antoine.brodin@laposte.net>
Philosophical head nod: gnn
- refactor ngd_constructor, so that make_dev() is called without
any locks held, since it mallocs memory with M_WAITOK flag.
- rename global mtx, to have name different to per-node mtx
MFC after: 2 weeks
removes netgraph node and unwraps Ethernet interface.
This gives us ability to unload ng_ether.ko, when all interfaces
are detached, making ng_ether(4) developers happy.
Reviewed by: ru
