I created and tested this with a custom FreeSBIE cd-image.
PR: i386/96452
Submitted by: Yuichiro Goto <y7goto at gmail dot com>
MFC after: 3 days
Approved by: imp (mentor)
inode's i_flag.
It's possible that after ufs_infactive() calls softdep_releasefile(),
i_nlink stays >0 for a considerable amount of time (> 60 seconds here).
During this period, any ffs allocation routines that alter di_blocks
must also account for the blocks in the filesystem's fs_pendingblocks
value.
This change fixes an eventual df/du discrepency that will happen as
the result of fs_pendingblocks being reduced to <0.
The only manifestation of this that people may recognise is the
following message on boot:
/somefs: update error: blocks -N files M
at which point the negative pending block count is adjusted to zero.
Reviewed by: tegge
MFC after: 3 weeks
freshly-loaded kernel module. To avoid various unload races, hide linker
files whose sysinit's are being run from userland so that they can't be
kldunloaded until after all the sysinit's have finished.
Tested by: gallatin
changes. This should ease the job of maintaining codebase since much
of the regression tests are done across os versions.
- bus_setup_intr() -> snd_setup_intr().
triggers a KASSERT) or local variables. In the case of kern_ndis, the
tsleep() actually used a common sleep address (curproc) making it
susceptible to a premature wakeup.
want an equivalent of DELAY(9) that sleeps instead of spins. It accepts
a wmesg and a timeout and is not interrupted by signals. It uses a private
wait channel that should never be woken up by wakeup(9) or wakeup_one(9).
Glanced at by: phk
Use bus_get_dma_tag() to obtain the parent DMA tag to make the drivers
a little bit more non-ia32/amd64 friendly.
There is no man page for bus_get_dma_tag, so this is modelled after
rev. 1.62 of src/sys/dev/sound/pci/es137x.c by marius.
Inspired by: commit by marius
attachment of new devices that arrive (and we notice them
via async Fibre Channel events). We've always had the
right thing (of sorts) happen when devices go away- this
is the corollary function that makes multipath failover
actually work.
MFC after: 2 weeks
rescan requests. The purpose of this is to allow a SIM
(or other entities) to request a bus rescan and have it
then fielded in a different (process) context from the
caller.
There are probably better ways to accomplish this, but
it's a very small change that helps solve a number of
problems.
Reviewed by: Justin, Ken and Scott.
MFC after: 2 weeks
early, we haven't set board type, so we can't correctly check for
some options. Fix this by splitting option setting/getting into
generic, pci and then later board specific, option setting/getting.
This was noticed when setting 'iid' (or 'hard loop id') didn't work
all of a sudden.
Noticed by: Mike Drangula (thanks!) via Jung-uk Kim (thanks!)
incoming packets have had their 802.1Q tags processed by the
hardware, resulting in them being stripped from the packets, and
placed on the mbuf. This fixes the processing of 802.1Q tags when
hardware offload of 802.1Q tags is enabled.
check that the subject has read/write access to the vnode using the
vnode MAC check.
MFC after: 3 weeks
Submitted by: Spencer Minear <spencer_minear at securecomputing dot com>
Obtained from: TrustedBSD Project
a link-layer multicast group membership.
Such memberships are needed in order to support protocols such as
IS-IS without putting the interface into PROMISC or ALLMULTI modes.
sa_equal() is not OK for comparing sockaddr_dl as it has deeper structure
than a simple byte array, so add sa_dl_equal() and use that instead.
Reviewed by: rwatson
Verified with: /usr/sbin/mtest
Bug found by: Jouke Witteveen
MFC after: 2 weeks
addition of SerDes support. According to the docs, the 5706C and 5708C
phys are supposed to use the same MII model that is separate from the
SerDes parts, but the 5706C actually uses the MII model of the SerDes
parts. To fix this, readd the old 5706C entry to miidevs and add a
special check in brgphy_probe() for phys that match the 5706C ID. If
the phy is supported by the gentbi(4) driver, then it's a SerDes phy, so
we fail the probe and let gentbi(4) grab it. Otherwise, it's a 5706C phy,
so we let brgphy(4) grab it.
In coordination with: dwhite
treated as multicast frames and filtered, but when only when "adopting"
running firmware. By "adopting", I mean using pre-existing firmware
loaded from eeprom at PCI reset, rather than firmware loaded by the
driver.
non consecutively numbered ports.
This should fix current SATA problems.
Support AHCI chips where the ports are not consecutively numbered as in
some incarnations of the ICH8 chip.
flash card reader.
Also remove an 'Opened da0 -> <random number>' which is not needed on a daily
basis (available through bootverbose).
Reviewed by: phk, ken
MFC after: 1 week
and make it print under debug.iwi control same as other debugging stuff.
Remove the device_printf() in iwi_ioctl() and replace with this:
/*
* wait until pending iwi_cmd() are completed, to avoid races
* that could cause problems.
*/
while (sc->flags & IWI_FLAG_BUSY)
msleep(sc, &sc->sc_mtx, 0, "iwiioctl", hz);
This at least prevents what has become an almost systematic failure for my
system, presumably due to a previous iwi_cmd() not complete yet by the
time iwi_ioctl() is called.
It has been pointed to my attention that the real problem could be
calling ieee80211_ioctl() with the lock held. If that is true,
there might still be a possibility for a race condition e.g. an
interrupt coming while the ioctl is sleeping.
Need to investigate further on what changes are required to release
the lock before calling ieee80211_ioctl
+ do not release the dma-ble region used for downloading firmware.
This should fix the problems that some people were seeing, due to
memory becoming too fragmented which prevented subsequent allocations
of a suitable contiguous region of memory;
+ document the firmware format and usage in if_iwivar.h
+ use a loop to allocate the four tx rings, instead of replicating
the body of the loop.
+ add debugging code IWI_LOCK_ASSERT() to detect missing locks.
These only do a printf, and should go away once we figure out why
the driver sometimes freezes the system due to a (yet unidentified)
race condition.
+ add a device_printf() in iwi_ioctl() in certain conditions
(see comment in the code). This helps preventing the race condition
mentioned above, and makes the system survive. This printf will
also go away once fixing this bug is completed.
+ change iwi_getfw() to return 0 on success, 1 on error, consistently
with other functions.
+ fix the argument of a sizeof() in iwi_get_firmware()
+ use le32toh() to access little-endian fields
+ simplify error handling in iwi_load_firmware() and iwi_init_locked()
The bugs fixed by this commit (the freezing one especially) are serious
enough to call for a quick MFC
MFC after: 3 days
