- Use callout(9) instead of timeout(9).
- Use the existing hba lock as the CAM sim lock instead of Giant.
- Mark interrupt handler MPSAFE.
- Reorder detach and destroy the hba lock in detach.
Reviewed by: Steve Chang <ychang@highpoint-tech.com>
mostly by adjustments to debugging printf() format specifiers. For high
numbered LUNs, also switch to printing them in hex as per SAM-5.
MFC after: 2 weeks
original, this hides the contents of cam_compat.h from ktrace/kdump/truss,
avoiding problems there. There are no user-servicable parts in there, so
no need for those tools to be groping around in there.
Approved by: re
- Remove the timeout_ch field. It's been deprecated since FreeBSD 7.0;
MPSAFE drivers should be managing their own timeout storage. The
remaining non-MPSAFE drivers have been modified to also manage their own
storage, and should be considered for updating to MPSAFE (or removal)
during the FreeBSD 10.x lifecycle.
- Add fields related to soft timeouts and quality of service, to be used
in upcoming work.
- Add room for more flags in the CCB header and path_inq structures.
- Begin support for extended 64-bit LUNs.
- Bump the CAM version number to 0x18, but add compat shims. Tested with
camcontrol and smartctl.
Reviewed by: nathanw, ken, kib
Approved by: re
Obtained from: Netflix
controllers. Update the hptiop(4) manual page to reflect this
as well as mentioning that some cards are already end-of-life.
Many thanks to Highpoint for providing this driver update.
MFC after: 1 day
Stop abusing xpt_periph in random plases that really have no periph related
to CCB, for example, bus scanning. NULL value is fine in such cases and it
is correctly logged in debug messages as "noperiph". If at some point we
need some real XPT periphs (alike to pmpX now), quite likely they will be
per-bus, and not a single global instance as xpt_periph now.
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
RocketRAID 4500 series.
Many thanks to HighPoint Technologies for their continued support
of FreeBSD!
Submitted by: HighPoint Technologies
MFC after: 3 days
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
in GENERIC and LINT. [1]
- Rename hpt_dbg_level to hpt_iop_dbg_level to avoid multiple definition
of hpt_dbg_level (hptmv also has hpt_dbg_level).
PR: 127551 [1]
Reviewed by: scottl@
MFC after: 1 month
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
