system have been attached, but no later. This ensures that we do
not explore ohci or uhci busses before the companion echi controller
has been initialised, so it should fix the problem of multi-speed
USB devices getting attached as USB 1 devices first and then
re-attached as USB 2.
Some further changes are needed on architectures that do not currently
allow hooks to be inserted before configure_final() - alpha, ia64,
powerpc and sparc64. On these architectures the exploration will
now be delayed until the usb kthread runs.
alignment restrictive, and help performance on some ethernet cards which
currently copy the entire packet a couple bytes to get the packet aligned
properly...
Wordsmithing by: dwhite
Obtained from: NetBSD (code only)
I'll clean it up later: rwatson
in the window between the beginning of panic() and entering the debugger,
it's possible to receive interrupts. If we receive an interrupt, don't
preempt if panicstr != NULL, as the system is in the process of failing, and
the preempting thread is likely to stumble over the failure. The typical
scenario is during the printf() in panic() prior to entering the debugger,
but when running with a slower console type such as serial console.
It could be that the panic string should be passed to the debugger to print,
so that it can run from the debugger's environment rather than a regular
kernel printf.
Glanced at by: jhb
Do our best to plug some memory leaks (VPD data, jumbo memory buffer,...).
Log if we cannot free because memory still in use[1].
Change locking to avoid ''acquiring duplicate lock of same
type: "network driver"'' and potential deadlock. Also seems to fix LOR #063.
[1] This change does not solve problems if buffers are still in use when
unloading if_sk.ko. There is ongoing work which will address jumbogram
allocations in a more general way.
PR: kern/75677 (with changes, no mii fixes in here)
Tested by: net, Antoine Brodin (slightly different version)
Approved by: rwatson (mentor)
MFC after: 5 days
Obtained from: NetBSD if_sk.c rev. 1.11
* Take PHY out of reset for Yukon Lite Rev. A3.
Submitted by: postings on net@ in thread "skc0: no PHY found", 2005-02-22
Tested by: net
Approved by: rwatson (mentor)
MFC after: 5 days
if the interface is marked RUNNING.
Obtained from: NetBSD if_sk.c rev. 1.12
* Don't initialize the card (and start an autonegotiation) every time the IP
address changes. Makes 'dhclient sk0' invocations way faster and more
consistant. i.e. one DHCPREQUEST elicits the DHCPACK.
Obtained from: OpenBSD if_sk.c rev. 1.56
* Additional locking changes in sk_ioctl.
PR: kern/61296 should see improvements by the last two.
Approved by: rwatson (mentor)
MFC after: 5 days
doing that in bfe_stop().
This should fix a panic recently reported on -current occuring when taking
device down then up. In the original implementation, an "ifconfig bfe0 down"
triggers bfe_stop(), which also destroys all TX/RX descriptor dmamaps. Hence
the subsequent "ifconfig bfe0 up" would force the device to use those
already-released dmamap and thus panic the kernel.
PR: kern/77804
Submitted by: Frank Mayhar <frank at exit dot com>
Reviewed by: dmlb, sam (mentor)
Tested by: Phil <pcasidy at casidy dot com>, myself
MFC after: 1 week
session in tprintf(). SESSRELE() needs to properly dispose of the
sessions mutex.
Add sessrele() which does the proper cleanup and have SESSRELE() call it.
Use SESSRELE also in pgdelete().
Found by: Coverity (ID:526)
a given page and, if the pmap is the current pmap, write back the associated
cache line.
Use pmap_wb_page in pmap_qenter() instead of inconditionally
write back/invalidating the data cache.
o Use IP_NPX in preference to hard coded value to write 0 to clear busy#
o Use md macro for a full reset of the npx
o Use IRQ_NPX in preference to hard coded value for each platform.
# The other two ifdefs in this file are hard to remove
rman_resource_resournce_bound wrt end parameter. The end parameter
here was the same as the start. However, it should be start + count -
1, so make it that instead.
fedisableexcept(), and fegetexcept(). These two sets of routines
provide the same functionality. I implemented the former as an
undocumented internal interface to make the regression test easier to
write. However, fe(enable|disable|get)except() is already part of
glibc, and I would like to avoid gratuitous differences. The only
major flaw in the glibc API is that there's no good way to report
errors on processors that don't support all the unmasked exceptions.
