sidewaysintpr(). This increases the accuracy of the per-interval
counts when they are interpreted as rates. Repeated calls to alarm(n)
give an average interval that is about 2 ticks larger than n and has
a large variance. Periodic itimers normally get the average almost
right but have similarly large variance (due to scheduling delays).
Statistics utilities should use clock_gettime() to determine the
actual interval, but it is still useful to maximize the accuracy of
the interval, especially for cases like netstat -w where counts are
displayed so the program cannot hide the inaccuracy in a rate
conversion.
potential issues where the peer does not close, potentially leaving
thousands of connections in FIN_WAIT_2. This is controlled by a new sysctl
fast_finwait2_recycle, which is disabled by default.
Reviewed by: gnn, silby.
- BIOCGDIRECTION and BIOCSDIRECTION get or set the setting determining
whether incoming, outgoing, or all packets on the interface should be
returned by BPF. Set to BPF_D_IN to see only incoming packets on the
interface. Set to BPF_D_INOUT to see packets originating locally and
remotely on the interface. Set to BPF_D_OUT to see only outgoing
packets on the interface. This setting is initialized to BPF_D_INOUT
by default. BIOCGSEESENT and BIOCSSEESENT are obsoleted by these but
kept for backward compatibility.
- BIOCFEEDBACK sets packet feedback mode. This allows injected packets
to be fed back as input to the interface when output via the interface is
successful. When BPF_D_INOUT direction is set, injected outgoing packet
is not returned by BPF to avoid duplication. This flag is initialized to
zero by default.
Note that libpcap has been modified to support BPF_D_OUT direction for
pcap_setdirection(3) and PCAP_D_OUT direction is functional now.
Reviewed by: rwatson
loaded into the system.
Change wording of comments to reflect the fact we should unconditionally
use KVM if the -M option is used to specify a core file.
Add comments to document the fact that IPv6 multicast forwarding
information display still relies on KVM for gathering information.
Without -n, we now only print a "network name" without the prefix length
under the following conditions:
1) the network address and mask matches a classful network prefix;
2) getnetbyaddr(3) returns a network name for this network address.
With -n, we unconditionally print the full unabbreviated CIDR network
prefix in the form "a.b.c.d/p". 0.0.0.0/0 is still printed as "default".
This change is in preparation for changes such as equal-cost multipath, and
to more generally assist operational deployment of FreeBSD as a modern IPv4
router. There are currently no plans to backport this change.
Discussed on: freebsd-net
including to printf(). Using uintmax_t is also robust to further
extensions in both the C language and the bitwidth of kernel counters.
Tested on: i386 amd64 ia64
with FAST_IPSEC rather than the KAME IPSEC stack.
Note that the output of "netstat -s -p ipsec" differs depending on which
stack is compiled into the kernel since they each keep different stats.
This delta also adds the "esp", "ah", and "ipcomp" protocol stats, which
are also available when the kernel is compiled with the FAST_IPSEC stack
(e.g. "netstat -s -p esp").
Submitted by: Matt Titus <titus at nttmcl dot com>
MFC after: 3 days
kernel memory and not using sysctl. Previously, libmemstat was used
only for the live kernel via sysctl paths.
This results in netstat output becoming both more consistent between
core dumps and the live kernel, and also more information in the core
dump case than previously (i.e., mbuf cache information).
Statistics relating to sfbufs still rely on a kvm descriptor as they
are not currently exposed via libmemstat. netstat -m operating on a
core is still unable to print certain sfbuf stats available on the live
kernel.
MFC after: 1 week
replacement and has additional features which make it superior.
Discussed on: -arch
Reviewed by: thompsa
X-MFC-after: never (RELENG_6 as transition period)
a -B option which causes bpf peers to be printed. This option can be
used in conjunction with -I if information about specific interfaces
is desired. This is similar to what NetBSD added to their version of
netstat.
$ netstat -B
Pid Netif Flags Recv Drop Match Sblen Hblen Command
1137 lo0 p--s-- 0 0 0 0 0 tcpdump
205 sis0 -ifs-l 37331 0 1 0 0 dhclient
$
$ netstat -I lo0 -B
Pid Netif Flags Recv Drop Match Sblen Hblen Command
1174 lo0 p--s-- 0 0 0 0 0 tcpdump
$
-Add bpf.c which stores all the code for retrieving and parsing bpf
related statistics.
-Modify main.c to add support for the -B option and hook it into the
program logic.
-Add bpf.c to the build.
-Document this new functionality in the man page and bump the revision
date.
-Add prototype for bpf_stats function.
