Clang trunk recently gained this new warning, and complains about the
sizeof(trim->data) / sizeof(struct nvme_dsm_range) expression, since
the left hand side's element type (char) does not match the right hand
side's type. The byte buffer is unnecessary so we can remove it to clean
up the code and fix the warning at the same time.
No functional change.
Submitted by: James Clarke <jrtc27@jrtc27.com>
Reviewed by: imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D21912
It is typical to have one, but no longer true for multi-actuator HDDs
with separate LUN for each actuator.
MFC after: 4 days
Sponsored by: iXsystems, Inc.
This is a rework of r344701, that noticed that number of bytes passes to
8 bit sector count field gets truncated. First decision was to not pass
anything, since ATA specs define the field as N/A. But it appeared to be a
problem for some SAT devices, that require information about data transfer
to operate properly. Some additional investigation shown that it is quite
a common practice to set unused fields of ATA commands (fortunately ATA
specs formally allow it) to supply the information to SAT layer. I have
found SAS-SATA interposer that does not allow pass-through without it.
As side effect, reduce code duplication by removing ata_do_28bit_cmd()
function, replacing it with more universal ata_do_cmd().
MFC after: 1 week
Sponsored by: iXsystems, Inc.
XPT_DEV_ADVINFO call should be protected by the lock of the specific
device it is addressed to, not the lock of SES device. In some weird
case, probably with hardware violating standards, it sometimes caused
NULL dereference due to race.
To protect from it further, add lock assertion to *_dev_advinfo().
MFC after: 1 week
Sponsored by: iXsystems, Inc.
This makes the media check process asynchronous, so we no longer block
in cdstrategy() to check for media.
PR: 219857
Obtained from: ken
MFC after: 3 weeks
Even if we do not expect retries, we better be sure, since otherwise it
may result in use after free kernel panic. I've noticed that it retries
SCSI_STATUS_BUSY even with SF_NO_RECOVERY | SF_NO_RETRY.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
It allows to read and write block descriptors alike to mode page parameters.
It allows to change block size or short-stroke HDDs or overprovision SSDs.
Depenting on -P parameter the change can be either persistent or till reset.
In case of block size change device may need reformat after the setting.
In case of SSD overprovisioning format or sanitize may be needed to really
free the flash.
During implementation appeared that csio_encode_visit() can not handle
integers of more then 4 bytes, that makes 8-byte LBA handling awkward.
I had to split it into two 4-byte halves now.
MFC after: 1 week
Relnotes: yes
Sponsored by: iXsystems, Inc.
If not limited by write_same_max_lba option, split operation into several
2^^31 blocks chunks in a loop. For large disks it may take a while, so
setting write_same_max_lba may be useful to avoid timeouts.
While there, fix build with CAM_CTL_DEBUG.
MFC after: 2 weeks
The values to report can be set via LUN options. It can be useful for
testing, and also required for Drive Maintenance 2016 feature set.
MFC after: 2 weeks
CTL implements all defined feature sets except Drive Maintenance 2016,
which is not very applicable to such a virtual device, and implemented
only partially now. But may be it could be fixed later at least for
completeness.
MFC after: 2 weeks
ATA sanitize is functionally identical to SCSI, just uses different
initiation commands and status reporting mechanism.
While there, make kernel better handle sanitize commands and statuses.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
While for ATA disks resize is even more rare situation than for SCSI, it
may happen in case of HPA or AMA being used. Make ATA XPT report minor
IDENTIFY DATA change to upper layers with AC_GETDEV_CHANGED, and ada(4)
periph driver handle that event, recalculating all the disk properties and
signalling resize to GEOM. Since ATA has no mechanism of UNIT ATTENTIONs,
like SCSI, it has no way to detect that something has changed. That is why
this functionality depends on explicit reprobe via XPT_REPROBE_LUN call.
MFC after: 2 weeks
Relnotes: yes
Sponsored by: iXsystems, Inc.
In principle this should not matter as it's a union and they point to
the same memory location but based on the code above we should be
accessing .sata and not .ata.
Submitted by: arichardson
Reviewed by: scottl, imp
Obtained from: CheriBSD
MFC after: 1 week
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D21002
AMA replaced HPA in ACS-3 specification. It allows to limit size of the
disk alike to HPA, but declares inaccessible data as indeterminate. One
of its practical use cases is to under-provision SATA SSDs for better
reliability and performance.
While there, fix HPA Security detection/reporting.
MFC after: 2 weeks
Relnotes: yes
Sponsored by: iXsystems, Inc.
This was added for emulation of Linux's CDROMSUBCHNL, but allows
users with read access to a cd(4) device to overwrite kernel memory
provided that the driver detects some media present.
Reimplement CDROMSUBCHNL by bouncing the data from CDIOCREADSUBCHANNEL
through the linux_cdrom_subchnl structure passed from userspace.
admbugs: 768
Reported by: Alex Fortune
Security: CVE-2019-5602
Security: FreeBSD-SA-19:11.cd_ioctl
Use the cam_ed copy of ata_params rather than malloc and freeing
memory for it. This reaches into internal bits of xpt a little, and
I'll clean that up later.
Create ata_param_fixup
Create a common fixup routine to do the canonical fixup of the
ata_param fixup. Call it from both the ATA and the ATA over SCSI
paths.
Go ahead and completely fix the ata_params before calling the veto
function. This breaks nothing that uses it in the tree since
ata_params is ignored in storvsc_ada_probe_veto which is the only
in-tree consumer.
NANDFS has been broken for years. Remove it. The NAND drivers that
remain are for ancient parts that are no longer relevant. They are
polled, have terrible performance and just for ancient arm
hardware. NAND parts have evolved significantly from this early work
and little to none of it would be relevant should someone need to
update to support raw nand. This code has been off by default for
years and has violated the vnode protocol leading to panics since it
was committed.
Numerous posts to arch@ and other locations have found no actual users
for this software.
Relnotes: Yes
No Objection From: arch@
Differential Revision: https://reviews.freebsd.org/D20745
Since SES specs do not define mechanism to map enclosure slots to SATA
disks, AHCI EM code I written many years ago appeared quite useless,
that always bugged me. I was thinking whether it was a good idea, but
if LSI HBAs do that, why I shouldn't?
This change introduces simple non-standard mechanism for the mapping
into both AHCI EM and SES code, that makes AHCI EM on capable controllers
(most of Intel's) a first-class SES citizen, allowing it to report disk
physical path to GEOM, show devices inserted into each enclosure slot in
`sesutil map` and `getencstat`, control locate and fault LEDs for specific
devices with `sesutil locate adaX on` and `sesutil fault adaX on`, etc.
I've successfully tested this on Supermicro X10DRH-i motherboard connected
with sideband cable of its S-SATA Mini-SAS connector to SAS815TQ backplane.
It can indicate with LEDs Locate, Fault and Rebuild/Remap SES statuses for
each disk identical to real SES of Supermicro SAS2 backplanes.
MFC after: 2 weeks
SES specifications tell: "The Additional Element Status descriptors shall
be in the same order as the status elements in the Enclosure Status
diagnostic page". It allows us to question ELEMENT INDEX that is lower
then values we already processed. There are many SAS2 enclosures with
this kind of problem.
While there, add more specific error messages for cases when ELEMENT INDEX
is obviously wrong. Also skip elements with INVALID bit set.
MFC after: 2 weeks
When some type has 0 elements, saved_individual_element_index was set
to -1 on second type bump, since individual_element_index was not
restored after the first. To me it looks easier just to increment
saved_individual_element_index separately than think when to save it.
MFC after: 2 weeks
Do not allocate temporary buffer for attributes we are going to return
as-is, just make sure to NUL-terminate them. Do not zero temporary 64KB
buffer for CDAI_TYPE_SCSI_DEVID, XPT tells us how much data it filled
and there are also length fields inside the returned data also.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Add cam_sim_alloc_dev() as a wrapper to cam_sim_alloc() which takes
a device_t instead of the unit_number (which we can derive from the
dev again).
Add device_t sim_dev to struct cam_sim. It will be used to pass through
the bus for cases when both sides of CAM speak newbus already and we want
to link them (yet make the calls through CAM for now).
SDIO will be the first consumer of this. For that make use of
cam_sim_alloc_dev() in sdhci under MMCCAM.
This will also allow people to start iterating more on the idea
to newbus-ify CAM without changing 50+ device drivers from the start.
Also to be clear there are callers to cam_sim_alloc() which do not
have a device_t (e.g., XPT) or provide their own unit number so we cannot
simply switch the KPI entirely.
Submitted by: kibab (original idea, see https://reviews.freebsd.org/D12467)
Reviewed by: imp, chuck
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19746
Differentiate between PCI Express Endpoint devices and Root Complex
Integrated Endpoints in the nda driver. The Link Status and Capability
registers are not valid for Integrated Endpoints and should not be
displayed. The bhyve emulated NVMe device will advertise as being an
Integrated Endpoint.
Reviewed by: imp
Approved byL imp (mentor)
Differential Revision: https://reviews.freebsd.org/D20282
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
According to specs and common sense, all sense data reported in descriptor
format should be valid. But practice shows different, some devices return
descriptors with invalid data, resulting in error messages looking worse.
Decouple block/stream commands sense data and information field printing.
Looking on present specs, there are much more cases when those fields are
not related, and incomplete old code was not printing valid sense data and
leaving empty lines for invalid.
MFC after: 2 weeks
SDIO command CMD53 (IO_RW_EXTENDED) allows data transfers using blocks of 1-2048 bytes,
with a maximum of 511 blocks per request.
Extend mmc_data structure to properly describe such requests,
and initialize the new fields in kernel and userland consumers.
No actual driver changes happen yet, these will follow in the separate changes.
Reviewed by: bz
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D19779
Before this I suppose it was impossible load CAM-based NVMe as module.
Plus this appeared to be needed to build r345815 without NVMe driver.
MFC after: 2 weeks
