only support external PHYs (besides not connectable internal ones
which respond at the usual addresses, but which don't hurt if we
let them show up) and don't wedge when isolating PHYs. Actually,
this change special cases limiting PHYs to Am79C97{3,5,8}, for
which this driver doesn't implement swiching between the internal
and external PHYs, yet, and Am79C971, where isolating the external
PHY (at least in case it's a DP83840A) wedges the chip. Together
with sys/dev/mii/acphy.c rev. 1.21 this adds support for the
100baseFX port of AT-2700 series adaptors, which use two AC101,
one for the copper and one for the fibre port (there might be
variants which only use one PHY though).
- Fix a bug in the previous revision that prevented the address of
the used (external) PHY to be actually recorded.
- Don't bother to set if_mtu to ETHERMTU, ether_ifattach() does that.
MFC after: 1 week
via the PCN_CSR_MODE register. Along with sys/dev/mii/nsphy.c 1.26
this fixes the case of certain Am79c971-based HP cards and on-board
ones in IBM machines reporting link but not actually passing any
traffic. [1]
- Add support for the internal 10baseT PHY, which actually is used on
at least said HP cards (together with an external DP83840A in a
multiple PHYs configuration). With cards that don't make use of this
internal PHY it'll also show up in FreeBSD but not cause any harm.
This is still missing support for multiple PHYs configuration using
the internal 100baseTX and/or HomePNA PHYs together with external
PHYs or multiple external PHYs though.
- In pcn_ifmedia_upd() call pcn_reset() as otherwise the Am79C971 of
at least said HP cards can wedge when switching from the internal
10baseT PHY to the external PHY. This means that we need to also
initialize and possibly start the chip again in pcn_ifmedia_upd(),
which isn't that bad though as for setting the media port the chip
has to be powered down or stopped anyway and unlike documented
doesn't take effect until the next initialization.
PR: 27995, 25959, 72966 (likely) [1]
MFC after: 2 weeks
by this driver and largely are not even PCI devices in pcn_chipid.
- Use device_printf(9)/if_printf(9) rather than implementing their
functionality with printf(9).
- Sprinkle some const.
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
- Add locked versions of the init() and start() methods.
- Use callout_*() rather than timeout().
- Make the driver lock non-recursive.
- Push down locking in detach() and ioctl().
- Fix the tick routine to bail if the interface has been stopped and use
callout_drain() in detach() after the call to stop().
- Lock the driver lock in the ifmedia handlers.
Tested by: Ketrien I. Saihr-Kesenchedra ketrien at error404.nls.net
MFC after: 1 week
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
- Initialize sc->pcn_type during ATTACH as softc contents may not surivive
from PROBE.
- Print out chip-id to assist with ongoing pcn(4) debugging efforts.
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
if attach succeeded. device_is_alive just tells us that probe
succeeded. Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.
Symptoms of problem reported by: martin blapp
- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
- Remove locking of the softc in the attach method, instead depending on
bus_setup_intr being at the end of attach (delaying interrupt enable until
after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
in detach to only free resources that were allocated. This puts all
resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before. It was unnecessary
to move it. This reverts part of 1.88
- rl: move irq allocation before ether_ifattach. Problems might have been
caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
null pointer.
Reviewed by: imp, mdodd
