default we provide 16 interrupt sources for IRQs 0 through 15. However,
if the I/O APIC driver has already registered sources for any of those IRQs
then we will silently fail to register our own source for that IRQ.
Note that i386/isa/icu.h is now specific to the 8259A and no longer
contains any info relevant to APICs. Also note that fast interrupts no
longer use a separate entry point. Instead, both fast and threaded
interrupts share the same entry point which merely looks up the appropriate
source and passes control to intr_execute_handlers().
that provides methods via a PIC driver to do things like mask a source,
unmask a source, enable it when the first interrupt handler is added, etc.
The interrupt code provides a table of interrupt sources indexed by IRQ
numbers, or vectors. These vectors are what new-bus uses for its IRQ
resources and for bus_setup_intr()/bus_teardown_intr(). The interrupt
code then maps that vector a given interrupt source object. When an
interrupt comes in, the low-level interrupt code looks up the interrupt
source for the source that triggered the interrupt and hands it off to
this code to execute the appropriate handlers.
By having an interrupt source abstraction, this allows us to have different
types of interrupt source providers within the shared IRQ address space.
For example, IRQ 0 may map to pin 0 of the master 8259A PIC, IRQs 1
through 60 may map to pins on various I/O APICs, and IRQs 120 through
128 may map to MSI interrupts for various PCI devices.
the root path. This is reported to make non-PXE netbooting, such as
is used on sparc64 systems, work correctly when the TFTP server is
not the same as the root server.
PR: kern/57328
Submitted by: Per Kristian Hove <Per.Hove@math.ntnu.no>
header copy made on input path: this is now handled differently.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
is really EtherExpress or EEPro or what, but it does appear in a
couple of ethernet cards that have appeared recently on ebay. Silicom
appears to make these cards, and they have the 82595TX chipset in
them, and sometimes uarts. The ex driver needs some work to support
these cards, but I thought I'd get the device into pccarddevs.
The hardware driver decides the name under /dev/led and provides
the function to turn the lamp on/off.
All leds are serviced by a single timeout which runs at a basic rate
of hz/10.
The LED is controlled by ascii strings as follows.
0 Turn off.
1 Turn on.
f Flash: _-
f2 Flash: __--
f3 Flash: ___---
f4...f9 etc.
d%d Digits. "d12": -__________-_-______________________________
s%s String, roll your own:
'a-j' gives on for (1...10)/10 sec.
'A-J' gives on for (1...10)/10 sec.
'sAaAbBa': _-_--__-
m%s Morse
'.' dot
'-' dash
' ' letter space
'\n' word space
My mdoc skills do not reach to express that.
Add a sysctl declaration for hw.ata.atapi_dma, which had gone MIA (though
setting it in loader.conf still worked, it was not visible at runtime)
Approved by: sos
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
message encoding and decoding stuff into the base module. All of this
is accessed by several of the NgATM modules and putting this into
atmbase reduceds the memory footprint.
cr.isr sanity check. We actually encounter insanities, which very
likely means that the insanity check itself is insane. Remove an empty
comment while I'm at it.
directly on the radix tree and does not hold any routing table refernces.
This fixes the reference counting problems that manifested itself as a
panic during unmount of filesystems that were mounted by NFS over an
interface that had been removed.
Supported by: FreeBSD Foundation
idle. They figure out that we're idle fast enough that the cache pollution
introduces by scanning their run queue is more expensive than waiting
a little longer.
- Add kseq_setidle() to mark us as being idle. Use this in place of
kseq_find().
- Remove kseq_load_highest(), kseq_find() was the only consumer of this
interface. kseq_balance() has it's own customized version that finds the
lowest and highest loads simultaneously.
Continuously told that this would be faster by: terry
GEOM was not designed to handle media that does not have
a size. Blank CD's are of that type, so cheat and set the
media size to -1. This allows burning to work, but makes
GEOM issue outofrange reads that makes the ATAPI subsystem
spew out a few warnings. GEOM should be tought about this.
GEOM was not designed to handle changing the sectorsize
between opens. Writing multitack CD's with both audio and
data tracks needs to change sector size on the fly. We
cheat here and stuff the current sectorsize into GEOM
private internals. GEOM should grow some clean way for this.
