APIC Descriptor Table to enumerate both I/O APICs and local APICs. ACPI
does not embed PCI interrupt routing information in the MADT like the MP
Table does. Instead, ACPI stores the PCI interrupt routing information
in the _PRT object under each PCI bus device. The MADT table simply
provides hints about which interrupt vectors map to which I/O APICs. Thus
when using ACPI, the existing ACPI PCI bridge drivers are sufficient to
route PCI interrupts.
- The apic interrupt entry points have been rewritten so that each entry
point can serve 32 different vectors. When the entry is executed, it
uses one of the 32-bit ISR registers to determine which vector in its
assigned range was triggered. Thus, the apic code can support 159
different interrupt vectors with only 5 entry points.
- We now always to disable the local APIC to work around an errata in
certain PPros and then re-enable it again if we decide to use the APICs
to route interrupts.
- We no longer map IO APICs or local APICs using special page table
entries. Instead, we just use pmap_mapdev(). We also no longer
export the virtual address of the local APIC as a global symbol to
the rest of the system, but only in local_apic.c. To aid this, the
APIC ID of each CPU is exported as a per-CPU variable.
- Interrupt sources are provided for each intpin on each IO APIC.
Currently, each source is given a unique interrupt vector meaning that
PCI interrupts are not shared on most machines with an I/O APIC.
That mapping for interrupt sources to interrupt vectors is up to the
APIC enumerator driver however.
- We no longer probe to see if we need to use mixed mode to route IRQ 0,
instead we always use mixed mode to route IRQ 0 for now. This can be
disabled via the 'NO_MIXED_MODE' kernel option.
- The npx(4) driver now always probes to see if a built-in FPU is present
since this test can now be performed with the new APIC code. However,
an SMP kernel will panic if there is more than one CPU and a built-in
FPU is not found.
- PCI interrupts are now properly routed when using APICs to route
interrupts, so remove the hack to psuedo-route interrupts when the
intpin register was read.
- The apic.h header was moved to apicreg.h and a new apicvar.h header
that declares the APIs used by the new APIC code was added.
default we provide 16 interrupt sources for IRQs 0 through 15. However,
if the I/O APIC driver has already registered sources for any of those IRQs
then we will silently fail to register our own source for that IRQ.
Note that i386/isa/icu.h is now specific to the 8259A and no longer
contains any info relevant to APICs. Also note that fast interrupts no
longer use a separate entry point. Instead, both fast and threaded
interrupts share the same entry point which merely looks up the appropriate
source and passes control to intr_execute_handlers().
that provides methods via a PIC driver to do things like mask a source,
unmask a source, enable it when the first interrupt handler is added, etc.
The interrupt code provides a table of interrupt sources indexed by IRQ
numbers, or vectors. These vectors are what new-bus uses for its IRQ
resources and for bus_setup_intr()/bus_teardown_intr(). The interrupt
code then maps that vector a given interrupt source object. When an
interrupt comes in, the low-level interrupt code looks up the interrupt
source for the source that triggered the interrupt and hands it off to
this code to execute the appropriate handlers.
By having an interrupt source abstraction, this allows us to have different
types of interrupt source providers within the shared IRQ address space.
For example, IRQ 0 may map to pin 0 of the master 8259A PIC, IRQs 1
through 60 may map to pins on various I/O APICs, and IRQs 120 through
128 may map to MSI interrupts for various PCI devices.
Requested by: jhb
Initialize the real mode stack. This is needed at least for the return
address from the lcall.
Requested by: takawata
Fix style bugs in acpi_wakecode.S
Requested by: bde
Remove the kernel option now that we have the tunable.
to use the direct mapped KVA at KERNBASE to service the request. This also
allows pmap_mapdev() to be used for such addresses very early during the
boot process and might provide some small savings on KVA.
Reviewed by: peter
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
routines. Otherwise we run into trouble with speculative tlb preloads
on SMP systems. This effectively defeats Jeff's revision 1.438
optimization (for his pentium4-M laptop) in the SMP case. It breaks
other systems, particularly athlon-MP's.
the ACPI timer and we shouldn't do that if ACPI is already around to do
that for us.
- Set a description and tweak the order of checks in the probe function
to more closely match other PCI drivers.
This should probably be moved to sys/dev/piix/piix.c at some point and
turned on for all i386 kernels rather than just SMP ones.
enable strict checks of the AML. Our default behavior will be to relax
checks to work on as many platforms as possible. Also clean up and document
other ACPI options while I'm here.
Xcpustop(). %es is used in at least the call to savectx() when savectx()
calls bcopy(), so not loading it was fatal if a stop IPI interrupts
user mode.
This reduces bugs starting and stopping CPUs for debuggers. CPUs are
stopped mainly in kdb_trap() and cpu_reset(). At reset time there is
a good chance that all the CPUs are in the kernel, so the bug was
probably harmless then.
I changed. That is never a good sign.
1) only map 1 page at address zero, not 4096 pages
2) page 1 starts at address 4096 (PAGE_SIZE) not 4095 (PAGE_MASK). I
don't even want to think what the pte's looked like.
3) subtract the r/o page group start address from the end before
converting it to a count. Otherwise an extra page is mapped.
If you were affected by this, the symptoms of this was a hang at boot
after the spinner. Sorry folks. :-(
"You broke my laptop!" by: sam
use because a kernel thread is borrowing it. The borrowed page table
can change spontaneously, making any dependence on its continued use
subject to a race condition.
- _pmap_unwire_pte_hold() cannot use pmap_is_current(): If a change is
made to a page table page mapping for a borrowed page table, the TLB
must be updated.
In collaboration with: tegge
- Return NULL instead of returning memory outside of the stackgap
in stackgap_alloc() (FreeBSD-SA-00:42.linux)
- Check for stackgap_alloc() returning NULL in ibcs2_emul_find();
other calls to stackgap_alloc() have not been changed since they
are small fixed-size allocations.
- Replace use of strcpy() with strlcpy() in exec_coff_imgact()
to avoid buffer overflow
- Use strlcat() instead of strcat() to avoid a one byte buffer
overflow in ibcs2_setipdomainname()
- Use copyinstr() instead of copyin() in ibcs2_setipdomainname()
to ensure that the string is null-terminated
- Avoid integer overflow in ibcs2_setgroups() and ibcs2_setgroups()
by checking that gidsetsize argument is non-negative and
no larger than NGROUPS_MAX.
- Range-check signal numbers in ibcs2_wait(), ibcs2_sigaction(),
ibcs2_sigsys() and ibcs2_kill() to avoid accessing array past
the end (or before the start)
