a CD or DVD drive with a damaged disc often benefit from a shorter
timeout. Also, when retries are set to 0, an application is expecting
errors and recovering them so do not print the error into the log.
The number of expected errors can literally be in the hundreds of
thousands which significantly slows data recovery.
Reviewed by: ken@ (but quite some time ago).
14.00.00.01-fbsd.
Their description of the changes is as follows:
1. Copyright contents has been changed in all respective .c
and .h files
2. Support for WRITE12 and READ12 for direct-io (warpdrive only)
has been added.
3. Driver has added checks to see if Drive has READ_CAP_16
support before sending it down to the device.
If SPC3_SID_PROTECT flag is set in the inquiry data, the
device supports protection information, and must support
the 16 byte read capacity command, otherwise continue without
sending read cap 16. This will optimize driver performance,
since it will not send READ_CAP_16 to the drive which does
not have support of READ_CAP_16.
4. With new approach, "MPTIOCTL_RESET_ADAPTER" IOCTL will not
use DELAY() which is busy loop implementation.
It will use <msleep> (Better way to sleep without busy
loop). Also from the HBA reset code path and some other
places, DELAY() is replaced with msleep() or "pause()",
which is based on sleep/wakeup style calls. Driver use
msleep()/pause() instead of DELAY based on CAN_SLEEP/NO_SLEEP
flags to avoid busy loop which is not required all the
time.e.a
a. While driver is getting loaded, driver calls most of the
commands with NO_SLEEP.
b. When Driver is functional and it needs Reinit of HBA,
CAN_SLEEP flag is used.
5. <mpslsi> driver is not Endian safe. It will not work on Big
Endian machines like Sparc and PowerPC platforms because it
assumes it is running on a Little Endian machine.
Driver code is modified such way that it does not assume CPU
arch is Little Endian.
a. All places where Driver interacts from HBA to Host, it
converts Little Endian format to CPU format.
b. All places where Driver interacts from Host to HBA, it
converts CPU format to Little Endian.
6. Findout memory leaks in FreeBSD Driver and resolve those,
such as memory leak in targ's luns creation/deletion.
Also added additional checks to see memory allocation
success/fail.
7. Add loginfo prints as debug message, i.e. When FW sends any
loginfo, Driver should print those as debug message.
This will help for debugging purpose.
8. There is possibility to get config request timeout. Current
driver is able to detect config request timetout, but it does
not do anything on config_request timeout. Driver should
call mps_reinit() if any request_poll (which is called as
part of config_request) is time out.
9. cdb length check is required for 32 byte CDB. Add correct mpi
control value for 32 bit CDB as below while submitting SCSI IO
Request to controller.
mpi_control |= 4 << MPI2_SCSIIO_CONTROL_ADDCDBLEN_SHIFT;
10. Check the actual status of Message unit reset
(mps_message_unit_reset).Previously FreeBSD Driver just writes
MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET and never check the ack
(it just wait for 50 millisecond). So, Driver now check the
status of "MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET" after writing
it to the FW.
Now it also checking for whether doorbell ack uses msleep with
proper sleep flags, instead of <DELAY>.
11. Previously CAM does not detect Multi-Lun Devices. In order to
detect Multi-Lun Devices by CAM the driver needs following change
set:
a. There is "max_lun" field which Driver need to set based on
hw/fw support. Currently LSI released driver does not set
this field.
b. Default of "max_lun" should not be 0 in OS, but it is
currently set to 0 in CAM layer.
c. Export max_lun capacity to 255
12. Driver will not reset target info after port enable complete and
also do Device removal when Device remove from FW. The detail
description is as follows
a. When Driver receive WD PD add events, it will add all
information in driver local data structure.
b. Only for WD, we have below checks after port enable
completes, where driver clear off all information retrieved
at #1.
if ((sc->WD_available &&
(sc->WD_hide_expose == MPS_WD_HIDE_ALWAYS)) ||
(sc->WD_valid_config && (sc->WD_hide_expose ==
MPS_WD_HIDE_IF_VOLUME)) {
// clear off target data structure.
}
It is mainly not to attach PDs to OS.
FreeBSD does bus rescan as older Parallel scsi style. So Driver
needs to handle which Drive is visible to OS. That is a reason
we have to clear off targ information for PDs.
Again, above logic was implemented long time ago. Similar concept
we have for non-wd also. For that, LSI have introduced different
logic to hide PDs.
Eventually, because of above gap, when Phy goes offline, we
observe below failure. That is what Driver is not doing complete
removal of device with FW. (which was pointed by Scott)
Apr 5 02:39:24 Freebsd7 kernel: mpslsi0: mpssas_prepare_remove
Apr 5 02:39:24 Freebsd7 kernel: mpssas_prepare_remove 497 : invalid handle 0xe
Now Driver will not reset target info after port enable complete
and also will do Device removal when Device remove from FW.
13. Returning "CAM_SEL_TIMEOUT" instead of "CAM_TID_INVALID"
error code on request to the Target IDs that have no devices
conected at that moment. As if "CAM_TID_INVALID" error code
is returned to the CAM Layaer then it results in a huge chain
of errors in verbose kernel messages on boot and every
hot-plug event.
Submitted by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
MFC after: 3 days
the request up the tree in order to be on the safe side. Growing windows
in this case would mean to switch resources to positive decoding and
it's unclear how to correctly handle this. At least with ALi/ULi M5249
PCI-PCI bridges, this also just doesn't work out of the box.
Reviewed by: jhb
MFC after: 3 days
relocations are performed before the object's initializer is called.
When dlopen()ing an object, relocate the whole DAG rooted in the
object instead of only relocating the object itself and list of newly
loaded dependencies.
Reversed sequence currently can occur if the same object is a
dependency for both filtee and filter, since filtees are loaded
typically during the relocation processing, when some filter
dependencies might be already loaded but not relocated yet.
Reported and tested by: swills
Reviewed by: kan
MFC after: 1 week
and engine(3) are generated from these pod files during merge process and
we do not want to re-apply these changes over and over again.
Approved by: benl (maintainer, implicit)
usage on hosts using ZFS. The new line displays the total amount of RAM
used by the ARC along with the size of MFU, MRU, anonymous (in flight),
headers, and other (miscellaneous) sub-categories. The line is not
displayed on systems that are not using ZFS.
Reviewed by: avg, fs@
MFC after: 3 days
queue is empty or the firmware will go nuts.
PR: kern/167806
Tested by: osa@, Brandon Gooch (earlier version),
Bojan Petrovic (earlier version)
MFC after: 3 days
the TX queue is empty, there won't be a TX done notification, effectly
resulting in an mbuf leak. The correct way to handle this is to free
up mbufs on both BA and TX done notifications up to the last sent seqno.
Tested by: osa@
MFC after: 3 days
"gnusort". Most of the BSD sort development work was done by
Oleg Moskalenko <oleg.moskalenko@citrix.com>.
- GNU grep can be set to default by setting WITH_GNU_GREP. It will cause
BSD sort to be installed as "bsdsort".
Portbuild tested by: linimon
with AMPDU aggregate delimiters.
If there's an OFDM restart during an aggregate, the hardware ACKs
the previous frame, but communicates the RXed frame to the hardware
as having had CRC delimiter error + OFDM_RESTART phy error.
The frame however didn't have a CRC error and since the hardware ACKed
the aggregate to the sender, it thinks the frame was received.
Since I have no idea how often this occurs in the real world, add a
debug statement so trigger whenever this occurs. I'd appreciate an
email if someone finds this particular situation is triggered.
Bryan Cantrill implemented the equivalent of semi-log graph
paper for Dtrace so llquantize will use one logarithmic and
one linear scale.
Special thanks to Mark Peek for providing fix to an
assertion and to Fabian Keill for testing the port.
Illumos Revision: 13355:15b74a2a9a9d
Reference:
https://www.illumos/issues/905
Obtained from: Illumos
Tested by: Fabian Keill, mp
MFC after: 4 days