reordering won't make the actual write to be committed before marking
the coresponding extent as dirty.
It can be disabled in configuration file.
If BIO_FLUSH is not supported by the underlying file system we log a warning
and never send BIO_FLUSH again to that GEOM provider.
MFC after: 3 days
or mountpoint=legacy that have children datasets. This also fixes dataset
rename when receiving incremental snapshots as reported on freebsd-fs@
This assertion was made triggerable by opensolaris change #10196.
PR: bin/160400
Reviewed by: pjd
MFC after: 1 week
rather than the whole beacon interval.
The reference driver and Linux ath9k both choose 80% of the
beacon interval and they do it in the driver rather than
the HAL (Ath reference) or ath9k_hw (ath9k.)
This quietens stuck beacon conditions on my AR9220/AR9280
based NICs when a lot of burst broadcast/multicast traffic
is going on. It doesn't seem to annoy the earlier MACs as
much as the AR9280 and later one.
Obtained from: Linux ath9k, Atheros
local variable with a beacon interval of 100 TU. This never gets modified
if the beacon interval configuration changes.
This may have been correct in earlier times, but with the advent of
staggered beacons (which default to 1 / ATH_BCBUF beacon interval, so
25 TU here) this value is incorrect.
It is used to configure the default CABQ readytime. So here, the cabq
was being configured to be much greater than the target beacon timer
(TBTT.)
The driver should be configuring a cabq readytime value rather then
leaving it to the HAL to choose sensible defaults. This should be
done in the future - I'm simply trying to ensure sensible defaults
are chosen.
1. Allow the caller to select active mode.
2. Fix the envar logic so it *always* overrides the caller's flags.
3. Document the change from active to passive.
reads eating 100% CPU. Fix this by skipping select on STDIN after
reading EOF -- permanently if STDIN is not terminal and for one second
if it is.
Also after reading EOF from STDIN we have to pass it to the program
being scripted. The previous approach was to write zero bytes into the
pseudo-terminal. This does not work because zero-byte write does not
have any effect on read. Fix this by sending VEOF instead.
Submitted by: Ronald Klop <ronald-freebsd8@klop.yi.org>
Discussed with: kib, Chris Torek <chris.torek@gmail.com>
Approved by: kib
MFC after: 1 week
whle tracking down the system hang reported in kern/160662 and
corrected in revision 225806. The LOR is not the cause of the system
hang and indeed cannot cause an actual deadlock. However, it can
be easily eliminated by defering the acquisition of a buflock until
after all the vnode locks have been acquired.
Reported by: Hans Ottevanger
PR: kern/160662
but the use of fseek() means fetch(1) can't correctly resume a transfer
that was interrupted past the 2 GB mark.
Pointed out by: ache@
MFC after: 3 weeks
in append mode. Open it in read-write mode instead. Also move the
fseek up one level to cover the (unlikely but not impossible) case where
the server accepts ranges but does not send a Content-Size header.
PR: bin/117277
MFC after: 3 weeks
When a status pointer is passed in mfi_dcmd_command does not return an
errno (if the ioctl is successful), so move the test for NO_HW_PRESENT
outside of the error case. This should fix incorrect reporting for
systems with a dead or no battery.
Additionally, handle error codes other than NO_HW_PRESENT by omitting
the battery capacity display. LSI's supercap-based parts (CV series)
report their data using the same interface as battery-based parts,
except that they do not include the capacity stats (state of charge,
cumulative charge cycles, etc.)
Reviewd by: jhb, bz
Tested by: pluknet@, Garrett Cooper
PR: bin/160581
MFC after: 1 week
wdog_kern_pat() acquires eventhandler mutex, thus it cannot work in
kernel context (from where kdb_trap() runs).
The right way to fix this is both offering the
cpu-stop-on-panic-and-skip-locking logic and also a context for KDB
to officially run. We can re-enable this (or a similar) improvement
when these 2 patches hit the tree.
Sponsored by: Sandvine Incorporated
Discussed with: emaste, rstone
MFC after: immediately
build the ip_fw_pfil.c hooks and ipfw even in case of no-ip under the
assumption that the private L2 hook (which hopefully eventually will be a
pfil hook as well) can still be useful.
Allow building the module without inet as well.
Glanced at by: jhb
MFC after: 3 days
syscall exit path. Otherwise, if SIGTRAP is ignored, that tdsendsignal()
do not want to deliver the signal, and debugger never get a notification
of exec.
Found and tested by: Anton Yuzhaninov <citrin citrin ru>
Discussed with: jhb
MFC after: 2 weeks
kerberos libraries were not linked properly (missing dependencies),
which causes 3rd party applications linking to fail when --as-needed
ld flag is used. I also added the --no-undefined ld(1) flag to make
sure that there're no missing dependencies.
MFC after: 3 days
back-end features.
sys/dev/xen/netfront/netfront.c:
o Add xn_query_features() which reads the XenStore and
records the TSO, LRO, and chained ring-request support
of the backend.
o Rename xn_configure_lro() to xn_configure_features() and
use this routine to manage the setup of TSO, LRO, and
checksum offload.
o In create_netdev(), initialize if_capabilities and
if_hwassist to the capabilities found on all backends.
Delegate configuration of if_capenable and the TSO flag
if if_hwassist to xn_configure_features().
Reported by: Hugo Silva (fix inspired by patch provided)
Approved by: re
MFC after: 1 week
PV devices with the ioemu attribute set.
sys/dev/xen/netfront/netfront.c:
o If a mac address for the interface cannot be found
in the front-side XenStore tree, look for an entry
in the back-side tree. With ioemu devices, the
emulator does not populate the front side tree and
neither does Xend.
o Return an error rather than panic when an attach
attempt fails.
Reported by: Janne Snabb (fix inspired by patch provided)
PR: kern/154302
Approved by: re