sys/i386/i386/mem.c: only the super-user may open /dev/io
regardless of the device permissions (just 4 years late!).
Also, add cross-reference to i386_{get,set}_ioperm(2).
PR: kern/13359
Avoid using parenthesis enclosure macros (.Pq and .Po/.Pc) with plain text.
Not only this slows down the mdoc(7) processing significantly, but it also
has an undesired (in this case) effect of disabling hyphenation within the
entire enclosed block.
* Fix typo (defautls).
* Don't use hard sentence breaks in new text.
* Don't introduce the use of the second person (you).
* Use the standard "IMPLEMENTATION NOTES" section name instead of the
non-standard "TUNING".
Although it can go higher, it is not safe to so do on arrays with many
members. Compromise by adding a tunable, "hw.aac.iosize_max" that can be
set at boottime. Also document in the aac(4) manpage.
MFC after: 4 weeks
who didn't realize that DDB_UNATTENDED just sets its starting
value.
This change is over 5 years late, and documents the original
semantics of debug.debugger_on_panic, which may have been changed
by the (again undocumented) change in rev 1.44 of kern_shutdown.c.
net.link.ether.bridge_refresh variables. While I'm here, try to
make some of the markup on this page more consistent with the
new (markup-reviewed) content.
PR: 22060
Reviewed by: ru (for markup, on an earlier version of this delta)
MFC after: 2 days
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
the SYNOPSIS hasn't had an example number of devices since rev 1.2 which
was over 5 and a half years ago, so remove a sentence claiming that the
example in the SYNOPSIS limited bpf to 16 devices.
MFC after: 3 days
cd src/share; find man[1-9] -type f|xargs perl -pi -e 's/[ \t]+$//'
BTW, what editors are the culprits? I'm using vim and it shows
me whitespace at EOL in troff files with a thick blue block...
Reviewed by: Silence from cvs diff -b
MFC after: 7 days
spdadd A B -P in ipsec esp/tunnel/C-D/use ah/tunnel/C-D/require;
does not work due to 1-bit validation bit we are using with inbound
policy checking.
Submitted by: itojun
Obtained from: KAME
MFC after: 1 week
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
despite the fact that most people want to set exactly the same settings
regardless of which card they have. It has been repeatidly suggested
that this configuration should be done via ifconfig. This patch
implements the required functionality in ifconfig and add support to the
wi and an drivers. It also provides partial, untested support for the
awi driver.
PR: 25577
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
indicator are treated as strings, so "-offset 0" will set the offset
to the width of the string "0", as opposed to "no offset".
TIP: if offset is not needed, the -offset clause may be omitted.
on certain types of SOCK_RAW sockets. Also, use the ip.ttl MIB
variable instead of MAXTTL constant as the default time-to-live
value for outgoing IP packets all over the place, as we already
do this for TCP and UDP.
Reviewed by: wollman
and add a sysctl to pppoe to activate non standard ethertypes
so that idiot ISPs (apparently in France) who use
equipment from idiot suppliers (rumour says 3com)
who use nonstandard ethertypes can still connect.
"yep, sure we do pppoe, we use a different identifier to that dictated in
the standard, but sure it's pppoe!"
sysctl -w net.graph.stupid_isp=1 enables the changeover.
packet flow into two unidirectional flows.
Part of a suite of nodes developed for packet flow control.
More to follow as I have time to port them to 5.x or
as others do so. The ipfw node will be the hardest..
Submitted by: "Vitaly V. Belekhov" <vitaly@riss-telecom.ru>
to be the same as -ragged in the current implementation) to
-ragged. With mdocNG, -filled displays produce the correct
output, formatted and justified to both margins.
(e.g. ethernet nodes are persistent until you rip out the hardware)
Use this support in the ethernet and sample nodes.
Add some more abstraction on the 'item's so that node and
hook reference counting can be checked easier.
Slight man page correction.
Make pppoe type dependent on ethernet type.
Clean up node shutdown a little.
Move a mutex from MTX_SPIN to MTX_DEF (oops)
Fix small ref-counting bug.
remove warning on one2many type.
The new method is 'flood' (in addition to the old round-robin)
in which incoming packets are sent to more than one outgoing hook.
(I'm not sure what Rogier is using this for but it seems generally useful
and isn't much extra)
Submitted by: Rogier R. Mulhuijzen (drwilco@drwilco.net )
This version is functional and is aproaching solid..
notice I said APROACHING. There are many node types I cannot test
I have tested: echo hole ppp socket vjc iface tee bpf async tty
The rest compile and "Look" right. More changes to follow.
DEBUGGING is enabled in this code to help if people have problems.
format version number. (userland programs should not need to be
recompiled when the netgraph kernel internal ABI is changed.
Also fix modules that don;t handle the fact that a caller may not supply
a return message pointer. (benign at the moment because the calling code
checks, but that will change)
This clears out my outstanding netgraph changes.
There is a netgraph change of design in the offing and this is to some
extent a superset of soem of the new functionality and some of the old
functionality that may be removed.
This code works as before, but allows some new features that I want to
work with and evaluate. It is the basis for a version of netgraph
with integral locking for SMP use.
This is running on my test machine with no new problems :-)
While here, I also updated the kernel config style, although I wouldn't
recommend doing this for the whole of section 4 yet, since our kernel
config style is still in a state of flux.
Replace all in-tree uses with <sys/mouse.h> which repo-copied a few
moments ago from src/sys/i386/include/mouse.h by peter.
This is also the appropriate fix for exo-tree sources.
Put warnings in <machine/mouse.h> to discourage use.
November 15th 2000 the warnings will be converted to errors.
January 15th 2001 the <machine/mouse.h> files will be removed.
Replace all in-tree uses with necessary subset of <sys/{fb,kb,cons}io.h>.
This is also the appropriate fix for exo-tree sources.
Put warnings in <machine/console.h> to discourage use.
November 15th 2000 the warnings will be converted to errors.
January 15th 2001 the <machine/console.h> files will be removed.
of the Am79c973 with "AlertIT Technology," whatever that is. Also mention
support for the PCnet/FAST III cards in the documentation. The
PCnet/FAST III chips have integrated 10/100 PHYs.
this just involves adding the chip ID to the supported list: the PCnet/PRO
is compatible with the PCnet/FAST+ and friends and should "just work"
with this driver.
Also try to handle mbuf allocation failures in the receive handler
more gracefully.
Remove the entire copy of ip_fw.h and just point readers at it as it
gets out of date..
Add mentions of dummynet and the fwd actions.
Still to do: Whoever did the 'stateful' stuff might mention it..
Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.
configure FreeBSD so that various databases such as passwd and group can be
looked up using flat files, NIS, or Hesiod.
= Hesiod has been added to libc (see hesiod(3)).
= A library routine for parsing nsswitch.conf and invoking callback
functions as specified has been added to libc (see nsdispatch(3)).
= The following C library functions have been modified to use nsdispatch:
. getgrent, getgrnam, getgrgid
. getpwent, getpwnam, getpwuid
. getusershell
. getaddrinfo
. gethostbyname, gethostbyname2, gethostbyaddr
. getnetbyname, getnetbyaddr
. getipnodebyname, getipnodebyaddr, getnodebyname, getnodebyaddr
= host.conf has been removed from src/etc. rc.network has been modified
to warn that host.conf is no longer used at boot time. In addition, if
there is a host.conf but no nsswitch.conf, the latter is created at boot
time from the former.
Obtained from: NetBSD
