type of software interrupt. Roughly, what used to be a bit in spending
now maps to a swi thread. Each thread can have multiple handlers, just
like a hardware interrupt thread.
- Instead of using a bitmask of pending interrupts, we schedule the specific
software interrupt thread to run, so spending, NSWI, and the shandlers
array are no longer needed. We can now have an arbitrary number of
software interrupt threads. When you register a software interrupt
thread via sinthand_add(), you get back a struct intrhand that you pass
to sched_swi() when you wish to schedule your swi thread to run.
- Convert the name of 'struct intrec' to 'struct intrhand' as it is a bit
more intuitive. Also, prefix all the members of struct intrhand with
'ih_'.
- Make swi_net() a MI function since there is now no point in it being
MD.
Submitted by: cp
(a NetBSD port for NEC PC-98x1 machines). They are ncv for NCR 53C500,
nsp for Workbit Ninja SCSI-3, and stg for TMC 18C30 and 18C50.
I thank NetBSD/pc98 and bsd-nomads people.
Obtained from: NetBSD/pc98
write caching is disabled on both SCSI and IDE disks where large
memory dumps could take up to an hour to complete.
Taking an i386 scsi based system with 512MB of ram and timing (in
seconds) how long it took to complete a dump, the following results
were obtained:
Before: After:
WCE TIME WCE TIME
------------------ ------------------
1 141.820972 1 15.600111
0 797.265072 0 65.480465
Obtained from: Yahoo!
Reviewed by: peter
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.
Submitted by: dfr
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
also mention the peripheral name, bus, target and lun of the device we
attempted to put in that slot. This gives the user a little more
information about what is going on.
Tested by: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
Discussed with: gibbs
for the Quantum "MAVERICK 540S" and "LPS525S".
Also, add common string variables, since we seem to have a few Quantum and
Micropolis drives in here.
Fix the 'quantum' variable usage in scsi_all.c that likely got broken when
someone staticized things in cam_xpt.c. (That particular problem would
cause Quantum Fireball ST drives to not get spun up if they were not
already spinning.)
Submitted by: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
Make the umass driver depend on this module.
Makes it possible to compile the kernel without SCSI support and load it
when for example a USB floppy is conencted.
to be obeying the original spec as to what the numeric value means.
Temperature flags are unaffected- these are still the 'pseudo-thermometers'
and overtemp/undertemp warnings will be caught and translated to SES objects
here.
PR: 20475
related patches. These include:
* Mode page editting can be scripted. This involves two
things: first, if stdin is not a tty, changes are read from
stdin rather than invoking $EDITOR. Second, and more
importantly, not all modepage entries must be included in the
change set. This means that camcontrol can now gracefully handle
more intrusive editting from the $EDITOR, including removal or
rearrangement of lines. It also means that you can do stuff
like:
# echo "WCE: 1" | camcontrol modepage da3 -m 8 -e
# newfs /dev/da3
# echo "WCE: 0" | camcontrol modepage da3 -m 8 -e
* Range-checking on user-supplied input values. modeedit.c now
uses the field width specifiers to determine the maximum
allowable value for a field. If the user enters a value larger
than the maximum, it clips the value to the max and warns the
user. This also involved patching cam_cmdparse.c to be more
consistent with regards to the "count" parameter to arg_put
(previously is was the length of strings and 1 for all integral
types). The cam_cdbparse(3) man page was also updated to reflect
the revised semantics.
* In the process, I removed the 64 entry limit on mode pages (not
that we were even close to hitting that limit). This was a nice
side-effect of the other changes.
* Technically, the new mode editting functionality allows editting
of character array entries in mode pages (type 'c' or 'z'),
however since buff_encode doesn't grok them it is currently
useless.
* Camcontrol gained two new options related to mode pages: -l and
-b. The former lists all available mode pages for a given
device. The latter forces mode page display in binary format
(the default when no mode page definition was found in
scsi_modes).
* Added support for mode page names to scsi_modes. Allows names to
be displayed alongside mode numbers in the mode page
listing. Updated scsi_modes to use the new functionality. This
also adds the semicolon into the scsi_modes syntax as an
optional mode page definition terminator. This is needed to name
pages without providing a page format definition.
* Updated scsi_all.h to include a structure describing mode page
headers.
* Added $FreeBSD$ line to scsi_modes.
Inspired by: dwhite
Reviewed by: ken
Clean up the comments related to the high speed
sync rate table for SPI.
scsi_message.h:
Bring in some SCSI3 message terminology. All SCSI2 names
are still preserved for backwards compatibility.
Bring back the CAM_NEGOTIATE ccb flag. This flag indicates
that SPI transfer negotiation should occur concurrently with the
execution of this CCB. The flag is not yet used by the XPT but
is required for proper support of multi-initiator configurations
where topology scans cannot rely on a bus reset to invalidate
prior negotiations.
cam_xpt.c:
Don't allow DT transmission rates to be specified for devices
that don't have the DT feature listed in their inquiry data.
CAM_TAG_ACTION_VALID and CAM_DIR_MASK). Remove redundant
CAM_DEBUG line. Spiff up CAM_DEBUG printout for commands
and move the printout up to the top where we can see it,
even for the pending_ua/pending_ca cass. Add missing
newline in a CAM_DEBUG.
to splx(s) if cam_extend_get fails and we return ENXIO, reset ccb flags
when we push ATIOs back to the SIM, do some data increment fixes, set
priority of command based on whether CAM_DIS_DISCONNECT is set and related
changes).
Add in some more CAM_DEBUG_PERIPH debug statements and also add in support
for TARGIODEBUG which then will enable or disable CAM_DEBUG_PERIPH tracing
for an instance.
CAPACITY operation. SCSI-3 mandates this to be 2048, but some older
drives like my old Plasmon CD-R report weird numbers between 2048 and
up to 2352 bytes depending on the mode of the last track etc. This in
turn confuses stuff like the slice code since it refuses to work with
devices that do not have a blocksize which is a multiple of 512 bytes.
Reviewed by: ken
libcam/Makefile: Add scsi_da.c to libcam for the new
scsi_format_unit() function.
camcontrol.8: Update the man page for the new format
functionality, and take out the examples section
describing how to do it with 'camcontrol cmd'.
camcontrol.c: New format functionality. Note that unlike the
rest of the camcontrol subcommands, this one is
interactive by default. Because of the potential
destructiveness of the format command, I thought
it necessary to get confirmation from the user
before spamming a disk. You can disable the
interactive behavior, and the status meter with
command line arguments.
scsi_da.c: Add the new scsi_format_unit() cdb building
function and use #ifdef _KERNEL to make this file
compile in both the kernel and userland. The
format unit function is currently only defined in
the non-kernel case, because nothing in the kernel
is using it. If that changes, it should be
un-ifdefed and compiled in both cases.
scsi_da.h: New function declaration, CDB structure and format
data structures.
Thanks to Nick Hibma for providing some valuable input on these changes.
to various pmap_*() functions instead of looking up the physical address
and passing that. In many cases, the first thing the pmap code was doing
was going to a lot of trouble to get back the original vm_page_t, or
it's shadow pv_table entry.
Inspired by: John Dyson's 1998 patches.
Also:
Eliminate pv_table as a seperate thing and build it into a machine
dependent part of vm_page_t. This eliminates having a seperate set of
structions that shadow each other in a 1:1 fashion that we often went to
a lot of trouble to translate from one to the other. (see above)
This happens to save 4 bytes of physical memory for each page in the
system. (8 bytes on the Alpha).
Eliminate the use of the phys_avail[] array to determine if a page is
managed (ie: it has pv_entries etc). Store this information in a flag.
Things like device_pager set it because they create vm_page_t's on the
fly that do not have pv_entries. This makes it easier to "unmanage" a
page of physical memory (this will be taken advantage of in subsequent
commits).
Add a function to add a new page to the freelist. This could be used
for reclaiming the previously wasted pages left over from preloaded
loader(8) files.
Reviewed by: dillon
Add a SA_QUIRK_NO_MODESEL type and use it for the OnStream real SCSI
device (not the broken one). This one is still broken in that it can't
be set to the same fixed block size it reports [ unflattering comments
about this company elided ].
If we're unable to set buffered mode on, complain, but drive on. It's
not a fatal error to not be in buffered mode.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
