- Enable KX and UX bits on CPU startup for non-boot CPUs
- Keep the KX bit when in userspace - XTLB handler needs it to access
PCPU data
- revert r210638 partly - we don't need to enable KX on kernel entry
now
Reviewed by: jmallett, imp
library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
which improperly uses an evaluation board's board number and breaks board
detection at runtime. This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO
ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
structures where possible (it would be advisable to use the Simple Executive
API to set the PIO mode, too, but that is not done presently.) Also use
structures from FreeBSD's ATA layer rather than structures copied from
Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
and writes to 64-bit addresses and use its macros for various device
addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
Cavium-provided code originally written for Linux. Also make it use the
same simplified test that the Simple Executive and Linux both use rather
than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
the kernel, rather than assuming we know which addresses we can steal.
NB: This may reduce the amount of RAM the kernel reports you as having if
you are leaving large temporary allocations made by U-Boot allocated
when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes
Ethernet interface naming from rgmxN to octeN. The new driver has vast
improvements over the old one, both in performance and functionality, but
does still have some features which have not been ported entirely and there
may be unimplemented code that can be hit in everyday use. I will make
every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
executive-config.h or cvmx-config.h. In the future we may want to
revert part of these changes and supply executive-config.h and
cvmx-config.h and access to the options contained in those files via
kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
of the USB PID.
am now able to run 32 cores ok.. but I still will hang
on buildworld with a NFS problem. I suspect I am missing
a patch for the netlogic rge driver.
JC check and see if I am missing anything except your
core-mask changes
Obtained from: JC
o) Remove NBPG, PGOFSET and PGSHIFT. Use the standard names.
o) Remove some unused macros and move things from param.h to vmparam.h that
belong in the latter. (Actually, all of the kernel segment values, virtual
addresses, etc., belong in one place, but this is a step in the right
direction.)
same time.
o) Remove some unused trivial uart functions from octeon_machdep now that the
uart part is fully working and they are unused.
o) Use __func__ instead of __FUNCTION__.
o) Use intr_*() instead of other routines that do the same thing.
o) Remove some duplicate printfs from the Octeon port, as well as duplicate
setting of Maxmem.
o) Use the right frequency divider on Octeon.
o) Use PCPU_GET(cpuid) consistently to get the cpuid of the running core.
o) Remove some unused macros in the Octeon port.
o) Use mips_sync() around use of the global dpcpu, whose value may not be
visible to APs at first.
o) When loading the first thread's stack, use macros to make the code correct
for n64 as well.
o) Remove stub, do-nothing FAU init/enable/disable functions from the RGMX
driver.
The platform that supports SMP currently is a SWARM with a dual-core Sibyte
processor. The kernel config file to use is SWARM_SMP.
Reviewed by: imp, rrs
