updated
ZFS already supports storing the vdev FRU in a vdev property. There
is code in libzfs to work with this property, and there is code in
the zfs-retire FMA module that looks for that information. But there
is no code actually setting or updating the FRU.
To address this, ZFS is changed to send a handful of new events
whenever a vdev is added, attached, cleared, or onlined, as well
as when a pool is created or imported.
Note that syseventd is not currently available on FreeBSD and thus
some work is needed to actually support the new ZFS events (e.g. in
zfsd) to actually use this capability, this changeset is mostly a
diff reduction from upstream.
illumos/illumos-gate@1437283407
Illumos issues:
5997 FRU field not set during pool creation and never updated
https://www.illumos.org/issues/5997
* yes, when a "sta disconnect" message comes through we should, like,
disconnect things. We're not currently generating beacon miss messages,
and net80211 isn't disconnecting things via software beacon miss receive.
Tested:
* RTL8712, cut 3, STA mode
Formally pair store_rel(&smp_started) with load_acq(&smp_started).
Similarly to x86, this change is mostly a NOP due to the kernel
being run in total store order.
MFC after: 1 week
* use an ath/iwn style debug bitmap - it's still global rather than per-device,
but it's better than debug levels
* disable bgscan - it just makes things unstable/unpredictable for now.
Tested:
* if_rsu - RTL8712 cut 3, STA mode
drivers into the revived sys/sparc64/pci/ofw_pci.c, previously already
serving a similar purpose. This has been done with sun4v in mind, which
explains a) the otherwise not that obvious scheme employed and b) why
reusing sys/powerpc/ofw/ofw_pci.c was even lesser an option.
- Add a workaround for QEMU once again not emulating real machines, in
this case by not providing the OFW_PCI_CS_MEM64 range. [1]
Submitted by: jhb [1]
MFC after: 1 week
In r286570 (MFV of r277426) an unprotected write to b_flags to
set the compression mode was introduced. This would open a race
window where data is partially decompressed, modified, checksummed
and written to the pool, resulting in pool corruption due to the
partial decompression.
Prevent this by reintroducing b_compress
illumos/illumos-gate@d4cd038c92
Illumos issues:
6214 zpools going south
https://www.illumos.org/issues/6214
Rewrite the ZFS prefetch code to detect only forward, sequential
streams.
The following kstats have been added:
kstat.zfs.misc.arcstats.sync_wait_for_async
How many sync reads have waited for async read
to complete. (less is better)
kstat.zfs.misc.arcstats.demand_hit_predictive_prefetch
How many demand read didn't have to wait for I/O
because of predictive prefetch. (more is better)
zfetch kstats have been similified to hits, misses, and max_streams,
with max_streams representing times when we were not able to create
new stream because we already have the maximum number of sequences
for a file.
The sysctl variable/loader tunable vfs.zfs.zfetch.block_cap have been
replaced by vfs.zfs.zfetch.max_distance, which controls maximum bytes
to prefetch per stream.
illumos/illumos-gate@cf6106c8a0
Illumos ZFS issues:
5987 zfs prefetch code needs work
https://www.illumos.org/issues/5987
The pci bus driver handles the power state, it also manages
configuration state saving and restoring for its child devices. Thus a
PCI device driver does not have to worry about those things. In fact, I
observe a hard system hang when trying to suspend a system with active
radeonkms driver where both the bus driver and radeonkms driver try to
do the same thing. I suspect that it could be because of an access to a
PCI configuration register after the device is placed into D3 state.
Reviewed by: dumbbell, jhb
MFC after: 13 days
Differential Revision: https://reviews.freebsd.org/D3561
All requests arriving for processing after OFFLINE flag set are rejected
with BUSY status. Races around OFFLINE flag setting are closed by calling
taskqueue_drain_all().
in the routine, which queues an ERROR chunk, instead on relyinh
on the callers to do so. Since one caller missed this, this actially
fixes a bug.
MFC after: 1 week
running thread.
It is currently implemented only on amd64 and i386; on these
architectures, it is implemented by raising an NMI on the CPU on which
the target thread is currently running. Unlike stack_save_td(), it may
fail, for example if the thread is running in user mode.
This change also modifies the kern.proc.kstack sysctl to use this function,
so that stacks of running threads are shown in the output of "procstat -kk".
This is handy for debugging threads that are stuck in a busy loop.
Reviewed by: bdrewery, jhb, kib
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3256
since on amd64 the first argument to a function is generally not on the
stack.
Revert an old DTrace bug fix to some code that assumed that
sizeof(struct amd64_frame) == 16.
Reviewed by: jhb, kib
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3255
5930 fasttrap_pid_enable() panics when prfind() fails in forking process
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Gordon Ross <gordon.ross@nexenta.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Author: Bryan Cantrill <bryan@joyent.com>
illumos/illumos-gate@9df7e4e12e
The only operation which is prevented by the hold is the kernel stack
swapout for the faulted thread, which should be fine to allow.
Remove useless checks for NULL curproc or curproc->p_vmspace from the
trap_pfault() wrappers on x86 and powerpc.
Reviewed by: alc (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
CTL HA functionality was originally implemented by Copan many years ago,
but large part of the sources was never published. This change includes
clean room implementation of the missing code and fixes for many bugs.
This code supports dual-node HA with ALUA in four modes:
- Active/Unavailable without interlink between nodes;
- Active/Standby with second node handling only basic LUN discovery and
reservation, synchronizing with the first node through the interlink;
- Active/Active with both nodes processing commands and accessing the
backing storage, synchronizing with the first node through the interlink;
- Active/Active with second node working as proxy, transfering all
commands to the first node for execution through the interlink.
Unlike original Copan's implementation, depending on specific hardware,
this code uses simple custom TCP-based protocol for interlink. It has
no authentication, so it should never be enabled on public interfaces.
The code may still need some polishing, but generally it is functional.
Relnotes: yes
Sponsored by: iXsystems, Inc.
