These are 10/100 only NICs found on the IBM Thinkpad R40E and
G40. These seem to be based on the BCM5705 MAC but with a PHY
that doesn't support 1000Mbps modes.
Submitted by: Igor Sviridov <sia@nest.org>
- 5705 doesn't support jumbo frames
- Statistics must be read from registers
- RX return ring must be capped at 512 entries
- Omit initialization of certain device blocks
- Acknowledge link change interrupts by setting the 'link changed'
bit in the status register (used to have no effect)
- Remember to toggle the MI completion bit too
- Set the mbuf low watermark differently (on-chip memory buffers,
not BSD mbufs)
- Don't enable Ethernet@WireSpeed feature for certain 5705 chip revs
- Add additional PCI IDs for 5705 and 5782 parts
- Add a forgotten 5704 PCI ID
Most changes ripped kicking and screaming from the Broadcom linux driver.
Thanks to Paul Saab for sanity testing. (My lack of sanity has been
confirmed.)
patch workarounds for each phy revision.
Obtained from: NetBSD & Broadcom Linux driver
- Disable AUTOPOLL when accessing the PHY as it may cause PCI errors.
Obtained from: NetBSD
- Check the UPDATED bit in the status block so the driver knows
that the status block as indeed changed since the last access.
Broadcom documentation states drivers should unset the UPDATED/CHANGED
bits after reading them.
- When changing media types, first loop the phy then set the media.
Broadcom documentation and Linux drivers do this and I observed
much better handling of link after this change.
- Broadcom documentation states that for 1000BaseT operation,
autonegotiation must be enabled. Fix hard coding of media so that
the driver only advertises 1000BaseT as the supported media type
and enable autonegotition.
- Only set Master/Slave on the 5701.
Obtained from Broadcom Linux driver.
cards to test; however the submitter reports that this patch works
with the on-board interface on the IBM x235 server.
Submitted by: Jung-uk Kim <jkim@niksun.com>
MFC after: 1 month
when this is needed. Work around bogus second PHY in the DFE-580 card
via a change in the if_ste.c driver.
Suggested by: jdp
Reviewed by: jdp
MFC after: 3 days
internal PHY on the 3COM 3C905B and 3C905C parts, however I've rigged it so
that xlphy (aka exphy) takes precedence for the time being.
If people try this with their xl cards and decide that it's a better choice,
we can switch this later.
This is the PHY used in various iMacs and possibly other GMAC-equipped
Macintoshes with 10/100 PHYs (the ones with 10/100/1000 appear to use brgphy).
Obtained from: NetBSD
well as is, so - just fetch current status upon MII_TICK.
Also do IFM_INST verification at the top of *_service() then doing it
separately for every case in switch.
acphy: do not read MII_ACPHY_DIAG twice, there is nothing latching.
qsphy: always fetch actual link status from MII_QSPHY_PCTL.
MFC after: 1 week
Rename mii_phy_auto_stop() mii_phy_down().
Introduce mii_down(), use it from nge. Do not indirect it to 19 identical
case's in 19 switchstatements like NetBSD did.
Rev 1.56 of if_dc.c removed calls to mii_pollstat() from the dc_tick()
routine. dc_tick() is called regularly to detect link up and link down
status, especially when autonegotiating.
The expectation was that mii_tick() (which is still called from dc_tick())
would update status information automatically in all cases where it would
be sensible to do so.
Unfortunately, with authentic 21143 chips this is not the case, and
the driver never successfully autonegotiates. This is because (despite
what it says in the 21143 manual) the chip always claims that link is not
present while the autonegotiation enable bit is set. Autonegotation takes
place and succeeds, but the driver tests the link bits before it switches
off the autonegotiation enable bit, and success is not recognised.
The simplest solution is to call dcphy_status() more often for MII_TICK
calls by dropping out of the switch statement instead of exiting when
we are autonegotiating and link appears to not be present. When
autonegotiation succeeds, dcphy_status() will note the speed and fdx/hdx
state and turn off the autonegotiation enable bit. The next call to
dcphy_status() will notice that link is present, and the dc driver code
will be notified.
Macronix chips also use this code, but implement link detection as
described in the manual, and hence don't need this patch. However, tests
on a Macronix 98715AEC-C show that it does not adversely affect them.
This could be done better but is the minimal effective change, and most
closely mimics what was happening prior to rev 1.56 of if_dc.c. (Actually
I also deleted a small amount of unnecessary code while I was in the area.)
Reviewed by: wpaul
doesn't support NWAY, the RealTek PHY (both the integrated ones on 8139
chips and the RTL8201L 10/100 PHY) will not report the link speed via
the ANLPAR or BMSR registers. For the 8201L, we need to look in magic
vendor-specific PHY register 0x19. For the 8139 MAC+PHY combo, we have
to be able to test the RL_MEDIASTAT register.
The changes to rlphy.c are based largely on the patch from PR 30836,
however I tried to eliminate some magic numbers by creating an entry
for the 8201 PHY in miidevs.
Also updated if_rl.c to allow the rlphy driver to read the RL_MEDIASTAT
register via the rl_miibus_readreg() routine.
with an ifnet structure (so device_get_softc will get one).
If memory allocation fails in mii_phy_probe, don't just march ahead into
a panic- return ENOMEM.
MFC after: 1 week
. Make internal service routines static.
. Use a consistent ordering of checks in MII_TICK. Do the work in the
mii_phy_tick() subroutine if appropriate.
. Call mii_phy_update() to trigger the callbacks.
