o Make debugging code conditional upon KDB instead of DDB.
o Call kdb_alt_break() instead of db_alt_break().
o Call kdb_enter() instead of breakpoint().
o Call kdb_enter() instead of Debugger().
o Don't make such calls conditional upon KDB instead of DDB because
they're already conditional upon EN_DEBUG.
o Use kdb_alt_break() to handle the alternate break sequence instead
of handcoding it here.
o Remove GDB kluges to make this driver work with the pre-KDB remote
GDB code.
o Call kdb_enter() instead of Debugger().
Note that with this commit the dcons(4) driver cannot be used for
remote debugging anymore. This driver has to use the new GDB debug
port interface instead. Such has not been done yet.
a PCB from a trapframe for purposes of unwinding the stack. The PCB
is used as the thread context and all but the thread that entered the
debugger has a valid PCB.
This function can also be used to create a context for the threads
running on the CPUs that have been stopped when the debugger got
entered. This however is not done at the time of this commit.
in particular not without removing the options they replace or in the
proper location in this file. The purpose of this commit is to make it
possible to commit changes in parts without causing massive build
breakages. At least, that's the intend. I have no idea if it actually
works out as I hope...
in which multiple (presumably different) debugger backends can be
configured and which provides basic services to those backends.
Besides providing services to backends, it also serves as the single
point of contact for any and all code that wants to make use of the
debugger functions, such as entering the debugger or handling of the
alternate break sequence. For this purpose, the frontend has been
made non-optional.
All debugger requests are forwarded or handed over to the current
backend, if applicable. Selection of the current backend is done by
the debug.kdb.current sysctl. A list of configured backends can be
obtained with the debug.kdb.available sysctl. One can enter the
debugger by writing to the debug.kdb.enter sysctl.
backend improves over the old GDB support in the following ways:
o Unified implementation with minimal MD code.
o A simple interface for devices to register themselves as debug
ports, ala consoles.
o Compression by using run-length encoding.
o Implements GDB threading support.
Add copyiniov() which copies a struct iovec array in from userland into
a malloc'ed struct iovec. Caller frees.
Change uiofromiov() to malloc the uio (caller frees) and name it
copyinuio() which is more appropriate.
Add cloneuio() which returns a malloc'ed copy. Caller frees.
Use them throughout.
assigning a pointer to the list and then dereferencing the pointer as a
second step. When the first spin lock is acquired, curthread is not in
a critical section so it may be preempted and would end up using another
CPUs lock list instead of its own.
When this code was in witness_lock() this sequence was safe as curthread
was in a critical section already since witness_lock() is called after the
lock is acquired.
Tested by: Daniel Lang dl at leo.org
In this mode you can setup even very small stripe size and you can be
sure that only one I/O request will be send to every disks in stripe.
It consumes some more memory, but if allocation fails, it will fall
back to "ECONOMIC" mode.
It is about 10 times faster for small stripe size than "ECONOMIC" mode
and other RAID0 implementations. It is even recommended to use this
mode and small stripe size, so our requests are always splitted.
One can still use "ECONOMIC" mode by setting kern.geom.stripe.fast to 0.
It is also possible to setup maximum memory which "FAST" mode can consume,
by setting kern.geom.stripe.maxmem from /boot/loader.conf.
one go before returning. This avoids calling uiomove() while holding
allproc_lock.
Don't adjust uio->uio_offset manually, uiomove() does that for us.
Don't drop allproc_lock before calling panic().
Suggested by: alfred
so setfault would return correctly when a page fault was invalid
(e.g. a syscall with a bad parameter).
This caused an endless DSI loop, seen when running sendmail which
does a setlogin() call with a NULL pointer.
- introduce KTR_SYSC tracing. expose the syscallnames[] array to
make the tracing more readable.
- Avoid an additional lock acquire/release when leaving xl_intr(), by
changing xl_start*() to xl_start*_locked(), and calling the appropriate
routine by chip revision (as the DMA descriptors are different).
- Simplify the appropriate routines now that they are called with the
lock held.
This should save a significant amount of CPU cycles spent on servicing
each interrupt for both UP and SMP whilst remaining MPSAFE.
Tested by: rwatson
- Add *_locked() entry points as needed to avoid unnecessary lock thrashing.
- Use these entry points wisely.
- Only acquire the lock once when servicing an interrupt.
- Check 'suspended' on interrupt to avoid racing detach.
- Correct a mis-spelled comment.
- Don't take the lock in vr_reset() to avoid lock thrashing in attach.
- Comment this.
Reviewed by: -net (silence)
- Avoid unnecessary re-acquisition elsewhere by adding *_locked()
entry points as needed.
- Correct locking for the DEVICE_POLLING case.
- Hold the driver lock for the entire duration of interrupt servicing,
to avoid unneeded, expensive re-acquisition; use *_locked() entry
points as needed.
Reviewed by: -net (silence)
bootp -> BOOTP
bootp.nfsroot -> BOOTP_NFSROOT
bootp.nfsv3 -> BOOTP_NFSV3
bootp.compat -> BOOTP_COMPAT
bootp.wired_to -> BOOTP_WIRED_TO
- i.e. back out the previous commit. It's already possible to
pxeboot(8) with a GENERIC kernel.
Pointed out by: dwmalone
takes an argument to specify if it should preempt or not. Don't preempt
when sched_add_internal() is called from kseq_idled() or kseq_assign()
as in those cases we are about to call mi_switch() anyways. Also, doing
so during the first context switch on an AP leads to a NULL pointer deref
because curthread is NULL.
- Reenable preemption for ULE.
Submitted by: Taku YAMAMOTO taku at tackymt.homeip.net
