The working copy of leapfile resides in /var/dbntpd.leap-seconds.list.
/etc/ntp/leap-seconds (periodically updated from ftp://time.nist.gov/pub/
or ftp://tycho.usno.navy.mil/pub/ntp/) contains the master copy should
automatic leapfile updates be disabled (default).
Automatic leapfile updates are fetched from $ntp_leapfile_sources,
defaulting to https://www.ietf.org/timezones/data/leap-seconds.list,
within $ntp_leapfile_expiry_days (default 30 days) from leap-seconds
file expiry. Automatic updates can be enabled by setting
$daily_ntpd_leapfile_enable="YES" in periodic.conf. To avoid congesting
the ntp leapfile source the automatic update randomized by default but
can be disabled through daily_ntpd_avoid_congestion="NO" in
periodic.conf.
Suggested by: des
Reviewed by: des, roberto, dwmalone, ian, cperciva, glebius, gjb
MFC after: 1 week
X-MFC with: r289421, r293037
any root mount holds. The previous one used a wrong conditional - the
"err=$?" assignment resets "$?" to 0.
Submitted by: jilles@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
contain characters not allowed in a shell variable (such as "-").
These will be replaced by an underscore in jail config variables,
e.g. for jail "foo-bar" you would set "jail_foo_bar_hostname".
This is separate from the current code that changes the jail names
if they contain "." or "/". It also doesn't apply to jails defined
in a jail.conf file.
PR: 191181
MFC after: 5 days
USB NICs.
USB network hardware may not be enumerated and available when the rc.d
networking scripts run. Eventually the USB attachment completes and devd
events cause the network initialization to happen, but by then other rc.d
scripts have already failed, because services which depend on NETWORKING
(such as mountcritremote) may end up running before the network is actually
ready.
There is an existing netwait script, but because it is dependent on
NETWORKING it runs too late to prevent failure of some other rc
scripts. This change flips the order so that NETWORKING depends on netwait,
and netwait now depends on devd and routing (the former is needed to make
interfaces appear, and the latter is needed to run the ping tests in
netwait).
The netwait script used to be oriented primarily towards "as soon as any
host is reachable the network is fully functional", so you gave it a list of
IPs to try and you could optionally name an interface and it would wait for
carrier on that interface. That functionality still works the same, but now
you can provide a list of interfaces to wait for and it waits until each one
of them is available. The ping logic still completes as soon as the first IP
on the list responds.
These changes were submitted by Brenden Molloy <brendan+freebsd@bbqsrc.net>
in PR 205186, and lightly modified by me to allow a list of interfaces
instead of just one.
PR: 205186
Differential Revision: https://reviews.freebsd.org/D4608 (timeout w/o review)
to the rc scripts. With these changes, setting nfs_server_managegids="YES"
in /etc/rc.conf will enable this capability.
Suggested by: jpaetzel
Tested by: jpaetzel
Reviewed by: rc (pending)
MFC after: 2 weeks
This fixes /var/empty not being schg in the installation.
This was a change from fmtree to nmtree, that -i is now required to
apply these flags.
PR: 194189
Submitted by: guyyur@gmail.com
MFC after: 2 weeks
Relnotes: yes
if they are not required for mounting rootfs. However, it's possible
that some setups try to mount them in mountcritlocal (ie from fstab).
Export the list of current root mount holds using a new sysctl,
vfs.root_mount_hold, and make mountcritlocal retry if "mount -a" fails
and the list is not empty.
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3709
the module is built-in to the kernel then the kldunload will fail. Rather
than do this just check if there are rules and then remove them all.
Add requirement on FILESYSTEMS to ensure /usr is present for /usr/sbin/ugidfw
and /usr/bin/xargs. This was already effectively the ordering from rcorder(8).
MFC after: 2 weeks
Relnotes: yes
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
setups that worked before, flip the default to "YES". Most people don't
have /etc/rctl.conf, so they won't be affected in any way.
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
This is being done to fix breakage with make distribution with read-only
source trees as make distribution doesn't use make obj like building
tests/ does in all cases
Reported by: Wolfgang Zenker <wolfgang@lyxys.ka.sub.org>
Suggested by: jhb
X-MFC with: r282059
MFC after: 1 week
