this driver no longer needs to maintain an array of configured units.
Pass "softc" pointers instead of unit numbers to many functions that
did a conversion for unit->softc anyway.
Add the same type of safeguards we use in the mesg_in phase to the mesg_out
phase.
aic7xxx_reg.h:
Add definitions for the DSCommand register for PCI adapters.
whether of not to automatically #define EXCLUDE_AUDIO; MSS is a real
audio device and we should not #define EXCLUDE_AUDIO if we have one.
(And I want it because it's the only mixer-capable audio driver that I
can use with my crummy Packard Bell (nee Aztech) audio board.)
This fixes the very confusing condition where having all of this:
mss0 at 0x530 irq 10 drq 1 on isa
gus0: <MS Sound System (CS4231)>
opl0 at 0x388 on isa
opl0: <Yamaha OPL-3 FM>
mpu0 at 0x300 irq 9 drq 0 on isa
mpu0: <MPU-401 MIDI Interface 0.0 >
will still give you this:
% cat /dev/sndstat
SoundCard Error: The soundcard system has not been configured
Also remove an unnecessary newline in the printf() message for the
'gus0' device shown above so that we don't wind up printing a blank
line between mss0 and gus0.
was overlapping with another file, and making some undesirable behavior a
little worse - it's triggering a bug in config that appears to have been
there for some time (before the options files, anyway.)
On some laptops, this doesn't work (ie; IBM 75x series), so force it
to power on.
With this modification, I am able to read the tuples off 4 different
PCMCIA cards on my ThinkPad.
Reviewed by: phk@FreeBSD.org
Obtained from: if_zp.c
the range [210:260] by sweeping the problem under the rug. This change
has the following effects:
1) A new MIB variable in the kern branch is defined to allow modification
of the socket buffer layer's ``wastage factor'' (which determines how
much unused-but-allocated space in mbufs and mbuf clusters is allowed
in a socket buffer).
2) The default value of the wastage factor is changed from 2 to 8.
The original value was chosen when MINCLSIZE was 7*MLEN (!), and is not
appropriate for an environment where MINCLSIZE is much less.
The real solution to this problem is to scrap both mbufs and sockbufs
and completely redesign the buffering mechanism used at both levels.
to enable IP forwarding, use sysctl(8). Also did the same for IPX,
which involved inventing a completely new MIB from whole cloth (which
I may not quite have correct); be aware of this if you use IPX forwarding.
(The two should never have been controlled by the same option anyway.)
consider "safe" for most systems. Note that this is (has been for some
time) also tunable with sysctl (via kern.somaxconn) should the operator
wish to increase this value even higher. Also note that 128 is what
the Netscape WWW server reportedly asks for.
Simplify the initialization of adapters by pulling all card specific
initialization to the card specific modules.
Set the Latency timer and Burst len to good values if thery are not
initialized during post or are reset during chip reset.
Properly identify and handle external SCB SRAM. The code was false
id'ing 255 SCBs on aic7880 chips.
Reviewed by: David Greenman <davidg@FreeBSd.org>
Simplify the initialization of adapters by pulling all card specific
initialization to the card specific modules.
Update comments and fix formating.
Pass struct ahc_data*'s to functions instead of unit numbers.
Take advantage of the quad word alignment of SCB fields.
Adapt to new sequencer changes:
1) Waiting scb list no longer has a tail.
2) Fill the message buffer as appropriate during a parity error.
3) Count all of the SGs involved in a residual instead of just
the current one.
The reset/abort code still needs a lot of work.
Reviewed by: David Greenman <davidg@FreeBSd.org>
aic7770.c:
Simplify the initialization of adapters by pulling all card specific
initialization to the card specific modules.
eisaconf.c:
outb 0x80 instead of 0xc80. The top byte is truncated anyway, and 0x80
was what was intended.
1) Use cpp to preprocess the sequencer code.
2) Convert all "magic numbers" to #defines shared by the sequencer and
kernel driver via the aic7xxx_reg.h file. (The assembler still needs
to be re-written in lex/yacc to allow ~|& type constructions).
3) Raise ATN on parity errors for "in" phases and send an initiator detected
error or message-in parity error message as appropriate.
4) Turn off the reselection hardware from the time or a (re)connection to
busfree. It seems that some fast targets were able to reconnect before
the sequencer was able to see busfree.
5) The message buffer is considered "in-use" when there is a positive length
count. The ACTIVE_MSG flag was unnecesary.
6) Properly set SCB_NEXT_WAITING to SCB_LIST_HEAD in scbs being added to
the waiting scb list. This is a change in how the list code works to
facilitate some planned work in the reset code.
7) The fields in the SCB have be re-arranged to be quad-word aligned.
8) The inb code has been rewritten to catch phasemisses and be more efficient.
9) Go back to "snooping the bus" to determine if the incomming identify
message will be followed by a simple queue message. Its much faster than
doing a search through the SCBs.
10) Implement better tag range checking for incomming tags.
11) Make sdtr_to_rate more accurate (use 25 instead of 24 in calculations -
must have been asleep that night).
12) Rearrange some routines to reduce code complexity and size.
13) Update comments and formatting.
14) Fixed bugs I've forgotten about??
Reviewed by: David Greenman <davidg@FreeBSD.org>
enough nodes for the number of ports on the last module, not the number
of ports _total_ that the driver is managing...
Submitted by: Robert Sanders <rsanders@mindspring.com>
were development aids :-) and normal events.
Initialise the "hidden" blueprint mount "mnt_op" and "mnt_vfc" fields so
that a statfs() on a devfs file would not panic anymore. Fixes PR#911.
Head-scratching by: Julian and Peter
