check hash to the filesystem inodes. Access attempts to files
associated with an inode with an invalid check hash will fail with
EINVAL (Invalid argument). Access is reestablished after an fsck
is run to find and validate the inodes with invalid check-hashes.
This check avoids a class of filesystem panics related to corrupted
inodes. The hash is done using crc32c.
Note this check-hash is for the inode itself and not any of its
indirect blocks. Check-hash validation may be extended to also
cover indirect block pointers, but that will be a separate (and
more costly) feature.
Check hashes are added only to UFS2 and not to UFS1 as UFS1 is
primarily used in embedded systems with small memories and low-powered
processors which need as light-weight a filesystem as possible.
Reviewed by: kib
Tested by: Peter Holm
Sponsored by: Netflix
superblock has a check-hash error, an error message noting the
superblock check-hash failure is printed and the mount fails. The
administrator then runs fsck to repair the filesystem and when
successful, the filesystem can once again be mounted.
This approach fails if the filesystem in question is a root filesystem
from which you are trying to boot. Here, the loader fails when trying
to access the filesystem to get the kernel to boot. So it is necessary
to allow the loader to ignore the superblock check-hash error and make
a best effort to read the kernel. The filesystem may be suffiently
corrupted that the read attempt fails, but there is no harm in trying
since the loader makes no attempt to write to the filesystem.
Once the kernel is loaded and starts to run, it attempts to mount its
root filesystem. Once again, failure means that it breaks to its prompt
to ask where to get its root filesystem. Unless you have an alternate
root filesystem, you are stuck.
Since the root filesystem is initially mounted read-only, it is
safe to make an attempt to mount the root filesystem with the failed
superblock check-hash. Thus, when asked to mount a root filesystem
with a failed superblock check-hash, the kernel prints a warning
message that the root filesystem superblock check-hash needs repair,
but notes that it is ignoring the error and proceeding. It does
mark the filesystem as needing an fsck which prevents it from being
enabled for writing until fsck has been run on it. The net effect
is that the reboot fails to single user, but at least at that point
the administrator has the tools at hand to fix the problem.
Reported by: Rick Macklem (rmacklem@)
Discussed with: Warner Losh (imp@)
Sponsored by: Netflix
document the libufs interface for fetching and storing inodes.
The undocumented getino / putino interface has been replaced
with a new getinode / putinode interface.
Convert the utilities that had been using the undocumented
interface to use the new documented interface.
No functional change (as for now the libufs library does not
do inode check-hashes).
Reviewed by: kib
Tested by: Peter Holm
Sponsored by: Netflix
to a read-write descriptor. Do not close the read-only descriptor until
the read-write is successfully obtained. Before this fix, a failed upgrade
left no usable descriptor with which to work.
Followup to r313780. Also prefix ext2's and nandfs's versions with
EXT2_ and NANDFS_.
Reported by: kib
Reviewed by: kib, mckusick
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D9623
to fix the memory leak that I introduced in r328426. Instead of
trying to clear up the possible memory leak in all the clients, I
ensure that it gets cleaned up in the source (e.g., ffs_sbget ensures
that memory is always freed if it returns an error).
The original change in r328426 was a bit sparse in its description.
So I am expanding on its description here (thanks cem@ and rgrimes@
for your encouragement for my longer commit messages).
In preparation for adding check hashing to superblocks, r328426 is
a refactoring of the code to get the reading/writing of the superblock
into one place. Unlike the cylinder group reading/writing which
ends up in two places (ffs_getcg/ffs_geom_strategy in the kernel
and cgget/cgput in libufs), I have the core superblock functions
just in the kernel (ffs_sbfetch/ffs_sbput in ffs_subr.c which is
already imported into utilities like fsck_ffs as well as libufs to
implement sbget/sbput). The ffs_sbfetch and ffs_sbput functions
take a function pointer to do the actual I/O for which there are
four variants:
ffs_use_bread / ffs_use_bwrite for the in-kernel filesystem
g_use_g_read_data / g_use_g_write_data for kernel geom clients
ufs_use_sa_read for the standalone code (stand/libsa/ufs.c
but not stand/libsa/ufsread.c which is size constrained)
use_pread / use_pwrite for libufs
Uses of these interfaces are in the UFS filesystem, geoms journal &
label, libsa changes, and libufs. They also permeate out into the
filesystem utilities fsck_ffs, newfs, growfs, clri, dump, quotacheck,
fsirand, fstyp, and quot. Some of these utilities should probably be
converted to directly use libufs (like dumpfs was for example), but
there does not seem to be much win in doing so.
Tested by: Peter Holm (pho@)
ffs_sbget() may return a superblock buffer even if it fails, so the
caller must be prepared to free it in this case. Moreover, when tasting
alternate superblock locations in a loop, ffs_sbget()'s readfunc
callback must free the previously allocated buffer.
Reported and tested by: pho
Reviewed by: kib (previous version)
Differential Revision: https://reviews.freebsd.org/D14390
Specifically reading is done if ffs_sbget() and writing is done
in ffs_sbput(). These functions are exported to libufs via the
sbget() and sbput() functions which then used in the various
filesystem utilities. This work is in preparation for adding
subperblock check hashes.
No functional change intended.
Reviewed by: kib
check-hash after making changes to the cylinder group. The problem
was that the journal-recovery code was calling the libufs bwrite()
function instead of the cgput() function. The cgput() function updates
the cylinder-group check-hash before writing the cylinder group.
This change required the additions of the cgget() and cgput() functions
to the libufs API to avoid a gratuitous bcopy of every cylinder group
to be read or written. These new functions have been added to the
libufs manual pages. This was the first opportunity that I have had
to use and document the use of the EDOOFUS error code.
Reviewed by: kib
Reported by: emaste and others
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using mis-identified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
check hash to cylinder groups. If a check hash fails when a cylinder
group is read, no further allocations are attempted in that cylinder
group until it has been fixed by fsck. This avoids a class of
filesystem panics related to corrupted cylinder group maps. The
hash is done using crc32c.
Check hases are added only to UFS2 and not to UFS1 as UFS1 is primarily
used in embedded systems with small memories and low-powered processors
which need as light-weight a filesystem as possible.
Specifics of the changes:
sys/sys/buf.h:
Add BX_FSPRIV to reserve a set of eight b_xflags that may be used
by individual filesystems for their own purpose. Their specific
definitions are found in the header files for each filesystem
that uses them. Also add fields to struct buf as noted below.
sys/kern/vfs_bio.c:
It is only necessary to compute a check hash for a cylinder
group when it is actually read from disk. When calling bread,
you do not know whether the buffer was found in the cache or
read. So a new flag (GB_CKHASH) and a pointer to a function to
perform the hash has been added to breadn_flags to say that the
function should be called to calculate a hash if the data has
been read. The check hash is placed in b_ckhash and the B_CKHASH
flag is set to indicate that a read was done and a check hash
calculated. Though a rather elaborate mechanism, it should
also work for check hashing other metadata in the future. A
kernel internal API change was to change breada into a static
fucntion and add flags and a function pointer to a check-hash
function.
sys/ufs/ffs/fs.h:
Add flags for types of check hashes; stored in a new word in the
superblock. Define corresponding BX_ flags for the different types
of check hashes. Add a check hash word in the cylinder group.
sys/ufs/ffs/ffs_alloc.c:
In ffs_getcg do the dance with breadn_flags to get a check hash and
if one is provided, check it.
sys/ufs/ffs/ffs_vfsops.c:
Copy across the BX_FFSTYPES flags in background writes.
Update the check hash when writing out buffers that need them.
sys/ufs/ffs/ffs_snapshot.c:
Recompute check hash when updating snapshot cylinder groups.
sys/libkern/crc32.c:
lib/libufs/Makefile:
lib/libufs/libufs.h:
lib/libufs/cgroup.c:
Include libkern/crc32.c in libufs and use it to compute check
hashes when updating cylinder groups.
Four utilities are affected:
sbin/newfs/mkfs.c:
Add the check hashes when building the cylinder groups.
sbin/fsck_ffs/fsck.h:
sbin/fsck_ffs/fsutil.c:
Verify and update check hashes when checking and writing cylinder groups.
sbin/fsck_ffs/pass5.c:
Offer to add check hashes to existing filesystems.
Precompute check hashes when rebuilding cylinder group
(although this will be done when it is written in fsutil.c
it is necessary to do it early before comparing with the old
cylinder group)
sbin/dumpfs/dumpfs.c
Print out the new check hash flag(s)
sbin/fsdb/Makefile:
Needs to add libufs now used by pass5.c imported from fsck_ffs.
Reviewed by: kib
Tested by: Peter Holm (pho)
Extend the ino_t, dev_t, nlink_t types to 64-bit ints. Modify
struct dirent layout to add d_off, increase the size of d_fileno
to 64-bits, increase the size of d_namlen to 16-bits, and change
the required alignment. Increase struct statfs f_mntfromname[] and
f_mntonname[] array length MNAMELEN to 1024.
ABI breakage is mitigated by providing compatibility using versioned
symbols, ingenious use of the existing padding in structures, and
by employing other tricks. Unfortunately, not everything can be
fixed, especially outside the base system. For instance, third-party
APIs which pass struct stat around are broken in backward and
forward incompatible ways.
Kinfo sysctl MIBs ABI is changed in backward-compatible way, but
there is no general mechanism to handle other sysctl MIBS which
return structures where the layout has changed. It was considered
that the breakage is either in the management interfaces, where we
usually allow ABI slip, or is not important.
Struct xvnode changed layout, no compat shims are provided.
For struct xtty, dev_t tty device member was reduced to uint32_t.
It was decided that keeping ABI compat in this case is more useful
than reporting 64-bit dev_t, for the sake of pstat.
Update note: strictly follow the instructions in UPDATING. Build
and install the new kernel with COMPAT_FREEBSD11 option enabled,
then reboot, and only then install new world.
Credits: The 64-bit inode project, also known as ino64, started life
many years ago as a project by Gleb Kurtsou (gleb). Kirk McKusick
(mckusick) then picked up and updated the patch, and acted as a
flag-waver. Feedback, suggestions, and discussions were carried
by Ed Maste (emaste), John Baldwin (jhb), Jilles Tjoelker (jilles),
and Rick Macklem (rmacklem). Kris Moore (kris) performed an initial
ports investigation followed by an exp-run by Antoine Brodin (antoine).
Essential and all-embracing testing was done by Peter Holm (pho).
The heavy lifting of coordinating all these efforts and bringing the
project to completion were done by Konstantin Belousov (kib).
Sponsored by: The FreeBSD Foundation (emaste, kib)
Differential revision: https://reviews.freebsd.org/D10439
This both avoids some dependencies on xinstall.host and allows
bootstrapping on older releases to work due to lack of at least 'install -l'
support.
Sponsored by: EMC / Isilon Storage Division
Since METAMODE has been added, sys.mk loads bsd.mkopt.mk which ends load loading
bsd.own.mk which then defines SHLIBDIR before all the Makefile.inc everywhere.
This makes /lib being populated again.
Reported by: many
Off by default, build behaves normally.
WITH_META_MODE we get auto objdir creation, the ability to
start build from anywhere in the tree.
Still need to add real targets under targets/ to build packages.
Differential Revision: D2796
Reviewed by: brooks imp
the construct like printf("%\s", NULL) resulting from macroexpand of
ERROR(u, NULL), making it impossible to use LIBUFS_DEBUGGING.
With inline function, compiler cannot detect the NULL argument to
known function and does not try to convert it into puts().
In collaboration with: pho
brings in support for an optional intent log which eliminates the need
for background fsck on unclean shutdown.
Sponsored by: iXsystems, Yahoo!, and Juniper.
With help from: McKusick and Peter Holm
Similar to libexec/, do the same with lib/. Make WARNS=6 the norm and
lower it when needed.
I'm setting WARNS?=0 for secure/. It seems secure/ includes the
Makefile.inc provided by lib/. I'm not going to touch that directory.
Most of the code there is contributed anyway.
use almost anything that uses libufs(3) against a file as an unprivileged user, e.g.
tunefs(8) and dumpfs(8) against a makefs(8)-created image.
Prodded by: kensmith
