Also, the previous commit to sys/dev/if_ndis/if_ndis.c also included the
removal of a call to ndis_setstate_80211 that is no longer needed.
Submitted by: sam
MFC after: 3 days
perform 802.11 operations directly on the ndis0 interface before the
first VAP (wlan0) had been created. This would lead to a NULL-pointer
dereference in the kernel.
Submitted by: Paul B. Mahol <onemda@gmail.com>
MFC after: 3 days
nagged again via PR. Thank Paul for his persistence and contributions.
PR: 136895
Submitted by: Paul B. Mahol <onemda@gmail.com>
Reviewed by: sam (timeout, 10 days), weongyo (timeout, 10 days), me
Approved by: re (Kostik Belousov <kostikbel@gmail.com>)
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
or URB_FUNCTION_CLASS_xxx with HAL preemption lock that means it's
non-sleepable during USB requests though usb2_do_request() requires a
sleep so it needs to send queries to the default pipe without those
interfaces to avoid sleep.
Based on the HAL preemption lock there is a problem on SMP machines
and causes a panic.
o When a device detached the current tactic to detach NDIS USB driver is
to call SURPRISE_REMOVED event. So it don't need to call
ndis_halt_nic() again. This fixes some page faults when some drivers
work abnormal.
o it assumes now that URB_FUNCTION_BULK_OR_INTERRUPT_TRANSFER is in
DISPATCH_LEVEL (non-sleepable) and as further work
URB_FUNCTION_VENDOR_XXX and URB_FUNCTION_CLASS_XXX should be.
Reviewed by: Hans Petter Selasky <hselasky_at_freebsd.org>
Tested by: Paul B. Mahol <onemda_at_gmail.com>
o correct dBm<->mW conversion logic
o set net80211 TXPMGT capability only if driver reports it is capable
PR: kern/132342
Submitted by: "Paul B. Mahol" <onemda@gmail.com>
o implement URB_FUNCTION_ABORT_PIPE handling.
o remove unused code related with canceling the timer list for USB
drivers.
o whitespace cleanup and style(9)
Obtained from: hps's original patch
Now the NDISulator supports NDIS USB drivers that it've tested with
devices as follows:
- Anygate XM-142 (Conexant)
- Netgear WG111v2 (Realtek)
- U-Khan UW-2054u (Marvell)
- Shuttle XPC Accessory PN20 (Realtek)
- ipTIME G054U2 (Ralink)
- UNiCORN WL-54G (ZyDAS)
- ZyXEL G-200v2 (ZyDAS)
All of them succeeded to attach and worked though there are still some
problems that it's expected to be solved.
To use NDIS USB support, you should rebuild and install ndiscvt(8) and
if you encounter a problem to attach please set `hw.ndisusb.halt' to
0 then retry.
I expect no changes of the NDIS code for PCI, PCMCIA devices.
Obtained from: //depot/projects/ndisusb/...
NDIS_TXPKTS and don't allocate unused extra spaces for sc->ndis_txarray
and sc->ndis_txpool.
PR: kern/127644
Submitted by: Antoine Pelisse <apelisse_at_gmail.com>
MFC after: 1 week
mutexes and replacing the obsolete if_watchdog interface. The ndis_ticktask
function calls into ieee80211_new_state under one condition with NDIS_LOCK
held. The ieee80211_new_state would call into ndis_start in some cases too,
resulting in the occasional case where ndis_start acquires NDIS_LOCK from
inside the NDIS_LOCK held by ndis_ticktask.
Obtained from: Paul B. Mahol <onemda@gmail.com>
MFC after: 1 week
mtx interface for NDIS_LOCK/UNLOCK. This should result in less
CPU utilization on behalf of the ndis driver. Additionally, this
commit also fixes a potential LOR in the ndis_tick code, by
not locking inside the ndis_tick function, but instead delegating
that work to the helpers called through IoQueueWorkItem. The
way that this is currently set up for NDIS prevents us from
simply implementing a callout_init_mtx mechanism.
However, the helper functions that handle the various timeout
cases implement fine-grained locking using the spinlocks provided
by the NDIS-compat layer, and using the mtx that is added with
this commit. This leaves the following ndis_softc members operated
on in ndis_tick in an unlocked context:
* ndis_hang_timer - Only modified outside of ndis_tick once, before
the first callout_reset to schedule ndis_tick
* ifp->if_oerrors - Only incremented in two places, which should be
an atomic op
* ndis_tx_timer - Assigned to 5 (when guaranteed to be 0) or 0
(in txeof), to indicate to ndis_tick what to
do. This is the only member of which I was
suspicious for needing the NDIS_LOCK here. My
testing (and another's) have been fine so far.
* ndis_stat_callout - Only uses a simple set of callout routines,
callout_reset only called by ndis_tick after
the initial reset, and then callout_drain is
used exactly once in shutdown code.
The benefit is that ndis_tick doesn't acquire NDIS_LOCK unless one of
the timeout conditions is flagged, and it still obeys the locking
order semantics that are dictated by the NDIS layer at the moment. I
have been investigating a more thorough s/spinlock/mtx/ of the NDIS
layer, but the simplest naive approach (replace KeAcquireSpinLock
with an mtx implementation) has anti-succeeded for me so far. This
is a good first step though.
Tested by: onemda@gmail.com
Reviewed by: current@, jhb, thompsa
Proposed by: jhb
bring it more up to date. The watchdog timer, and its
associated code, is all collapsed into the ndis_tick function
that was implemented for the NDIS-subsystem watchdog. This
implementation is similar to what numerous other drivers use
to implement the watchdog.
Reviewed by: thompsa, jhb
MFC after: 2 weeks
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
- Limit grabbing the lock to SIOCSIFFLAGS.
- Move ieee80211_start_all() to SIOCSIFFLAGS.
- Remove SIOCSIFMEDIA as it is not useful.
- Limit ether_ioctl to only SIOCGIFADDR. SIOCSIFADDR and SIOCSIFMTU have no
affect as there is no input/output path in the vap parent. The vap code
will handle the reinit of the mac address changes.
- Split off ndis_ioctl_80211 as it was getting too different to wired devices.
This fixes a copyout while locked and a lock recursion.
Reviewed by: sam
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
as the former is becoming deprecated and exhibits some extraneous
Giant-locking. The new callout(9) is declared MPSAFE, so it may
improve concurrency.
Tested by: matteo
Silence from: wpaul
MFC after: 1 month
pass back the desired buffer length. This fixes scanning with the Marvell
88W8335 and BCM4328 wireless cards.
PR: kern/118370
Submitted by: Weongyo Jeong
Tested by: Ed Schouten
