via sysctl(4) interface. This permits router not to stop forwarding
packets while route table is being written to user-supplied buffer.
Reported by: Pawel Tyll <ptyll@nitronet.pl>
Approved by: kib(mentor)
MFC after: 1 week
as otherwise the interrupt handling code may modify data in the non-DMA
part of the cache line while we have it stashed away in the temporary
stack buffer, then we end up restoring a stale value.
PR: 160431
Submitted by: Ian Lepore
MFC after: 1 week
cover the initial stack size. For MCL_WIREFUTURE maps, the subsequent
call to vm_map_wire() to wire the whole stack region fails due to
VM_MAP_WIRE_NOHOLES flag.
Use the VM_MAP_WIRE_HOLESOK to only wire mapped part of the stack.
Reported and tested by: Sushanth Rai <sushanth_rai yahoo com>
Reviewed by: alc
MFC after: 1 week
sys/dev/dpt/dpt_scsi.c:612:18: error: implicit truncation from 'int' to bitfield changes value from -2 to 2 [-Werror,-Wconstant-conversion]
dpt->cache_type = DPT_CACHE_WRITEBACK;
^ ~~~~~~~~~~~~~~~~~~~
by defining DPT_CACHE_WRITEBACK as 2, since dpt_softc::cache_type is an
unsigned bitfield. No binary change.
MFC after: 1 week
The default priority is now '1000' rather than '0'. This may cause some
unforseen regressions.
Submitted by: Stefan Bethke <stb@lassitu.de>
Reviewed by: imp
- When switching to 4-bit operation, send a SET_CLR_CARD_DETECT command
to disconnect the card-detect pull-up resistor from the DAT3 line before
sending the SET_BUS_WIDTH command.
- Add the missing "reserved" zero entry to the mantissa table used to
decode various CSD fields. This was causing SD cards to report that they
could run at 30 MHz instead of the maximum 25 MHz mandated in the spec.
o Enhancements:
- At the MMC layer, format various info from the CID into a string that
uniquely identifies the card instance (manufacturer number, serial
number, product name and revision, etc). Export it as an instance
variable.
- At the MMCSD layer, display the formatted card ID string, and also
report the clock speed of the hardware (not the card's max speed), and
the number of bits and number of blocks per transfer. It comes out like
this now:
mmcsd0: 968MB <SD SD01G 8.0 SN 276886905 MFG 08/2008 by 3 SD> at mmc0
22.5MHz/4bit/128-block
o Use DEVMETHOD_END.
o Use NULL instead of 0 for pointers.
PR: 156496
Submitted by: Ian Lepore
MFC after: 1 week
sys/contrib/rdma/rdma_cma.c:1259:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ECONNRESET:
^
@/sys/errno.h:118:20: note: expanded from macro 'ECONNRESET'
#define ECONNRESET 54 /* Connection reset by peer */
^
sys/contrib/rdma/rdma_cma.c:1263:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ETIMEDOUT:
^
@/sys/errno.h:124:19: note: expanded from macro 'ETIMEDOUT'
#define ETIMEDOUT 60 /* Operation timed out */
^
sys/contrib/rdma/rdma_cma.c:1260:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ECONNREFUSED:
^
@/sys/errno.h:125:22: note: expanded from macro 'ECONNREFUSED'
#define ECONNREFUSED 61 /* Connection refused */
^
This is because the switch uses iw_cm_event::status, which is an enum
iw_cm_event_status, while ECONNRESET, ETIMEDOUT and ECONNREFUSED are
just plain defines from errno.h.
It looks like there is only one use of any of the enumeration values of
iw_cm_event_status, in:
sys/contrib/rdma/rdma_iwcm.c: if (iw_event->status == IW_CM_EVENT_STATUS_ACCEPTED) {
So messing around with the enum definitions to fix the warning seems too
disruptive; the simplest fix is to cast the argument of the switch to
int.
Reviewed by: kmacy
MFC after: 1 week
sys/dev/nxge/if_nxge.c:1276:11: error: case value not in enumerated type 'xge_hal_event_e' (aka 'enum xge_hal_event_e') [-Werror,-Wswitch]
case XGE_LL_EVENT_TRY_XMIT_AGAIN:
^
sys/dev/nxge/if_nxge.c:1289:11: error: case value not in enumerated type 'xge_hal_event_e' (aka 'enum xge_hal_event_e') [-Werror,-Wswitch]
case XGE_LL_EVENT_DEVICE_RESETTING:
^
This is because the switch uses xge_queue_item_t::event_type, which is
an enum xge_hal_event_e, while the XGE_LL_EVENT_xx values are of the
enum xge_event_e.
Since messing around with the enum definitions is too disruptive, the
simplest fix is to cast the argument of the switch to int.
Reviewed by: gnn
MFC after: 1 week
STAILQ(). While here, fix another clang warning about a switch which
tests an enum type for a regular integer value.
Submitted by: jhb
MFC after: 1 week
assumes for small buffers (< 64k) that the OS driver is actually using
a buffer rounded up to the next power of 2. It also assumes that the
buffer is at least 4k in size. Furthermore, there is at least one
known instance of megarc sending a request with a 12k buffer where the
firmware writes out a 24k-ish reply.
To workaround the data corruption triggered by this "feature", ensure
that buffers for user commands use a minimum size of 32k, and that
buffers between 32k and 64k use a 64k buffer.
PR: kern/155658
Submitted by: Andreas Longwitz longwitz incore de
Reviewed by: scottl
MFC after: 1 week
code that is used to construct a loader (e.g. libstand, ficl, etc).
There is such a thing as a 64-bit EFI application, but it's not
as standard as 32-bit is. Let's make the 32-bit functional (as in
we can load and actualy boot a kernel) before solving the 64-bit
loader problem.
ar724x_pci.c.
* Move out the code which populates the firmware into ar71xx_fixup.c
* Shuffle around the ar724x fixup code to match what the ar71xx fixup
code does.
I've validated this on an AR7240 with AR9285 on-board NIC. It doesn't
yet load, as the AR9285 EEPROM code needs to be made "flash aware."
TODO:
* Validate that I haven't broken AR71xx
* Test AR9285/AR9287 onboard NICs, complete with EEPROM code changes
* Port over the needed BAR hacks for AR7240, AR7241 and AR7242 from
Linux OpenWRT. The current WAR has only been tested on the AR7240
and I'm not sure the way the BAR register is treated is "right".
The "fixup" method here is right when setting the BAR for local access -
ie, the BAR address is either 0xffff (AR7240) or 0x1000ffff (AR7241/AR7242),
but the ath9k-fixup.c code (Linux OpenWRT) does this when setting the
initial "fixup" BAR. It then restores the original BAR.
I'll have to read the ar724x PCI bus glue to see what other special cases
await.
over just the active vnodes associated with a mount point to replace
MNT_VNODE_FOREACH_ALL in the vfs_msync, ffs_sync_lazy, and qsync
routines.
The vfs_msync routine is run every 30 seconds for every writably
mounted filesystem. It ensures that any files mmap'ed from the
filesystem with modified pages have those pages queued to be
written back to the file from which they are mapped.
The ffs_lazy_sync and qsync routines are run every 30 seconds for
every writably mounted UFS/FFS filesystem. The ffs_lazy_sync routine
ensures that any files that have been accessed in the previous
30 seconds have had their access times queued for updating in the
filesystem. The qsync routine ensures that any files with modified
quotas have those quotas queued to be written back to their
associated quota file.
In a system configured with 250,000 vnodes, less than 1000 are
typically active at any point in time. Prior to this change all
250,000 vnodes would be locked and inspected twice every minute
by the syncer. For UFS/FFS filesystems they would be locked and
inspected six times every minute (twice by each of these three
routines since each of these routines does its own pass over the
vnodes associated with a mount point). With this change the syncer
now locks and inspects only the tiny set of vnodes that are active.
Reviewed by: kib
Tested by: Peter Holm
MFC after: 2 weeks
a mount point. Active vnodes are those with a non-zero use or hold
count, e.g., those vnodes that are not on the free list. Note that
this list is in addition to the list of all the vnodes associated
with a mount point.
To avoid adding another set of linkage pointers to the vnode
structure, the active list uses the existing linkage pointers
used by the free list (previously named v_freelist, now renamed
v_actfreelist).
This update adds the MNT_VNODE_FOREACH_ACTIVE interface that loops
over just the active vnodes associated with a mount point (typically
less than 1% of the vnodes associated with the mount point).
Reviewed by: kib
Tested by: Peter Holm
MFC after: 2 weeks
actually in it. This happens when SCTP receives an unknown chunk, which
requires the sending of an ERROR chunk, and there is no final padding but
the chunk is not 4-byte aligned.
Reported by yueting via rwatson@
MFC after: 3 days
at least until I can root cause what's going on.
The only platform I've seen this on is the AR9220 when attached to
the AR71xx CPUs. I get immediate PCIe bus errors and all subsequent
accesses cause further MIPS bus exceptions. I don't have any other
big-endian platforms to test this on.
If I get a chance (or two), I'll try to whack this on a bus analyser
and see exactly what happens.
I'd rather leave this on, especially for slower, embedded platforms.
But the #ifdef hell is something I'm trying to avoid.
- Implement "configure" command to allow switching operation mode of
running device on-fly without destroying and recreation.
- Implement Active/Read mode as hybrid of Active/Active and Active/Passive.
In this mode all paths not marked FAIL may handle reads same time,
but unlike Active/Active only one path handles write requests at any
point in time. It allows to closer follow original write request order
if above layers need it for data consistency (not waiting for requisite
write completion before sending dependent write).
- Hide duplicate messages about device status change.
- Remove periodic thread wake up with 10Hz rate.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
used only as a helper function in that file. Replace sole call to
vbusy() with inline code in vholdl(). Replace sole calls to vfree()
and vdestroy() with inline code in vdropl().
The Clang compiler already inlines these functions, so they do not
show up in a kernel backtrace which is confusing. Also you cannot
set their frame in kgdb which means that it is impossible to view
their local variables. So, while the produced code is unchanged,
the debugging should be easier.
Discussed with: kib
MFC after: 2 weeks
The primary changes are that the user of the interface no longer
needs to manage the mount-mutex locking and that the vnode that
is returned has its mutex locked (thus avoiding the need to check
to see if its is DOOMED or other possible end of life senarios).
To minimize compatibility issues for third-party developers, the
old MNT_VNODE_FOREACH interface will remain available so that this
change can be MFC'ed to 9. Following the MFC to 9, MNT_VNODE_FOREACH
will be removed in head.
The reason for this update is to prepare for the addition of the
MNT_VNODE_FOREACH_ACTIVE interface that will loop over just the
active vnodes associated with a mount point (typically less than
1% of the vnodes associated with the mount point).
Reviewed by: kib
Tested by: Peter Holm
MFC after: 2 weeks
allow the owner to read and write ACL and file attributes when there
was no entry with subject matching the owner. In other words,
'getfacl meh' shouldn't fail for the owner if the ACL looks like this:
# file: meh
# owner: trasz
# group: wheel
user:root:------a-------:------:allow
Reported by: kientzle
like the one triggered by this:
# kldload geom_vinum
# pwait `pgrep -S gv_worker` &
# kldunload geom_vinum
or this:
GEOM_JOURNAL: Shutting down geom gjournal 3464572051.
panic: destroying non-empty racct: 1 allocated for resource 6
which were tracked by jh@ to be caused by checking p->p_flag,
while it wasn't initialised yet. Basically, during fork, the code
checked p_flag, concluded the process isn't marked as P_SYSTEM,
incremented the counter, and later on, when exiting, checked that
the process was marked as P_SYSTEM, and thus didn't decrement it.
Also, I believe there wasn't any good reason for checking P_SYSTEM
in the first place.
Tested by: jh
even in the face of errors.
If the RX descriptor list fails, the RX lock won't be initialised, but
then the DMA free path wil try freeing it.
This commit is brought to you by a working mwl(4).
but GNU libc used it without checking its kernel version, e. g., Fedora 10.
- Move pipe(2) implementation for Linuxulator from MD files to MI file,
sys/compat/linux/linux_file.c. There is no MD code for this syscall at all.
- Correct an argument type for pipe() from l_ulong * to l_int *. Probably
this was the source of MI/MD confusion.
Reviewed by: emulation
push the address onto stack as we do for INTn emulation. This avoids stack
underflow when we encounter RETF instruction in VM86 mode. Lack of this
exit point actually caused page fault in VM86 mode with VESA module when we
resume from suspend state[1].
- Remove unnecessary CLI and STI instructions from BIOS interrupt emulation.
INTn and IRET must be able to emulate the flag correctly.
Reported by: gavin [1]
Tested by: gavin (early revision)
MFC after: 3 days
last show-stopper keeping PREEMPTION from being usable on sparc64 should
have been dealt with in r230662.
At least on 2-way systems, PREEMPTION causes a little bit of a degradation
in worldstone performance. However, FreeBSD seems to have started building
up regressions in !PREEMPTION cases so sparc64 better should not be an
oddball in this regard.
MFC after: 1 week
Since r230208 update mounts were allowed if the list of mount options
contained the "export" option. This is not correct as tmpfs doesn't
really support updating all options.
Reviewed by: kevlo, trociny
proposed MTU value from it and update the TCP host cache. Then
tcp_mss_update() is called on the corresponding tcpcb. It finds the
just allocated entry in the TCP host cache and updates MSS on the
tcpcb. And then we do a fast retransmit of what we have in the tcp
send buffer.
This sequence gets broken if the TCP host cache is exausted. In this
case allocation fails, and later called tcp_mss_update() finds nothing
in cache. The fast retransmit is done with not reduced MSS and is
immidiately replied by remote host with new ICMP datagrams and the
cycle repeats. This ping-pong can go up to wirespeed.
To fix this:
- tcp_mss_update() gets new parameter - mtuoffer, that is like
offer, but needs to have min_protoh subtracted.
- tcp_mtudisc() as notification method renamed to tcp_mtudisc_notify().
- tcp_mtudisc() now accepts not a useless error argument, but proposed
MTU value, that is passed to tcp_mss_update() as mtuoffer.
Reported by: az
Reported by: Andrey Zonov <andrey zonov.org>
Reviewed by: andre (previous version of patch)
Before r228267 the option was honored but the original content of
boot.config was not preserved. I tried to fix that but missed the idea.
Now the proper way of doing things is taken from i386/boo2.
Also, a comment is added to explain this a little bit unobvious
behavior.
Inspired by: jhb
MFC after: 5 days
* arge0 doesn't (yet) work via the switch PHY ports; I'm not sure why.
* arge1 maps to the WAN port. That works.
TODO:
* The PLL register needs a different (non-default) value for Gigabit
Ethernet. The board setup code needs to be extended a bit to allow
for non-default pll_1000 values - right now, those values come out
of hard-coded values in the per-chip set_pll_ge() routines.
Obtained from: Linux / OpenWRT
This may result in a bit of a throughput drop. However, any throughput
drop at this point should be investigated and root caused, as it's likely
because TX scheduling (all the way down to how preemption, scheduler work,
etc) is happening in a sub-optimal fashion.
This also makes it much more likely to be reloadable on a live machine.
Allocating 5120 TX ath_buf entries via contigmalloc is very unlikely
after a few hours of using X/Chromium.
dirty and murky past.
* Override the default cache line size to be something reasonable if
it's set to 0. Some NICs initialise with '0' (eg embedded ones)
and there are comments in the driver stating that various OSes (eg
older Linux ones) would incorrectly program things and 0 out this
register.
* Just default to overriding the latency timer. Every other driver
does this.
* Use a default cache line size of 32 bytes. It should be "reasonable
enough".
Obtained from: Linux ath9k, Atheros
a8af6270bd96be6ccd86f70b60fa6512b710e4f0
virtio_blk: Include function name in panic string
cbdb03a694b76c5253d7ae3a59b9995b9afbb67a
virtio_balloon: Do the notify outside of the lock
By the time we return from virtqueue_notify(), the descriptor
will be in the used ring so we shouldn't have to sleep.
10ba392e60692529a5cbc1e9987e4064e0128447
virtio: Use DEVMETHOD_END
80cbcc4d6552cac758be67f0c99c36f23ce62110
virtqueue: Add support for VIRTIO_F_RING_EVENT_IDX
This can be used to reduce the number of guest/host and
host/guest interrupts by delaying the interrupt until a
certain index value is reached.
Actual use by the network driver will come along later.
8fc465969acc0c58477153e4c3530390db436c02
virtqueue: Simplify virtqueue_nused()
Since the values just wrap naturally at UINT16_MAX, we
can just subtract the two values directly, rather than
doing 2's complement math.
a8aa22f25959e2767d006cd621b69050e7ffb0ae
virtio_blk: Remove debugging crud from 75dd732a
There seems to be an issue with Qemu (or FreeBSD VirtIO) that sets
the PCI register space for the device config to bogus values. This
only seems to happen after unloading and reloading the module.
d404800661cb2a9769c033f8a50b2133934501aa
virtio_blk: Use better variable name
75dd732a97743d96e7c63f7ced3c2169696dadd3
virtio_blk: Partially revert 92ba40e65
Just use the virtqueue to determine if any requests are
still inflight.
06661ed66b7a9efaea240f99f414c368f1bbcdc7
virtio_blk: error if allowed too few segments
Should never happen unless the host provides use with a
bogus seg_max value.
4b33e5085bc87a818433d7e664a0a2c8f56a1a89
virtio_blk: Sort function declarations
426b9f5cac892c9c64cc7631966461514f7e08c6
virtio_blk: Cleanup whitespace
617c23e12c61e3c2233d942db713c6b8ff0bd112
virtio_blk: Call disk_err() on error'd completed requests
081a5712d4b2e0abf273be4d26affcf3870263a9
virtio_blk: ASSERT the ready and inflight request queues are empty
a9be2631a4f770a84145c18ee03a3f103bed4ca8
virtio_blk: Simplify check for too many segments
At the cost of a small style violation.
e00ec09da014f2e60cc75542d0ab78898672d521
virtio_blk: Add beginnings of suspend/resume
Still not sure if we need to virtio_stop()/virtio_reinit()
the device before/after a suspend.
Don't start additional IO when marked as suspending.
47c71dc6ce8c238aa59ce8afd4bda5aa294bc884
virtio_blk: Panic when dealt an unhandled BIO cmd
1055544f90fb8c0cc6a2395f5b6104039606aafe
virtio_blk: Add VQ enqueue/dequeue wrappers
Wrapper functions managed the added/removing to the in-flight
list of requests.
Normally biodone() any completed IO when draining the virtqueue.
92ba40e65b3bb5e4acb9300ece711f1ea8f3f7f4
virtio_blk: Add in-flight list of requests
74f6d260e075443544522c0833dc2712dd93f49b
virtio_blk: Rename VTBLK_FLAG_DETACHING to VTBLK_FLAG_DETACH
7aa549050f6fc6551c09c6362ed6b2a0728956ef
virtio_blk: Finish all BIOs through vtblk_finish_bio()
Also properly set bio_resid in the case of errors. Most geom_disk
providers seem to do the same.
9eef6d0e6f7e5dd362f71ba097f2e2e4c3744882
Added function to translate VirtIO status to error code
ef06adc337f31e1129d6d5f26de6d8d1be27bcd2
Reset dumping flag when given unexpected parameters
393b3e390c644193a2e392220dcc6a6c50b212d9
Added missing VTBLK_LOCK() in dump handler
Obtained from: Bryan Venteicher bryanv at daemoninthecloset dot org
r233961:
Fix interrupt load balancing regression, introduced in revision
222813, that left all un-pinned interrupts assigned to CPU 0.
In intr_shuffle_irqs(), remove CPU_SETOF() call that initialized
the "intr_cpus" cpuset to only contain CPU0.
This initialization is too late and nullifies the results of calls
to the intr_add_cpu() that occur much earlier in the boot process.
r234074 (partial):
The BSP is not added to the mask of valid target CPUs for interrupts.
Fix this by adding the BSP as an interrupt target directly in
r234105:
Fix !SMP build after r234074.
MFC after: 3 days
Contrarily to what i wrote in my previous commit, the 82599
does include the CRC in the length. The operating mode is
reset in ixgbe_init_locked() and so we need to hook into
the places where the two registers (HLREG0 and RDRXCTL) are
modified.
This uses the new firmware(9) method for squirreling away the EEPROM
contents from SPI flash so ath(4) can get to them later.
It won't work out of the box just yet - you have to add this to
if_ath_pci.c:
#define ATH_EEPROM_FIRMWARE
.. until I've added it as a configuration option and updated things.
interface.
* Introduce a device hint, 'eeprom_firmware', which is the name of firmware
to lookup.
* If the lookup succeeds, take a copy of it and use it as the eeprom data.
This isn't enabled by default - you have to define ATH_EEPROM_FIRMWARE.
I'll add it to the configuration variables in a later commit.
TODO:
* just keep a firmware reference in ath_softc, and remove the need to
waste the extra memory in having sc_eepromdata be a malloc()ed block.
future use by the ath(4) driver.
These embedded devices put the calibration/PCI bootstrap data on the
on board SPI flash rather than on an EEPROM connected to the NIC.
For some boards, there's two NICs and two sets of EEPROM data in the
main SPI flash.
The particulars:
* Introduce ath_fixup_size, which is the size of the EEPROM area in
bytes.
* Create a firmware image with a name based on the PCI device identifier
(bus/slot/device/function).
* Hide some verbose debugging behind 'bootverbose'.
ath(4) can then use this to load in the EEPROM data.
This requires AR71XX_ATH_EEPROM to be defined.
* the openwrt code doesn't treat 0/0/0 any differently
from other bus/slot/func combinations.
* A "local write" function writes to the LCONF area, and
so I've added it.
* The PCI workaround at attach time uses this LCONF code,
which it already did ..
* .. but it is a 4 byte write, not a 2 byte write.
Even though it's PCIR_COMMAND which is a two byte PCI register.
Tested on: AR7161
TODO: The other two AR71xx derivatives
TODO: More thoroughly stare at the datasheets I do have
and if it indeed is incorrect, push fixes to both
FreeBSD and Linux/OpenWRT.
Obtained from: Linux OpenWRT
Return EPERM from ext2_setattr() when an user without PRIV_VFS_SYSFLAGS
privilege attempts to toggle SF_SETTABLE flags.
Flags are now stored to ip->i_flags in one place after all checks.
Also, remove SF_NOUNLINK from the checks because ext2fs doesn't support
that flag.
Reviewed by: bde
It is implemented via db_trace_thread() for DDB and not implemented
for GDB. This should have been part of r234190.
Pointy hat to: jhb
Reported by: jkim
MFC after: 1 week
used in polled-mode. The callout invokes uart_intr, which rearms the timeout.
Implemented for bhyve, but generically useful for e.g. embedded bringup
when the interrupt controller hasn't been setup, or if it's not deemed
worthy to wire an interrupt line from a serial port.
Submitted by: neel
Reviewed by: marcel
Obtained from: NetApp
MFC after: 3 weeks
backtrace for an arbitrary thread (rather than the calling thread).
A kdb_backtrace_thread() wrapper function uses the configured debugger
if possible, otherwise it falls back to using stack(9) if that is
available.
- Replace a direct call to db_trace_thread() in propagate_priority()
with a call to kdb_backtrace_thread() instead.
MFC after: 1 week
fail to load (the MOD_LOAD event fails) during a kldload(2), unload the
linker file and fail the kldload(2) with ENOEXEC.
Reported by: gcooper
MFC after: 1 week
does not include the CRC irrespective of the setting
of CRCSTRIP. The 82599 data sheets (sec. 7.1.6) say differently.
Very strange. Need to check what happens on legacy descriptors,
but for the time being this restores functionality.
- Mark 'sdp' as requiring 'inet'.
- Always include "opt_inet.h" and "opt_inet6.h" and modify the IB
driver Makefiles to honor WITH/WITHOUT_INET/INET6/_SUPPORT options
to determine what should be enabled during a module build.
- Fix the mlxen(4) driver and the core IB code to compile without
if INET is disabled (including when both INET and INET6 are disabled).
Reviewed by: bz
MFC after: 2 weeks
in IFQ_HANDOFF() when the packet is passed to the start routine, so doing
it here resulted in double counting.
Reported by: Alex Tutubalin lexa lexa ru
MFC after: 1 week
table aren't valid. If they are ok, use hdr_lba_alt value to read backup
header. This will make gptboot happy when GPT used atop of some GEOM
provider, e.g. GEOM_MIRROR.
Reviewed by: pjd
MFC after: 2 weeks
and make it easier to replace it with a different implementation.
On passing, also fix indentation.
NOTE: I know that #include "foo.c" is ugly, but the alternative
(add another entry to sys/conf/files, add a separate header with
structs and prototypes, and expose functions that are meant to
be private) looks even worse to me.
We need a more modular way to specify dependencies and build options.
in td_errno. Flag is supposed to be used by syscalls returning
EJUSTRETURN because errno was already placed into the usermode frame
by a call to set_syscall_retval(9). Both ktrace and dtrace get errno
value from td_errno if the flag is set.
Use the flag to fix sigsuspend(2) error return ktrace records.
Requested by: bde
MFC after: 1 week
are discarded, this is an issue because lacp drops the lock which may allow
network threads to access freed memory. Expand the lock coverage so the
detach/attach happen atomically.
Submitted by: Andrew Boyer (earlier version)
static and declare its prototype in sys/vnode.h) so that it can be
called from process_deferred_inactive() (in ufs/ffs/ffs_snapshot.c)
instead of the body of vinactive() being cut and pasted into
process_deferred_inactive().
Reviewed by: kib
MFC after: 2 weeks
for whether the page is physical. On dense phys mem systems (32-bit),
VM_PHYS_TO_PAGE will not return NULL for device memory pages if device
memory is above physical memory even if there is no allocated vm_page.
Attempting to use the returned page could then cause either memory
corruption or a page fault.
portions were already reapplied in r233708:
- Use a dedicated task to handle deferred transmits from the if_transmit
method instead of reusing the existing per-queue interrupt task.
Reusing the per-queue interrupt task could result in both an interrupt
thread and the taskqueue thread trying to handle received packets on a
single queue resulting in out-of-order packet processing.
- Call ether_ifdetach() earlier in igb_detach().
- Drain tasks and free taskqueues during igb_detach().
MFC after: 1 week
being attached. This is implemented by adding a new DS_ATTACHING state
while a device's DEVICE_ATTACH() method is being invoked. A driver is
required to not fail an attach of a busy device. The device's state will
be promoted to DS_BUSY rather than DS_ACTIVE() if the device was marked
busy during DEVICE_ATTACH().
Reviewed by: kib
MFC after: 1 week
- add a sysctl, dev.netmap.ix_crcstrip, to control whether ixgbe should
strip the CRC on received frames. Defaults to 0, which keeps the CRC.
and improves performance when receiving min-sized (64-byte) frames.
This matters because min-sized frames is one of the standard
benchmarks for switches and routers, some chipsets seem to issue
read-modify-write cycles for PCIe transactions that are not a
full cache line, and a min-sized frame triggers the bug, resulting
in reduced throughput -- 9.7 instead of 14.88 Mpps -- and heavy
bus load.
- for the time being, always look for incoming packets on a select/poll
even if there has not been an interrupt in the meantime. This is
only a temporary workaround for a probable race condition in keeping
track of rx interrupts.
Add a couple of diagnostic vars to help studying the problem.
values as in the Intel driver 3.8.21 for linux. The fact that it
is standard in the above driver suggests that it has no bad side
effects.
But of course there must be a reason for enabling features, not
just "it does not harm", so here it is a good one:
Prefetching enables full line rate even using a single queue (14.88
Mpps, compared to ~12 Mpps without prefetch). This in turn is
terribly useful when one wants to schedule traffic.
For obvious reasons the difference is only visible with netmap
or other high speed solutions, but presumably the advantage
should be in the order of a fraction of a microsecond when
starting transmission on an empty queue.
Discussed with Jack Vogel.
MFC after: 1 week
outside the range of valid file descriptors
PR: kern/164970
Submitted by: Peter Jeremy <peterjeremy@acm.org>
Reviewed by: jilles
Approved by: cperciva
MFC after: 1 week
we look at count of addresses on a particular vhid, we
should account number of addresses on cif.
To achieve this we need to run carp_attach() and
carp_detach() under appropriate cif lock.
r228476 fixed superfluous link UP/DOWN messages but broke IPMI
access during boot. It's not clear why r228476 breaks IPMI and
should be revisited.
Reported by: Paul Guyot <paulguyot <> ieee dot org >
MFC after: 1 week
identical now that the bus spaces are unified under sys/x86.
Replace them with a single uart_cpu_x86.c.
o delete uart_cpu_i386.c
o move uart_cpu_amd64.c to uart_cpu_x86.c
o update files.amd64 and files.i386 accordingly.
usermode context switches (long jumps and ucontext operations). If these
are used across threads, multiple threads can end up with the same TLS base.
Madness will then result.
This makes behavior on PPC match that on x86 systems and on Linux.
MFC after: 10 days
problem where userspace apps such as smartctl fail due to CAM_REQUEUE_REQ
status getting returned when tagged commands are outstanding when smartctl
sends its I/O using the pass(4) interface.
Sponsored by: Intel
Found and tested by: Ravi Pokala <rpokala at panasas dot com>
Reviewed by: scottl
Approved by: scottl
MFC after: 1 week
- Use more natural ip->i_flags instead of vap->va_flags in the final
flags check.
- Style improvements.
No functional change intended.
MFC after: 2 weeks
privilege attempts to toggle SF_SETTABLE flags.
- Use the '^' operator in the SF_SNAPSHOT anti-toggling check.
Flags are now stored to ip->i_flags in one place after all checks.
Submitted by: bde
add a FreeBSD_version check. It should work fine for compiling
on -HEAD, 9.x and 8.x.
* Conditionally compile the 11n options only when 11n is enabled.
The above changes allow the ath(4) driver to compile and run on
8.1-RELEASE (Hi old PC-BSD!) but with the 11n stuff disabled.
I've done a test against the net80211 and tools in 8.1-RELEASE.
The NIC used in testing is the AR2427 in an EEEPC.
Just to be clear - this change is to allow the -HEAD ath/hal/rate
code to run on 9.x _and_ 8.x with no source changes. However,
when running on earlier kernels, it should only be used for legacy
mode. (Don't define ATH_ENABLE_11N.)
this commit is not enough to enable CARP operation on
if_bridge(4), because the latter doesn't handle or even
initialize its ifp->if_link_state.
Reported by: Alexander Lunev <sol289 gmail.com>
in set_apic_interrupt_ids(). Besides, set_apic_interrupts_ids() is not
called in the !SMP case too.
Fix this by:
- Adding the BSP as an interrupt target directly in cpu_startup().
- Remove an obsolete optimization where the BSP are skipped in
set_apic_interrupt_ids().
Reported by: jh
Reviewed by: jhb
MFC after: 3 days
X-MFC: r233961
Pointy hat to: me
The SA_PROC signal property indicated whether each signal number is directed
at a specific thread or at the process in general. However, that depends on
how the signal was generated and not on the signal number. SA_PROC was not
used.
accesses of the cache member of vm_object objects.
- Use novel vm_page_is_cached() for checks outside of the vm subsystem.
Reviewed by: alc
MFC after: 2 weeks
X-MFC: r234039
They do not have compatible configuration registers in PCI configuration
space. Instead their configuration resides in AMD "PM I/O" space
(accessed via a pair of I/O space registers).
MFC after: 5 days
that it will be freed to the cache pool rather than the default pool.
Otherwise, the cached pages within the reservation may be recycled sooner
than necessary.
Reported by: Andrey Zonov
policy configuration, avoid leaking resources following failed calls
to get and set MAC labels by file descriptor.
Reported by: Mateusz Guzik <mjguzik at gmail.com> + clang scan-build
MFC after: 3 days
accounting for I/O counts at completion of I/O operation. Also switch
from using global devmtx to vnode mutex to reduce contention.
Suggested and reviewed by: kib
damage which I committed when I had less clue about such things.
Don't ever put normal data frames on the mcast software queue.
Just put mcast frames there if needed.
Pass the txq decision into ath_tx_normal_setup(), as we've already made
the decision. Don't re-do it.
Whilst i'm here, add another random debugging statement.
used in the code which needs to implement some specific
behaviour when being run under QEMU.
- Make PXA UART probe code to work under QEMU gumstix, which
doesn't emulate all the ports properly.
allocator.
Replace UINT32_MAX checks with INT_MAX. Keeping more than 2^31 nodes in
memory is not likely to become possible in foreseeable feature and would
require new unit number allocator.
Discussed with: delphij
MFC after: 2 weeks
This fixes bootp on if_smc, as bootp code perform SIOCSIFADDR
ioctl call immediately after sending the request (which causes
if_init being called) which causes the adapter to drop all the
packets received in the meantime.
call these after rate control selection is done.
The duration/protection code wasn't working - it expected the rix to
be valid. Unfortunately after I moved the rate control selection into
late in the process, the rix value isn't valid and thus the protection/
duration code would get things wrong.
HT frames are now correctly protected with an RTS and for the AR5416,
this involves having the aggregate frames be limited to 8K.
TODO:
* Fix up the DMA sync to occur just before the frame is queued to the
hardware. I'm adjusting the duration here but not doing the DMA
flush.
* Doubly/triply ensure that the aggregate frames are being limited to
the correct size, or the AR5416 will get unhappy when TXing RTS-protected
aggregates.
if any subframes in an aggregate have different protection from the
first frame in the formed aggregate, don't add that frame to the
aggregate.
This is likely a suboptimal method (I think we'll mostly be OK marking
frames that have seqno's with the same protection as normal data frames)
but I'll just be cautious for now.
This will be used by some upcoming code to ensure that aggregates
are enforced to be a certain size. The AR5416 has a limitation on
RTS protected aggregates (8KiB).
that don't exist.
Anecdotal evidence indicates that it is better to return 011b (bad LUN)
than 001b (LUN offline). However, this change also gives the user a
sysctl/tunable, kern.cam.ctl.inquiry_pq_no_lun, to override the change
and return to the previous behavior. (The previous behavior was to
return 001b, or LUN offline.)
ctl.c: Change the default inquiry peripheral qualifier to 011b,
and add a sysctl and tunable to allow the user to change
it back to 001b if needed.
Don't insert a Copan copyright statement in the inquiry
data. The copyright statements on the files are
sufficient.
ctl_private.h: Add sysctl variable context to the CTL softc.
ctl_cmd_table.c,
ctl_frontend_internal.c,
ctl_frontend.c,
ctl_backend.c,
ctl_error.c: Include sys/sysctl.h.
MFC after: 3 days
222813, that left all un-pinned interrupts assigned to CPU 0.
sys/x86/x86/intr_machdep.c:
In intr_shuffle_irqs(), remove CPU_SETOF() call that initialized
the "intr_cpus" cpuset to only contain CPU0.
This initialization is too late and nullifies the results of calls
the intr_add_cpu() that occur much earlier in the boot process.
Since "intr_cpus" is statically initialized to the empty set, and
all processors, including the BSP, already add themselves to
"intr_cpus" no special initialization for the BSP is necessary.
MFC after: 3 days
(slightly) different semantics and renaming it prevents a (harmless)
WITNESS warning during bootup for 32-bit kernels on 64-bit CPUs.
MFC after: 5 days
The menu item is now made completely independent with the ACPI item - most
modern systems seem to require ACPI and become even more "unsafe"
without it.
Safe Mode no longer disables APIC for the same reason.
kbdmux is not disabled as this feature has proven itself stable.
New actions:
- SMP is disabled in the Safe Mode now
- eventtimers are forced to periodic mode (some real and virtual systems
seem to have problems otherwise)
- geom extra vigorous integrity checking is disabled, this is to
facilitate migration from previous versions
Possible short term to do:
- make SMP switch a separate menu item
- restore APIC switch as a separate menu item
Longer term to do:
- turn various tweaks into separate menu items in a Safe Mode sub-menu
Please consider adding a safety tweak to Safe Mode when introducing
new major features or changes that may cause instabilities.
Discussed with: jhb, scottl, Devin Teske
MFC after: 3 weeks (stable/9 only)
Linux and Solaris (at least OpenSolaris) has PF_PACKET socket families to send
raw ethernet frames. The only FreeBSD interface that can be used to send raw frames
is BPF. As a result, many programs like cdpd, lldpd, various dhcp stuff uses
BPF only to send data. This leads us to the situation when software like cdpd,
being run on high-traffic-volume interface significantly reduces overall performance
since we have to acquire additional locks for every packet.
Here we add sysctl that changes BPF behavior in the following way:
If program came and opens BPF socket without explicitly specifyin read filter we
assume it to be write-only and add it to special writer-only per-interface list.
This makes bpf_peers_present() return 0, so no additional overhead is introduced.
After filter is supplied, descriptor is added to original per-interface list permitting
packets to be captured.
Unfortunately, pcap_open_live() sets catch-all filter itself for the purpose of
setting snap length.
Fortunately, most programs explicitly sets (event catch-all) filter after that.
tcpdump(1) is a good example.
So a bit hackis approach is taken: we upgrade description only after second
BIOCSETF is received.
Sysctl is named net.bpf.optimize_writers and is turned off by default.
- While here, document all sysctl variables in bpf.4
Sponsored by Yandex LLC
Reviewed by: glebius (previous version)
Reviewed by: silence on -net@
Approved by: (mentor)
MFC after: 4 weeks
Interface locks and descriptor locks are converted from mutex(9) to rwlock(9).
This greately improves performance: in most common case we need to acquire 1
reader lock instead of 2 mutexes.
- Remove filter(descriptor) (reader) lock in bpf_mtap[2]
This was suggested by glebius@. We protect filter by requesting interface
writer lock on filter change.
- Cover struct bpf_if under BPF_INTERNAL define. This permits including bpf.h
without including rwlock stuff. However, this is is temporary solution,
struct bpf_if should be made opaque for any external caller.
Found by: Dmitrij Tejblum <tejblum@yandex-team.ru>
Sponsored by: Yandex LLC
Reviewed by: glebius (previous version)
Reviewed by: silence on -net@
Approved by: (mentor)
MFC after: 3 weeks
a pair of records similar to syscall entry and return that a user can
use to determine how long page faults take. The new ktrace records are
enabled via the 'p' trace type, and are enabled in the default set of
trace points.
Reviewed by: kib
MFC after: 2 weeks
On FreeBSD the direct ioctl argument is automatically copied in/out
as necesary by the kernel ioctl entry point.
PR: kern/164445
Submitted by: Luis Garces-Erice <lge@ieee.org>
Tested by: Attila Nagy <bra@fsn.hu>
MFC after: 5 days
application destroys semaphore after sem_wait returns. Just enter
kernel to wake up sleeping threads, only update _has_waiters if
it is safe. While here, check if the value exceed SEM_VALUE_MAX and
return EOVERFLOW if this is true.
a mutex after a thread has unlocked it, it event writes data to the mutex
memory to clear contention bit, there is a race that other threads
can lock it and unlock it, then destroy it, so it should not write
data to the mutex memory if there isn't any waiter.
The new operation UMTX_OP_MUTEX_WAKE2 try to fix the problem. It
requires thread library to clear the lock word entirely, then
call the WAKE2 operation to check if there is any waiter in kernel,
and try to wake up a thread, if necessary, the contention bit is set again
by the operation. This also mitgates the chance that other threads find
the contention bit and try to enter kernel to compete with each other
to wake up sleeping thread, this is unnecessary. With this change, the
mutex owner is no longer holding the mutex until it reaches a point
where kernel umtx queue is locked, it releases the mutex as soon as
possible.
Performance is improved when the mutex is contensted heavily. On Intel
i3-2310M, the runtime of a benchmark program is reduced from 26.87 seconds
to 2.39 seconds, it even is better than UMTX_OP_MUTEX_WAKE which is
deprecated now. http://people.freebsd.org/~davidxu/bench/mutex_perf.c
A BAR frame must be transmitted when an frame in an A-MPDU session fails
to transmit - it's retried too often, or it can't be cloned for
re-transmission. The BAR frame tells the remote side to advance the
left edge of the block-ack window (BAW) to a new value.
In order to do this:
* TX for that particular node/TID must be paused;
* The existing frames in the hardware queue needs to be completed, whether
they're TXed successfully or otherwise;
* The new left edge of the BAW is then communicated to the remote side
via a BAR frame;
* Once the BAR frame has been sucessfully TXed, aggregation can resume;
* If the BAR frame can't be successfully TXed, the aggregation session
is torn down.
This is a first pass that implements the above. What needs to be done/
tested:
* What happens during say, a channel reset / stuck beacon _and_ BAR
TX. It _should_ be correctly buffered and retried once the
reset has completed. But if a bgscan occurs (and they shouldn't,
grr) the BAR frame will be forcibly failed and the aggregation session
will be torn down.
Yes, another reason to disable bgscan until I've figured this out.
* There's way too much locking going on here. I'm going to do a couple
of further passes of sanitising and refactoring so the (re) locking
isn't so heavy. Right now I'm going for correctness, not speed.
* The BAR TX can fail if the hardware TX queue is full. Since there's
no "free" space kept for management frames, a full TX queue (from eg
an iperf test) can race with your ability to allocate ath_buf/mbufs
and cause issues. I'll knock this on the head with a subsequent
commit.
* I need to do some _much_ more thorough testing in hostap mode to ensure
that many concurrent traffic streams to different end nodes are correctly
handled. I'll find and squish whichever bugs show up here.
But, this is an important step to being able to flip on 802.11n by default.
The last issue (besides bug fixes, of course) is HT frame protection and
I'll address that in a subsequent commit.
Linux ath9k doesn't have this issue as it doesn't try queuing multi-
descriptor frames to the hardware.
Before, I was only setting the first and last descriptor in the final
frame correctly - and that was done by accident. The first descriptor in
the last sub-frame was being correctly updated by ath_tx_setds_11n();
the last descriptor in the last sub-frame was being correctly updated
by ath_buf_set_rate(). But both of those are "incorrect".
The correct behaviour is:
* AR_IsAggr is set for all descriptors for all subframes in an aggregate.
* AR_MoreAggr is set for all descriptors for all non-final sub-frames
in an aggregate.
Ie, all descriptors in the last sub-frame of an aggregate must have this
field set to 0.
I still need to do a couple of extra passes to ensure the pad delimiter
field is being correctly handled in all descriptors in the last sub-frame.
can be upgraded to MegaRAID mode, in which case mfi(4) should attach to
these based on the sub-vendor and -device ID instead (not currently done).
Therefore, let mpt_pci_probe() return BUS_PROBE_LOW_PRIORITY.
While it, let mpt_pci_probe() return BUS_PROBE_DEFAULT instead of 0 in
the default case.
MFC after: 3 days
revision 1.173
date: 2011/11/09 12:36:03; author: camield; state: Exp; lines: +11 -12
State expire time is a baseline time ("last active") for expiry
calculations, and does _not_ denote the time when to expire. So
it should never be added to (set into the future).
Try to reconstruct it with an educated guess on state import and
just set it to the current time on state updates.
This fixes a problem on pfsync listeners where the expiry time
could be double the expected value and cause a lot more states
to linger.
forwarding a packet, that creates state, until
pfsync(4) peer acks state addition (or 10 msec
timeout passes).
This is needed for active-active CARP configurations,
which are poorly supported in FreeBSD and arguably
a good idea at all.
Unfortunately by the time of import this feature in
OpenBSD was turned on, and did not have a switch to
turn it off. This leaked to FreeBSD.
This change make it possible to turn this feature
off via ioctl() and turns it off by default.
Obtained from: OpenBSD
and it is no longer referenced by a user process. The inode for a
file whose name has been removed, but is still referenced at the
time of a crash will still be allocated in the filesystem, but will
have no references (e.g., they will have no names referencing them
from any directory).
With traditional soft updates these unreferenced inodes will be
found and reclaimed when the background fsck is run. When using
journaled soft updates, the kernel must keep track of these inodes
so that it can find and reclaim them during the cleanup process.
Their existence cannot be stored in the journal as the journal only
handles short-term events, and they may persist for days. So, they
are tracked by keeping them in a linked list whose head pointer is
stored in the superblock. The journal tracks them only until their
linked list pointers have been commited to disk. Part of the cleanup
process involves traversing the list of unreferenced inodes and
reclaiming them.
This bug was triggered when confusion arose in the commit steps
of keeping the unreferenced-inode linked list coherent on disk.
Notably, a race between the link() system call adding a link-count
to a file and the unlink() system call removing a link-count to
the file. Here if the unlink() ran after link() had looked up
the file but before link() had incremented the link-count of the
file, the file's link-count would drop to zero before the link()
incremented it back up to one. If the file was referenced by a
user process, the first transition through zero made it appear
that it should be added to the unreferenced-inode list when in
fact it should not have been added. If the new name created by
link() was deleted within a few seconds (with the file still
referenced by a user process) it would legitimately be a candidate
for addition to the unreferenced-inode list. The result was that
there were two attempts to add the same inode to the unreferenced-inode
list which scrambled the unreferenced-inode list's pointers leading
to a panic. The fix is to detect and avoid the false attempt at
adding it to the unreferenced-inode list by having the link()
system call check to see if the link count is zero before it
increments it. If it is, the link() fails with ENOENT (showing that
it has failed the link()/unlink() race).
While tracking down this bug, we have added additional assertions
to detect the problem sooner and also simplified some of the code.
Reported by: Kirk Russell
Fix submitted by: Jeff Roberson
Tested by: Peter Holm
PR: kern/159971
MFC (to 9 only): 2 weeks
sleeping from a swi handler (even though in this case it would be ok), so
switch the refill and scanning SWI handlers to being tasks on a fast
taskqueue. Also, only schedule the refill task for a CMCI as an MC# can
fire at any time, so it should do the minimal amount of work needed and
avoid opportunities to deadlock before it panics (such as scheduling a
task it won't ever need in practice). To handle the case of an MC# only
finding recoverable errors (which should never happen), always try to
refill the event free list when the periodic scan executes.
MFC after: 2 weeks
flags check.
- Add a comment for the immutable/append check done after handling of
the flags.
- Style improvements.
No functional change intended.
Submitted by: bde
MFC after: 2 weeks
an uncorrected ECC error tends to fire on all CPUs in a package
simultaneously and the current printf hacks are not sufficient to make
the messages legible. Instead, use the existing mca_lock spinlock to
serialize calls to mca_log() and change the machine check code to panic
directly when an unrecoverable error is encoutered rather than falling
back to a trap_fatal() call in trap() (which adds nearly a screen-full of
logging messages that aren't useful for machine checks).
MFC after: 2 weeks
via procstat(1) and fstat(1):
- Change shm file descriptors to track the pathname they are associated
with and add a shm_path() method to copy the path out to a caller-supplied
buffer.
- Use the fo_stat() method of shared memory objects and shm_path() to
export the path, mode, and size of a shared memory object via
struct kinfo_file.
- Add a struct shmstat to the libprocstat(3) interface along with a
procstat_get_shm_info() to export the mode and size of a shared memory
object.
- Change procstat to always print out the path for a given object if it
is valid.
- Teach fstat about shared memory objects and to display their path,
mode, and size.
MFC after: 2 weeks
checked PROTECT bit in INQUIRY data for all SPC devices, while it is defined
only since SPC-3. But there are some SPC-2 USB devices were reported, that
have PROTECT bit set, return no error for READ CAPACITY(16) command, but
return wrong sector count value in response.
MFC after: 3 days
First cut of new HW support from LSI and merge into FreeBSD.
Supports Drake Skinny and ThunderBolt cards.
MFhead_mfi r227574
Style
MFhead_mfi r227579
Use bus_addr_t instead of uintXX_t.
MFhead_mfi r227580
MSI support
MFhead_mfi r227612
More bus_addr_t and remove "#ifdef __amd64__".
MFhead_mfi r227905
Improved timeout support from Scott.
MFhead_mfi r228108
Make file.
MFhead_mfi r228208
Fixed botched merge of Skinny support and enhanced handling
in call back routine.
MFhead_mfi r228279
Remove superfluous !TAILQ_EMPTY() checks before TAILQ_FOREACH().
MFhead_mfi r228310
Move mfi_decode_evt() to taskqueue.
MFhead_mfi r228320
Implement MFI_DEBUG for 64bit S/G lists.
MFhead_mfi r231988
Restore structure layout by reverting the array header to
use [0] instead of [1].
MFhead_mfi r232412
Put wildcard pattern later in the match table.
MFhead_mfi r232413
Use lower case for hexadecimal numbers to match surrounding
style.
MFhead_mfi r232414
Add more Thunderbolt variants.
MFhead_mfi r232888
Don't act on events prior to boot or when shutting down.
Add hw.mfi.detect_jbod_change to enable or disable acting
on JBOD type of disks being added on insert and removed on
removing. Switch hw.mfi.msi to 1 by default since it works
better on newer cards.
MFhead_mfi r233016
Release driver lock before taking Giant when deleting children.
Use TAILQ_FOREACH_SAFE when items can be deleted. Make code a
little simplier to follow. Fix a couple more style issues.
MFhead_mfi r233620
Update mfi_spare/mfi_array with the actual number of elements
for array_ref and pd. Change these max. #define names to avoid
name space collisions. This will require an update to mfiutil
It avoids mfiutil having to do a magic calculation.
Add a note and #define to state that a "SYSTEM" disk is really
what the firmware calls a "JBOD" drive.
Thanks to the many that helped, LSI for the initial code drop,
mav, delphij, jhb, sbruno that all helped with code and testing.
sys/dev/isci/isci_task_request.c:198:7: error: case value not in enumerated type 'SCI_TASK_STATUS' (aka 'enum _SCI_TASK_STATUS') [-Werror,-Wswitch]
case SCI_FAILURE_TIMEOUT:
^
This is because the switch is done on a SCI_TASK_STATUS enum type, but
the SCI_FAILURE_TIMEOUT value belongs to SCI_STATUS instead.
Because the list of SCI_TASK_STATUS values cannot be modified at this
time, use the simplest way to get rid of this warning, which is to cast
the switch argument to int. No functional change.
Reviewed by: jimharris
MFC after: 3 days
- Don't malloc() new MCA records for machine checks logged due to a
CMCI or MC# exception. Instead, use a pre-allocated pool of records.
When a CMCI or MC# exception fires, schedule a swi to refill the pool.
The pool is sized to hold at least one record per available machine
bank, and one record per CPU. This should handle the case of all CPUs
triggering a single bank at once as well as the case a single CPU
triggering all of its banks. The periodic scans still use malloc()
since they are run from a safe context.
- Since we have to create an swi to handle refills, make the periodic scan
a second swi for the same thread instead of having a separate taskqueue
thread for the scans.
Suggested by: mdf (avoiding malloc())
MFC after: 2 weeks
- Do not define the foo_start() methods or set if_start in the ifnet if
multiq transmit is enabled. Also, set if_transmit and if_qflush before
ether_ifattach rather than after when multiq transmit is enabled. This
helps to ensure that the drivers never try to mix different transmit
methods.
- Properly restart transmit during resume. igb(4) was not restarting it
at all, and em(4) was restarting even if the link was down and was
calling the wrong method if multiq transmit was enabled.
- Remove all the 'more' handling for transmit completions. Transmit
completion processing does not have a processing limit, so it always
runs to completion and never has more work to do when it returns.
Instead, the previous code was returning 'true' anytime there were
packets in the queue that weren't still in the process of being
transmitted. The effect was that the driver would continuously
reschedule a task to process TX completions in effect running at 100%
CPU polling the hardware until it finished transmitting all of the
packets in the ring. Now it will just wait for the next TX completion
interrupt.
- Restart packet transmission when the link becomes active.
- Fix the MSI-X queue interrupt handlers to restart packet transmission if
there are pending packets in the relevant software queue (IFQ or buf_ring)
after processing TX completions. This is the root cause for the OACTIVE
hangs as if the MSI-X queue handler drained all the pending packets from
the TX ring, nothing would ever restart it. As such, remove some
previously-added workarounds to reschedule a task to poll the TX ring
anytime OACTIVE was set.
Tested by: sbruno
Reviewed by: jfv
MFC after: 1 week
"Under a highly specific and detailed set of internal timing conditions,
the processor may incorrectly update the stack pointer after a long series
of push and/or near-call instructions, or a long series of pop and/or
near-return instructions. The processor must be in 64-bit mode for this
erratum to occur."
MFC after: 3 days
- Correctly determine the maximum payload size for setting the TX link
frequent NACK latency and replay timer thresholds.
Submitted by: stefanf [1]
MFC after: 3 days
This change also workarounds dhclient's link state handling bug by
not giving current link status.
Unlike other controllers, ale(4)'s PHY hibernation perfectly works
such that driver does not see a valid link if the controller is not
brought up. If dhclient(8) runs on ale(4) it will blindly waits
until link UP and then gives up after 10 seconds. Because
dhclient(8) still thinks interface got a valid link when IFM_AVALID
is not set for selected media, this change makes dhclient initiate
DHCP without waiting for link UP.
needs to defer link state handling.
While I'm here, mark IFF_DRV_RUNNING before changing media. If
link is established without any delay, that link state change
handling could be lost.
that revision, the bswapXX_const() macros were renamed to bswapXX_gen().
Also, bswap64_gen() was implemented as two calls to bswap32(), and
similarly, bswap32_gen() as two calls to bswap16(). This mainly helps
our base gcc to produce more efficient assembly.
However, the arguments are not properly masked, which results in the
wrong value being calculated in some instances. For example,
bswap32(0x12345678) returns 0x7c563412, and bswap64(0x123456789abcdef0)
returns 0xfcdefc9a7c563412.
Fix this by appropriately masking the arguments to bswap16() in
bswap32_gen(), and to bswap32() in bswap64_gen(). This should also
silence warnings from clang.
Submitted by: jh
revision has two problems:
- It can produce worse code with both clang and gcc.
- It doesn't fix the actual issue introduced in r232721, which will be
fixed in the next commit.
Submitted by: bde, tijl and jh
Pointy hat to: dim
not disable it and it is even harmful as hselasky found out. Historically,
this code was originated from (OLDCARD) CardBus driver and later leaked into
PCI driver when CardBus was newbus'ified and refactored with PCI driver.
However, it is not really necessary even for CardBus.
Reviewed by: hselasky, imp, jhb
bridges. Rather than blindly enabling the windows on all of them, only
enable the window when an MSI interrupt is enabled for a device behind
the bridge, similar to what already happens for HT PCI-PCI bridges.
To implement this, each x86 Host-PCI bridge driver has to be able to
locate it's actual backing device on bus 0. For ACPI, use the _ADR
method to find the slot and function of the device. For the non-ACPI
case, the legacy(4) driver already scans bus 0 looking for Host-PCI
bridge devices. Now it saves the slot and function of each bridge that
it finds as ivars that the Host-PCI bridge driver can then use in its
pcib_map_msi() method.
This fixes machines where non-MSI interrupts were broken by the previous
round of HT MSI changes.
Tested by: bapt
MFC after: 1 week
added, the call to pmap_kextract() was moved up, and as a result the
code never updated the physical address to use for DMA if a bounce
buffer was used. Restore the earlier location of pmap_kextract() so
it takes bounce buffers into account.
Tested by: kargl
MFC after: 1 week
Right now ath_txq_sched() is mainly called from the TX ath_tx_processq()
routine, which is (mostly) done as part of the taskqueue. It shouldn't
be called outside the taskqueue.
But now that I'm about to flip back on BAR TX, I'm going to start
stressing the ath_tx_tid_pause() and ath_tx_tid_resume() paths.
What I don't want to have happen is a reschedule of the TID traffic
_during_ the completion of TX frames.
Ideally I'd like to have a way to flag back up to the processing code
that the current hardware queue should be rechecked for software TID
queue frames. But for now, this should suffice for the BAR TX case.
I may eventually delete this code once I've brought some further
sanity to the general TX queue/completion path.
be less ambiguous and more clearly identify what it means. This
attribute is what Intel refers to as UC-, and it's only difference
relative to normal UC memory is that a WC MTRR will override a UC-
PAT entry causing the memory to be treated as WC, whereas a UC PAT
entry will always override the MTRR.
- Remove the VM_MEMATTR_UNCACHED alias from powerpc.
Don't disable BARs on any PCI display devices, because doing that can
sometimes cause the main memory bus to stop working, causing all
memory reads to return nothing but 0xFFFFFFFF, even though the memory
location was previously written. After a while a privileged
instruction fault will appear and then nothing more can be debugged.
The reason for this behaviour is unknown.
MFC after: 1 week
This makes our naming scheme more closely match other systems and the
expectations of much third-party software. MIPS builds which are little-endian
should require and exhibit no changes. Big-endian TARGET_ARCHes must be
changed:
From: To:
mipseb mips
mipsn32eb mipsn32
mips64eb mips64
An entry has been added to UPDATING and some foot-shooting protection (complete
with warnings which should become errors in the near future) to the top-level
base system Makefile.
