with the known bogus currtpriority. This undoes the previous changes to
sys/i386/i386/trap.c, sys/alpha/alpha/trap.c, sys/sys/systm.h
Now we have the patch set approved by bde.
Approved by: bde
was using them exits.
Don't allow a user process to cause the kernel to take a TRCTRAP on a
user space address.
Reviewed by: jlemon, sef
Approved by: jkh
chipset to be probed & attached on newer Dell PowerEdge servers, such as
the 2400 and 4400.
Reviewed by: dfr, msmith, jlemon
Tested by: hnokubi@yyy.or.jp (in a previous incantation)
Approved by: jkh
and Pentium III Xeon CPUs. If a CPU is one of Pentium II, Pentium II
Xeon and Celeron, the message is always "Pentium II/Pentium II
Xeon/Celeron". If a CPU is one of Pentium III and Pentium III Xeon,
the message is always "Pentium III/Pentium III Xeon".
o Drop all broadcast and multicast source addresses in tcp_input.
o Enable ICMP_BANDLIM in GENERIC.
o Change default to 200/s from 100/s. This will still stop the attack, but
is conservative enough to do this close to code freeze.
This is not the optimal patch for the problem, but is likely the least
intrusive patch that can be made for this.
Obtained from: Don Lewis and Matt Dillon.
Reviewed by: freebsd-security
IRQ 2 was being unilaterally disallowed, which is only appropriate if
the interrupt hardware is the traditional chained PIC arrangement.
Reviewed by: tegge (in principle)
activated. Some of the things that get listed as "resources" aren't
necessarily suited for this.
(This shouldn't be a problem for any driver that correctly passes
RF_ACTIVE)
NICs. (Finally!) The PCMCIA, ISA and PCI varieties are all supported,
though only the ISA and PCI ones will work on the alpha for now.
PCCARD, ISA and PCI attachments are all provided. Also provided an
ancontrol(8) utility for configuring the NIC, man pages, and updated
pccard.conf.sample. ISA cards are supported in both ISA PnP and hard-wired
mode, although you must configure the kernel explicitly to support the
hardwired mode since you have to know the I/O address and port ahead
of time.
Special thanks to Doug Ambrisko for doing the initial newbus hackery
and getting it to work in infrastructure mode.
USB-EL1202A chipset. Between this and the other two drivers, we should
have support for pretty much every USB ethernet adapter on the market.
The only other USB chip that I know of is the SMC USB97C196, and right
now I don't know of any adapters that use it (including the ones made
by SMC :/ ).
Note that the CATC chip supports a nifty feature: read and write combining.
This allows multiple ethernet packets to be transfered in a single USB
bulk in/out transaction. However I'm again having trouble with large
bulk in transfers like I did with the ADMtek chip, which leads me to
believe that our USB stack needs some work before we can really make
use of this feature. When/if things improve, I intend to revisit the
aue and cue drivers. For now, I've lost enough sanity points.
ddb is entered. Don't refer to `in_Debugger' to see if we
are in the debugger. (The variable used to be static in Debugger()
and wasn't updated if ddb is entered via traps and panic anyway.)
- Don't refer to `in_Debugger'.
- Add `db_active' to i386/i386/db_interface.d (as in
alpha/alpha/db_interface.c).
- Remove cnpollc() stub from ddb/db_input.c.
- Add the dbctl function to syscons, pcvt, and sio. (The function for
pcvt and sio is noop at the moment.)
Jointly developed by: bde and me
(The final version was tweaked by me and not reviewed by bde. Thus,
if there is any error in this commit, that is entirely of mine, not
his.)
Some changes were obtained from: NetBSD
${GEN_CFLAGS} and -U_KERNEL became negative when all all the
genassym.c's were converted to be cross-built.
Makefile.*:
- Cleanups associated with the old genassym.
- Fixed deprecated spelling of ${.IMPSRC} as "$<".
