Add support, kinda, for megaheartz xjack nic cards. This support
works well for one machine per ethernet segment because it hard codes
the MAC address. The pccardd in -current doesn't have support to
parse the ethernet address from the CIS in the funky way that the
megaheartz card does things (it includes it in the info tuple, as
ascii, which is non-standard). I'd rather kludge this for the moment
and work to read the CIS from the kernel rather than mess with
pccardd.
The isa attachment is untested. The pccard attachment is known to
work since I'm committing over it.
Card Obtained from: Chris D. Faulhaber <jedger@fxp.org>
- Don't keep private copies of some of the data fields from the
ENQUIRY and ENQUIRY2 commands. Instead, standardise on the ENQUIRY2
command for initial adapter information, and keep a copy of the entire
structure. Refer to it where appropriate.
- Move all of the controller description functionality into a new
function. Print lots more controller data if bootverbose is set.
Add knowledge of the DAC960 PR, PT, PTL0 and PRL controllers, rename
the 960PTL -> PTL0 and 1100P -> 1100PVX.
- Correctly terminate an error message.
The controller interface procedures have been reviewed against the
Mylex-supplied documentation; no changes appear necessary at this
time.
on all combinations (I hope)...
Add DMA support for the AMD 756 chip (K7 chipset) this is actually the
same as the VIA 82C686 chip (the ATA part that is).
Treat the intel MX chipset PIIX as a PIIX4
Allow UDMA on all disks that say they can handle it.
Cleanup probe printf's a bit
Remove alot of the old #ifdef DEBUG crap.
going to a lot of trouble to identify it and set the tag and then not use
it. Convert the pnp id matching to the preferred table based system.
@@@0001 (CMI8330 ldn 0) is a mss, not a SB.
of these are bound to have a PNP05xx compatid, but there's no easy way to
tell. Since it's just an ID list and uses the pnp header's description
strings rather than encoding strings here, it doesn't seem to be too
expensive to err on the safe side.
misdetecting FIFO capabilities, at least on my girlfriend's Thinkpad 755,
the driver doesn't work using the FIFO.
While i was at it, i (partially) fixed option FCC_YE since it would no
longer have compiled at all under -current. I've also made an attempt
to document the device driver flags value (ab-)used internally by this
option.
RELENG_3 candidate, but with a slightly different patch there (will go
to jkh in email).
or less. This is a kludge because there is no support for delayed
creation of threads early in the boot process.
NEWCARD new boots and the thread process starts and is visible from
ps.
Now, on to dev/pccard.
the input fifo to be returned as successful and frozen. Most, if not
all, peripheral drivers do not check the qfrozen bit for successfully
completed commands, so the result would not only be lost commands, but
devices locked out from receiving commands. This was a bad bug that
crept in two or three months ago during some target mode work.
config_intrhook_establish doesn't work. Children aren't yet attached
properly, but that's ok because pccard would likely panic in its
current shape.
o Save dev of pcic early in attach process
o save dev in pcic_handle for use in pcic_create_event_thread.
o Remove direct attachments of pccard children for now
o move establishment of pcic kthread to config_intrhook.
3.3R and then to -current. The pccard support has been left in the
driver, but is presently non-functional because we are using the
isa_compat layer for the moment.
Obtained From: PAO
Sponsored by: Timing Solutions
o minor formatting nits
o remove the bus_map/unmap calls. FreeBSD doesn't need them.
o Fix most of the compiler warnings remaining (some still remain, but they
are releated to calling functions that are going to change, so I did
not bother).
broken bit work-around enabled.
* Fixed a bug that made MDP not work. (However, MDP is actually not tested
due to lack of hardware using this feature).
* Chip table changed to support the C1010 B0 w/o the U3EN bit work-around
enabled.
* Add the SYM_SETUP_MAX_LUN, SYM_SETUP_LP_PROBE_MAP (used to tell the
driver about chips that are to be claimed with lower priority than old
PCI bus based driver (typically the ncr)), SYM_SETUP_SCSI_DIFF, and
SYM_SETUP_PCI_PARITY options.
Submitted by: Gerard Roudier <groudier@club-internet.fr>
