Specifically, don't allow a value < 1 for any of them (it doesn't make
sense), and don't let the low water mark be greater than the corresponding
high water mark.
Pre-Approved by: wollman
Obtained from: NetBSD
nothing good except of opening a can of (potential or real) security
holes. People maintaining a machine with higher security requirements
need to be on the console anyway, so there's no point in not forcing
them to reboot before starting maintenance.
Agreed by: hackers, guido
This eliminates a lot of #ifdef SMP type code. Things like _curproc reside
in a data page that is unique on each cpu, eliminating the expensive macros
like: #define curproc (SMPcurproc[cpunumber()])
There are some unresolved bootstrap and address space sharing issues at
present, but Steve is waiting on this for other work. There is still some
strictly temporary code present that isn't exactly pretty.
This is part of a larger change that has run into some bumps, this part is
standalone so it should be safe. The temporary code goes away when the
full idle cpu support is finished.
Reviewed by: fsmp, dyson
flag wasn't being respected during vref(), et. al. Note that this
isn't the eventual fix for the locking problem. Fine grained SMP
in the VM and VFS code will require (lots) more work.
cause a problem of spiraling death due to buffer resource limitations.
The vfs_bio code in general had little ability to handle buffer resource
management, and now it does. Also, there are a lot more knobs for tuning the
vfs_bio code now. The knobs came free because of the need that there
always be some immediately available buffers (non-delayed or locked) for
use. Note that the buffer cache code is much less likely to get bogged
down with lots of delayed writes, even more so than before.
It is possible for multiple process to sleep concurrently waiting
for a buffer. When the buffer shortage is a shortage of space but
not a shortage of buffer headers, the processes took turns creating
empty buffers and waking each other to advertise the brelse() of
the empties; progress was never made because tsleep() always found
another high-priority process to run and everything was done at
splbio(), so vfs_update never had a chance to flush delayed writes,
not to mention that i/o never had a chance to complete.
The problem seems to be rare in practice, but it can easily be
reproduced by misusing block devices, at least for sufficently slow
devices on machines with a sufficiently small buffer cache. E.g.,
`tar cvf /dev/fd0 /kernel' on an 8MB system with no disk in fd0
causes the problem quickly; the same command with a disk in fd0
causes the problem not quite as quickly; and people have reported
problems newfs'ing file systems on block devices.
Block devices only cause this problem indirectly. They are pessimized
for time and space, and the space pessimization causes the shortage
(it manifests as internal fragmentation in buffer_map).
This should be fixed in 2.2.
cost since it is only done in cpu_switch(), not for every exception.
The extra state is kept in the pcb, and handled much like the npx state,
with similar deficiencies (the state is not preserved across signal
handlers, and error handling loses state).
shared function.
- use p->p_sleepend to try and get more accurate "time remaining" results
when the time has been adjusted.
- verify writeability of return address so that we can fail before sleeping
if the address for the result is bogus.
Changes to pmap.c for lapic_t lapic && ioapic_t ioapic pointers,
currently equal to apic_base && io_apic_base, will stand alone with the
private page mapping.
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After theISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
This is now the default, it delays most of the MP startup to the function
machdep.c:cpu_startup(). It should be possible to move the 2 functions
found there (mp_start() & mp_announce()) even further down the path once
we know exactly where that should be...
Help from: Peter Wemm <peter@spinner.dialix.com.au>
- The 1st (preparse_mp_table()) counts the number of cpus, busses, etc. and
records the LOCAL and IO APIC addresses.
- The 2nd pass (parse_mp_table()) does the actual parsing of info and recording
into the incore MP table.
This will allow us to defer the 2nd pass untill malloc() & private pages
are available (but thats for another day!).
When a panic occurs early in the SMP boot process 'cpunumber()' hangs,
causing the panic string to be lost. Now the system appears to hang
in 'breakpoint()', but at least the user sees the panic string before the
hang.
switch. I needed 'LINT' to compile for other reasons so I kinda got the
blood on my hands. Note: I don't know how to test this, I don't know if
it works correctly.
panic( "xxxxx\n" );
to:
printf( "xxxxx\n" );
panic( "\n" );
For some as yet undetermined reason the argument to panic() is often NOT
printed, and the system sometimes hangs before reaching the panic printout.
So we hopefully at least print some useful info before the hang, as oppossed to
leaving the user clueless as to what has happened.
and b_validend. The changes to vfs_bio.c are a bit ugly but hopefully
can be tidied up later by a slight redesign.
PR: kern/2573, kern/2754, kern/3046 (possibly)
Reviewed by: dyson
