Refresh upstream driver before impending conversion to iflib.
Major new features:
- Support for Fortville-based 25G adapters
- Support for I2C reads/writes
(To prevent getting or sending corrupt data, you should set
dev.ixl.0.debug.disable_fw_link_management=1 when using I2C
[this will disable link!], then set it to 0 when done. The driver implements
the SIOCGI2C ioctl, so ifconfig -v works for reading I2C data,
but there are read_i2c and write_i2c sysctls under the .debug sysctl tree
[the latter being useful for upper page support in QSFP+]).
- Addition of an iWARP client interface (so the future iWARP driver for
X722 devices can communicate with the base driver).
- Compiling this option in is enabled by default, with "options IXL_IW" in
GENERIC.
Differential Revision: https://reviews.freebsd.org/D9227
Reviewed by: sbruno
MFC after: 2 weeks
Sponsored by: Intel Corporation
Small summary
-------------
o Almost all IPsec releated code was moved into sys/netipsec.
o New kernel modules added: ipsec.ko and tcpmd5.ko. New kernel
option IPSEC_SUPPORT added. It enables support for loading
and unloading of ipsec.ko and tcpmd5.ko kernel modules.
o IPSEC_NAT_T option was removed. Now NAT-T support is enabled by
default. The UDP_ENCAP_ESPINUDP_NON_IKE encapsulation type
support was removed. Added TCP/UDP checksum handling for
inbound packets that were decapsulated by transport mode SAs.
setkey(8) modified to show run-time NAT-T configuration of SA.
o New network pseudo interface if_ipsec(4) added. For now it is
build as part of ipsec.ko module (or with IPSEC kernel).
It implements IPsec virtual tunnels to create route-based VPNs.
o The network stack now invokes IPsec functions using special
methods. The only one header file <netipsec/ipsec_support.h>
should be included to declare all the needed things to work
with IPsec.
o All IPsec protocols handlers (ESP/AH/IPCOMP protosw) were removed.
Now these protocols are handled directly via IPsec methods.
o TCP_SIGNATURE support was reworked to be more close to RFC.
o PF_KEY SADB was reworked:
- now all security associations stored in the single SPI namespace,
and all SAs MUST have unique SPI.
- several hash tables added to speed up lookups in SADB.
- SADB now uses rmlock to protect access, and concurrent threads
can do SA lookups in the same time.
- many PF_KEY message handlers were reworked to reflect changes
in SADB.
- SADB_UPDATE message was extended to support new PF_KEY headers:
SADB_X_EXT_NEW_ADDRESS_SRC and SADB_X_EXT_NEW_ADDRESS_DST. They
can be used by IKE daemon to change SA addresses.
o ipsecrequest and secpolicy structures were cardinally changed to
avoid locking protection for ipsecrequest. Now we support
only limited number (4) of bundled SAs, but they are supported
for both INET and INET6.
o INPCB security policy cache was introduced. Each PCB now caches
used security policies to avoid SP lookup for each packet.
o For inbound security policies added the mode, when the kernel does
check for full history of applied IPsec transforms.
o References counting rules for security policies and security
associations were changed. The proper SA locking added into xform
code.
o xform code was also changed. Now it is possible to unregister xforms.
tdb_xxx structures were changed and renamed to reflect changes in
SADB/SPDB, and changed rules for locking and refcounting.
Reviewed by: gnn, wblock
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9352
and device npx.
This means that FPU is always initialized and handled when available,
and SSE+ register file and exception are handled when available. This
makes the kernel FPU code much easier to maintain by the cost of
slight bloat for CPUs older than 25 years.
CPU_DISABLE_CMPXCHG outlived its usefulness, see the removed comment
explaining the original purpose.
Suggested by and discussed with: bde
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
- Use new option SMP_ON_UP instead of (mis)using specific CPU type.
By this, any SMP kernel can be compiled with SMP_ON_UP support.
- Enable runtime detection of CPU multiprocessor extensions only
if SMP_ON_UP option is used. In other cases (pure SMP or UP),
statically compile only required variant.
- Don't leak multiprocessor instructions to UP kernel.
- Correctly handle data cache write back to point of unification.
DCCMVAU is supported on all armv7 cpus.
- For SMP_ON_UP kernels, detect proper TTB flags on runtime.
Differential Revision: https://reviews.freebsd.org/D9133
Derived from an implementation by Mark Adler.
The fast loop performs three simultaneous CRCs over subsets of the data
before composing them. This takes advantage of certain properties of
the CRC32 implementation in Intel hardware. (The CRC instruction takes 1
cycle but has 2-3 cycles of latency.)
The CRC32 instruction does not manipulate FPU state.
i386 does not have the crc32q instruction, so avoid it there. Otherwise
the implementation is identical to amd64.
Add basic userland tests to verify correctness on a variety of inputs.
PR: 216467
Reported by: Ben RUBSON <ben.rubson at gmail.com>
Reviewed by: kib@, markj@ (earlier version)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9342
* Clang/llvm does not (yet) support -m(no-)spe, so make it gcc-only
* Clang now supports -msoft-float, and does not appear to recognize
"-disable-ppc-float-in-variadic", which appears to have been a crutch until
soft-float was implemented. It's now implemented for both 32- and 64-bit.
* Clang/llvm use a 'medium' code model by default for powerpc64, supporting up
to 4GB TOC, and does not support the '-mminimal-toc' option. Given both of
these, make -mminimal-toc gcc-only.
MFC after: 2 weeks
The intended use is to annotate frequently used globals which either rarely
change (and thus can be grouped in the same cacheline) or are an atomic counter
(which means it may benefit from being the only variable in the cacheline).
Linker script support is provided only for amd64. Architectures without it risk
having other variables put in, i.e. as if they were not annotated. This is
harmless from correctness point of view.
Reviewed by: bde (previous version)
MFC after: 1 month
By default reading the diagnostic counters is disabled. The firmware
decides which counters are supported and only those supported show up
in the dev.mce.X.diagnostics sysctl tree.
To enable reading of diagnostic counters set one or more of the
following sysctls to one:
dev.mce.X.conf.diag_general_enable=1
dev.mce.X.conf.diag_pci_enable=1
MFC after: 1 week
Sponsored by: Mellanox Technologies
Our base binutils sets -many by default anyway, but external gcc may not do
this.
PR: kern/215948
Submitted by: Mark Millard <markmi AT dsl-only DOT net>
Reported by: Mark Millard
MFC after: 2 weeks
There were several places where reference to compression were left
unfinished. Furthermore, KASSERTs contained references to MPPC_INVALID
which is not defined in the tree and therefore were sure to break with
INVARIANTS: comment them out.
Reported by: Eugene Grosbein
PR: 216265
MFC after: 3 days
- Add RATELIMIT kernel configuration keyword which must be set to
enable the new functionality.
- Add support for hardware driven, Receive Side Scaling, RSS aware, rate
limited sendqueues and expose the functionality through the already
established SO_MAX_PACING_RATE setsockopt(). The API support rates in
the range from 1 to 4Gbytes/s which are suitable for regular TCP and
UDP streams. The setsockopt(2) manual page has been updated.
- Add rate limit function callback API to "struct ifnet" which supports
the following operations: if_snd_tag_alloc(), if_snd_tag_modify(),
if_snd_tag_query() and if_snd_tag_free().
- Add support to ifconfig to view, set and clear the IFCAP_TXRTLMT
flag, which tells if a network driver supports rate limiting or not.
- This patch also adds support for rate limiting through VLAN and LAGG
intermediate network devices.
- How rate limiting works:
1) The userspace application calls setsockopt() after accepting or
making a new connection to set the rate which is then stored in the
socket structure in the kernel. Later on when packets are transmitted
a check is made in the transmit path for rate changes. A rate change
implies a non-blocking ifp->if_snd_tag_alloc() call will be made to the
destination network interface, which then sets up a custom sendqueue
with the given rate limitation parameter. A "struct m_snd_tag" pointer is
returned which serves as a "snd_tag" hint in the m_pkthdr for the
subsequently transmitted mbufs.
2) When the network driver sees the "m->m_pkthdr.snd_tag" different
from NULL, it will move the packets into a designated rate limited sendqueue
given by the snd_tag pointer. It is up to the individual drivers how the rate
limited traffic will be rate limited.
3) Route changes are detected by the NIC drivers in the ifp->if_transmit()
routine when the ifnet pointer in the incoming snd_tag mismatches the
one of the network interface. The network adapter frees the mbuf and
returns EAGAIN which causes the ip_output() to release and clear the send
tag. Upon next ip_output() a new "snd_tag" will be tried allocated.
4) When the PCB is detached the custom sendqueue will be released by a
non-blocking ifp->if_snd_tag_free() call to the currently bound network
interface.
Reviewed by: wblock (manpages), adrian, gallatin, scottl (network)
Differential Revision: https://reviews.freebsd.org/D3687
Sponsored by: Mellanox Technologies
MFC after: 3 months
This patch adds driver for temperature/humidity sensor connected via GPIO.
To compile it into kernel add "device gpioths". To activate driver, use
hints (.at and .pins) for gpiobus. As result it will provide temperature &
humidity values via sysctl.
DHT11 is cheap & popular temperature/humidity sensor used via GPIO on ARM
or MIPS devices like Raspberry Pi or Onion Omega.
Reviewed by: adrian
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D9185
in some arm64 hardware, for example the AMD Opteron A1100.
Reviewed by: mav
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8852
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
card presence and write protect switch detection.
A bridge driver just needs to call the setup routine in its attach(), the
teardown in its detach(), and write a couple tiny glue functions to connect
the sdhci interface functions to the new helper functions. This is not
extensively documented, but multiple examples will exist real soon.
Add basic support for A33/R16 that is enough to boot a kernel.
This adds the platform code, padconf data and the new clocks strings.
MFC after: 2 weeks
all public firmwares for all chips since the last release (1.15.37.0)
follows (it's a straight copy-paste from the Release Notes for the
12/30/2016 Unified Wire release on Chelsio's website).
T6 Firmware
++++++++++++
Version : 1.16.26.0
Date : 12/28/2016
Fixes
-----
BASE:
- Max number of egress and control queues adjusted to accomodate
co-processor mode queues.
- Fixed intermittent DDR3/4 ECC errors.
- Fixed a traffic stall when ETS BW is configured as 0%.
- Max number of ethctrl queue in VF set to 1.
ETH:
- Added a new config file option 'speed' under port section to set the
port speed. Use only when auto negotiation is off.
- FEC option removed from firmware config file. cxgbtool can be used to
change the fec setting.
- CPL_TX_TNL_LSO cpl handling added in ETH_TX_PKT_VM handler. This fixes
large tunnel tcp packet support for VxLAN.
Version : 1.16.22.0
Date : 12/05/2016
Fixes
-----
BASE:
- fw_port_type updated in fw API to match kernel.org definitions.
- Saved power by disaling unused MAC lanes.
- Configures correct power bin.
- Enhanced DDR4 performance.
- Enabled interrupts.
- Fixed an issue where filter rule for 'unicast hash' is not working.
ETH:
- Disabled auto negotiation by default because most of 100G switches do
not support AN as of today.
- Fixed flow control not getting disabled problem.
- Fixed an issue where port0 doesn't come up sometimes.
- Fixed 10G link not coming up issue.
- Fixed an issue with promiscuous mode when dcbx disabled.
OFLD:
- Fixed a connection stuck issue when abort is received during out of tx
pages backpressure.
ENHANCEMENTS
------------
BASE:
- Added inline TLS mode support.
Version : 1.16.12.0
Date : 11/11/2016
ENHANCEMENTS
------------
BASE:
- Added T6 support.
- Added T6 1G/10G/25G/40G/100G link speeds.
- Added T6 co-processor mode crypto support.
- Added facility to increase link AN+AEC timeout.
OFLD:
- Added support for all T5 offload protocols except FCoE.
iSCSI:
- iscsi completion moderation enabled.
=======================================================================
T5 Firmware
++++++++++++
Version : 1.16.26.0
Date : 12/28/2016
FIXES
-----
BASE:
- Max number of ethctrl queue in VF set to 1.
Version : 1.16.22.0
Date : 12/05/2016
FIXES
-----
BASE:
- Fixed an issue where filter rule for 'unicast hash' is not working.
ETH:
- Fixed an issue with promiscuous mode when dcbx disabled.
ENHANCEMENTS
------------
ETH:
- Added 40G-KR support.
Version : 1.16.12.0
Date : 11/11/2016
FIXES
-----
BASE:
- Fixed multiple issues related with VFs FLR processing.
- Fixed channel assignment based on number of ports in adapter.
- Fixed a crash when VM having PF assigned as passthrough mode is
rebooted.
- Handled 2nd HELLO command from the same PF without seeing BYE from the
same PF and if that is the only PF.
- A warning is printed in firmware log if PCI-E cookie generation is
enabled in serial initialization file.
- Fixed multiple issues related with Filtering.
- Enabled DSGL memory write for iscsi and rdma.
- Added new FW_PARAMS_CMD[DEV] options to retrieve Serial Configuration
and VPD version numbers.
- Fixed an issue where LVDS output was not getting enabled using vpd.
DCBX:
- Fixed DCBX CEE Incorrect class to pririty mapping.
- Fixed incorrect interpretation of DCBX IEEE PFC.
ETH:
- Adjusted the link related delay timings according to the QSFP spec.
- Improved 40G link bringup time with few switches.
OFLD:
- Do not reserve qp/cq if rdma capability is not enabled.
- Fixed an issue where approx 1600+ TOE connections were causing a
firmware fatal error.
FOiSCSI:
- Fixed an issue where unloading foiscsi driver causes mailbox timeout.
ENHANCEMENTS
------------
BASE:
- Added 10G KR/KX support.
- Added T540-BT adapter support.
- Added 4 new rss key modes for PFs and VFs.
OFLD:
- Added new WR FW_RI_FR_NSMR_TPTE_WR to improve fast MR write
performance in RDMA.
Version : 1.16.5.0
Date : 10/26/2016
FIXES
-----
BASE:
- Fixed multiple issues where FLR from multiple VFs can cause firmware
crash.
- Fixed channel assignment based on number of ports in adapter.
- Fixed the HELLO command master force api to handle the 2nd HELLO
correctly without getting BYE from the PF driver.
- Added facility to retrieve Serial configuration and VPD version. Two
new FW_PARAMS_CMD[DEV] options added to retrieve these values.
- Fixed multiple issues where FLR from multiple VFs are not completing.
- Added new RSS hash secret key modes.
- Fixed an issue where LVDS output was not getting enabled using vpd.
DCBX:
- Fixed an issue where iscsi tlv is sent incorrectly to host (DCBX CEE).
- Fixed an issue where app priority values are not handled correctly
in fw (DCBX IEEE).
ETH:
- Adjusts the link related delay timings according to the QSFP spec.
- Changed 2.5G mac speed bit to 25G mac speed bit in fw API.
- Improvement in 40G link bringup time with few switches.
OFLD:
- Do not reserve qp/cq if rdma capability is not enabled.
- Fixed an issue where approx 1600+ TOE connections were causing a
firmware fatal error.
- Fixed DSGL memory write in T5. Now iwarp and iscsi can use DSGL to do
memory write.
- Fixed multiple issues in hash filter mode where incorrect protocol
mask was getting used and affecting hash filter functionality.
- New fastpath WR FW_RI_FR_NSMR_TPTE_WR (with fully populated TPTE) is
added for small REG_MR operations.
FOiSCSI:
- Fixed an issue in foiscsi recovery path.
- Fixed an issue where foiscsi (in VM in PCIE passthrough mode) didn't
come up after VM FLR.
ENHANCEMENTS
------------
ETH:
- Implemented 1G/10G KR/KX ability.
- Implemented T540-BT adapter support.
=======================================================================
T4 Firmware
+++++++++++
Version : 1.16.12.0
Date : 11/11/2016
FIXES
-----
BASE:
- Fixed an issue where reading temperature sesors using ldst command
causes mailbox timeout.
- Added new FW_PARAMS_CMD[DEV] options to retrieve Serial Configuration
and VPD version numbers.
ETH:
- Fixed DCBX CEE Incorrect class to pririty mapping.
FOiSCSI:
- Fixed an issue where unloading foiscsi driver causes mailbox timeout.
MFC after: 3 days
Sponsored by: Chelsio Communications
Wake-on-lan is not supported in production on any of our adapters, as
they don't have the required AUX power connector. (It's possible that
AUX power is supplied to some of our ALOM or mezz adapters, but if so
then we've never implemented or tested WoL support.)
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8972
Recognize new MACHINE_ARCH names now as we have added hardfloat support.
Switch JZ4780 to mipselhf and remove all uses of TARGET_ARCH in kernel
.mk files.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8989
Add SPI mode (PIO-only) support for Intel Synchronous Serial Port that
can be found in several Intel's products starting from PXA family.
Most of implementations have slight differences in behavior and in
addresses for registers subset. This driver covers only BayTrail SoC
implementation for it's the only hardware I have to test it on.
Driver attaches to ACPI bus only and does not have PCI or FDT support
for now due to lack of hardware to test it on.
"intelspi" is the best name I've managed to come up with. Linux driver
name (spi-pxa2xx) does not make sense because current implementation
does not support actual PXA2xx SoCs. And as far as I know there is no
codename assigned to Intel SSP chip.
Reviewed by: br, manu
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D8896
Add ACPI part for ig4 driver to make it work on Intel BayTrail SoC where
ig4 device is available only through ACPI
Reviewed by: avg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8742
to recreate it from ${MAKEOBJDIRPREFIX} and ${SRC_BASE} and ${KERNCONF},
the latter being especially problematic when KERNCONF is set to the names
of multiple kernel configs.
FC-Tape provides additional link level error recovery, and is
highly recommended for tape devices. It will only be turned on for
a given target if the target supports it.
Without this setting, we default to whatever FC-Tape setting is in
NVRAM on the card.
This can be overridden by setting the following loader tunable, for
example for isp0:
hint.isp.0.nofctape=1
sys/conf/options:
Add a new kernel config option, ISP_FCTAPE_OFF, that
defaults the FC-Tape configuration to off.
sys/dev/isp/isp_pci.c:
If ISP_FCTAPE_OFF is defined, turn off FC-Tape. Otherwise,
turn it on if the card supports it.
share/man/man4/isp.4:
Add a description of FC-Tape to the isp(4) man page.
Add descriptions of the fctape and nofctape options, as well as the
ISP_FCTAPE_OFF kernel configuration option.
Add the ispfw module and kernel drivers to the suggested
configurations at the top of the man page so that users are less
likely to leave it out. The driver works well with the included
firmware, but may not work at all with whatever firmware the user
has flashed on their card.
MFC after: 3 days
Sponsored by: Spectra Logic
