For now, the only module implement is 'sample', and that's only partially
implemented. The main issue here with reusing this structure in userland
is that it uses 'rix' everywhere, which requires the userland code to
have access to the current HAL rate table.
For now, this is a very large work in progress.
Specific details:
* The rate control information is per-node at the moment and wrapped
in a TLV, to ease parsing and backwards compatibility.
* .. but so I can be slack for now, the userland statistics are just
a copy of the kernel-land sample node state.
* However, for now use a temporary copy and change the rix entries
to dot11rate entries to make it slightly easier to eyeball.
Problems:
* The actual rate information table is unfortunately indexed by rix
and it doesn't contain a rate code. So the userland side of this
currently has no way to extract out a mapping.
TODO:
* Add a TLV payload to dump out the rate control table mapping so
'rix' can be turned into a dot11 / MCS rate.
* .. then remove the temporary copy.
makelist:
change tr '[a-z]' '[A-Z]' to tr '[:lower:]' '[:upper:]' so that POSIX
systems work proerly regardsless of environment variable settings.
tokenizer.c:
pass lint on _LP64
Obtained from: NetBSD
MFC after: 2 weeks
amd64. It is implemented as __pure2 inline with non-volatile asm read
from pcpu, which allows a compiler to cache its results.
Convert most PCPU_GET(pcb) and curthread->td_pcb accesses into curpcb.
Note that __curthread() uses magic value 0 as an offsetof(struct pcpu,
pc_curthread). It seems to be done this way due to machine/pcpu.h
needs to be processed before sys/pcpu.h, because machine/pcpu.h
contributes machine-depended fields to the struct pcpu definition. As
result, machine/pcpu.h cannot use struct pcpu yet.
The __curpcb() also uses a magic constant instead of offsetof(struct
pcpu, pc_curpcb) for the same reason. The constants are now defined as
symbols and CTASSERTs are added to ensure that future KBI changes do
not break the code.
Requested and reviewed by: bde
MFC after: 3 weeks
data introduced in r236061. Using that flag doesn't make that much
sense on this case as the DMA maps using it are also created during
sym_pci_attach(). Moreover, due to the maxsegsz parameter used, doing
so may exhaust the bounce pages pool on architectures requiring
bounce pages. [1]
While at it, use a slightly more appropriate maxsegsz parameter.
PR: 169526
Submitted by: Mike Watters [1]
MFC after: 3 days
ELF parser. Specifically, do not allow note reader and interpreter
path comparision in the brandelf code to read past end of the page.
This may happen if specially crafter ELF image is activated.
Submitted by: Lukasz Wojcik <lukasz.wojcik zoho com>
MFC after: 3 days
TX descriptor link pointers.
This is required for the AR93xx and later chipsets.
The RX path is slightly different - the legacy RX path directly
accesses ath_desc->ds_link for now, however this isn't at all done
for EDMA (FIFO) RX.
Now, for those performing a little software archeology here:
This is all a bit sub-optimal. "struct ath_desc" is only really relevant
for the pre-AR93xx NICs - where ds_link and ds_data is always in the
same location.
The AR93xx and later NICs have different descriptor layouts altogether.
Now, for AR93xx and later NICs, you should never directly reference
ds_link and ds_data, as:
* the RX descriptors don't have either - the data is _after_ the RX
descriptor. They're just one large buffer. There's also no need for
a per-descriptor RX buffer size as they're all fixed sizes.
* the TX descriptors have 4 buffer and 4 length fields _and_ a link
pointer. Each frame takes up one TX FIFO pointer, but it can contain
multiple subframes (either multiple frames in a buffer, and/or
multiple frames in an aggregate/RIFS burst.)
* .. so, when TX frames are queued to a hardware queue, the link
pointer is ONLY for buffers in that frame/aggregate. The next frame
starts in a new FIFO pointer.
* Finally, descriptor completion status is in a different ring.
I'll write something up about that when its time to do so.
This was inspired by Linux ath9k and the reference driver but is a
reimplementation.
Obtained from: Linux ath9k, Qualcomm Atheros
The DMA FIFO chips (AR93xx and later) differ slightly to th elegacy
chips:
* The RX DMA descriptors don't have a ds_link field;
* The TX DMA descriptors have a ds_link field however at a different
offset.
This is a reimplementation based on what the reference driver and ath9k
does.
A subsequent commit will enable it in the TX and beacon paths.
Obtained from: Linux ath9k, Qualcomm Atheros
occurs using the SSE math processor. Update comments describing the
handling of the exception status bits in coprocessors control words.
Remove GET_FPU_CW and GET_FPU_SW macros which were used only once.
Prefer to use curpcb to access pcb_save over the longer path of
referencing pcb through the thread structure.
Based on the submission by: Ed Alley <wea llnl gov>
PR: amd64/169927
Reviewed by: bde
MFC after: 3 weeks
Merge changes from illumos
906 dtrace depends_on pragma should search all library paths, not just the
current one
949 dtrace should only include the first instance of a library found on
its library path
Illumos Revisions: 13353:936a1e45726c
13354:2b2c36a81512
Reference:
https://www.illumos.org/issues/906https://www.illumos.org/issues/949
Tested by: Fabian Keil
Obtained from: Illumos
MFC after: 3 weeks
arraysz could get initialized to zero on ZFS because ZFS reports
directory sizes differently compared to UFS.
PR: bin/169493
Tested by: swills
MFC after: 2 weeks
