respectively logging and dropping ICMP REDIRECT packets.
Note that there is no rate limiting on the log messages, so log_redirect
should be used with caution (preferrably only for debugging purposes).
Prompted by docs/12343, in which people seemed to get a little confused.
The original text in the file said:
[...]
# By default we use COM1 as our serial console port *if* we're going to use
# a serial port as our console at all. (0x3E8 = COM2)
#
#BOOT_COMCONSOLE_PORT= 0x3F8
[...]
From what I can make out, some people have assumed that means that if
they just uncomment the BOOT_COMCONSOLE_PORT then it will use COM2:
These same people then assume that "0x3F8" on that line is a typo for
"0x3E8".
What it actually means is that if you uncomment the line then the default
stays as "Ox3F8" (COM1:), and that you have to uncomment the line, *and*
change the value of the variable in order to use COM2:.
So I've made that a little bit clearer. I've also listed the hex values
for COM1: thru COM4:, snarfed from sys/isa/isareg.h.
PR: docs/12343
Submitted by: Bill Grunfelder <wjgrun@dippy.cyberwar.com>
Originally submitted by: Wayne Self <wself@cdrom.com>
Allow a ppp startup option in rc.conf.
Adjust sysinstall so that it appends to the end of ppp.conf
and uses the generated profile to start ppp in auto mode on
boot.
Submitted by: Josef L. Karthauser <joe@uk.FreeBSD.org>
get a list of interfaces, and then automatically configure them if
${ifconfig_${ifn}} or /etc/start_if.${ifn} exists.
This makes it a lot easier to deal with machines that constantly change
their network configuration as you can leave ifconfig settings for all
the possible cards - just the ones that are present will be configured.
and set it to "/etc/pccard.conf.sample" in /etc/defaults/rc.conf.
Perhaps this default value can be inappropriate,
but I set to this value for the convenience of PC-card boot.flp users.
Please correct it if there are better solutions.
twice to enable wrapping for internal wrapping as well. If the option is
not specified wrapping is turned off so that inetd will behave exactly
as it used to before TCP Wrappers was imported.
Change etc/defaults/rc.conf so as to encourage wrapping on new systems.
Clarify the use of TCP Wrappers in the IMPLEMENTATION NOTES of the
manual page.
Approved by: jkh
default.
Despite their name it doesn't keep TCP sessions alive, it kills
them if the other end has gone AWOL. This happens a lot with
clients which use NAT, dynamic IP assignment or which has a 2^32
* 10^-3 seconds upper bound on their uptime.
There is no detectable increase in network trafic because of this:
two minimal TCP packets every two hours for a live TCP connection.
Many servers already enable keepalives themselves.
The host requirements RFC is 10 years old, and doesn't know about
the loosing clients of todays InterNet.
adapter (and some workalikes). Also add man pages and a wicontrol
utility to manipulate some of the card parameters.
This driver was written using information gleaned from the Lucent HCF Light
library, though it does not use any of the HCF Light code itself, mainly
because it's contaminated by the GPL (but also because it's pretty gross).
The HCF Light lacks certain featurs from the full (but proprietary) HCF
library, including 802.11 frame encapsulation support, however it has
just enough register information about the Hermes chip to allow someone
with enough spare time and energy to implement a proper driver. (I would
have prefered getting my hands on the Hermes manual, but that's proprietary
too. For those who are wondering, the Linux driver uses the proprietary
HCF library, but it's provided in object code form only.)
Note that I do not have access to a WavePOINT access point, so I have
only been able to test ad-hoc mode. The wicontrol utility can turn on
BSS mode, but I don't know for certain that the NIC will associate with
an access point correctly. Testers are encouraged to send their results
to me so that I can find out if I screwed up or not.
automagically find all the partitions. This is to be preferred to the
somewhat emetic usage of vinum_slices and the equally obnoxious 'vinum
read' command.
log_in_vain:
log_in_vain turns on logging for packets to ports for which
there is no listener.
rc.sysctl:
A generic way to set sysctl values. It reads /etc/syslog.conf
and sets values based on that. No /etc/syslog.conf has been
checked in yet, and I've not added this to the makefile yet
until I get more feedback.
Reviewed by: -current, -hackers and bde especially
enable_quotas - use quotas on your system
check_quotas - check for violations on startup
By assuming that a system was neat and without violation before it booted
we can skip a long (and at that point needless) process.
Submitted by: Alex Perel <veers@disturbed.net>
