bug where a PCI device would be powered down if it failed to probe, but
not when its driver was detached (e.g. via kldunload).
- Add a new helper method resource_list_release_active() which forcefully
releases any active resources of a specified type from a resource list.
- Add a bus_child_detached method for the PCI bus driver which forces any
active resources to be released (and whines to the console if it finds
any) and then powers the device down.
- Call pci_child_detached() if we fail to probe a device when a driver
is kldloaded. This isn't perfect but can avoid leaking resources
from a probe() routine in the kldload case.
Reviewed by: imp, brooks
MFC after: 1 month
a new firmware command.
NVMe controllers may support up to 7 firmware slots for storing of
different firmware revisions. This new firmware command supports
firmware replacement (i.e. firmware download) with or without immediate
activation, or activation of a previously stored firmware image. It
also supports selection of the firmware slot during replacement
operations, using IDENTIFY information from the controller to
check that the specified slot is valid.
Newly activated firmware does not take effect until the new controller
reset, either via a reboot or separate 'nvmecontrol reset' command to the
same controller.
Submitted by: Joe Golio <joseph.golio@emc.com>
Obtained from: EMC / Isilon Storage Division
MFC after: 3 days
max transfer size. This guards against rogue commands coming in from
userspace.
Also add KASSERTS for the virtual address and unmapped bio cases, if the
transfer size exceeds the controller's max transfer size.
Sponsored by: Intel
MFC after: 3 days
Also allow admin commands to transfer up to this maximum I/O size, rather
than the artificial limit previously imposed. The larger I/O size is very
beneficial for upcoming firmware download support. This has the added
benefit of simplifying the code since both admin and I/O commands now use
the same maximum I/O size.
Sponsored by: Intel
MFC after: 3 days
by treating it as UDMA.
This fixes a problem introduced in r249933/r249939, where CAM sends
ATA_DSM_TRIM to SATA devices using ATA_PASSTHROUGH_16. scsi_ata_trim()
sets protocol as DMA (not UDMA) which is for multi-word DMA, even
though no such mode is selected for the device. isci(4) would fail
these commands which is the correct behavior but not consistent with
other HBAs, namely LSI's.
smh@ did some further testing on an LSI controller, which rejected
ATA_PASSTHROUGH_16 commands with mode=UDMA_OUT, even though only
a UDMA mode was selected on the device. So this precludes adding
any kind of mode detection in CAM to determine which mode to use on
a per-device basis.
Sponsored by: Intel
Discussed with: scottl, smh
Reported by: scottl
Tested by: scottl
MFC after: 3 days
support cache flush and write barrier commands.
sys/dev/xen/blkfront/block.h:
Add per-command flag that specifies that the I/O queue must
be frozen after this command is dispatched. This is used
to implement "single-stepping".
Remove the unused per-command flag that indicates a polled
command.
Add block device instance flags to record backend features.
Add a block device instance flag to indicate the I/O queue
is frozen until all outstanding I/O completes.
Enhance the queue API to allow the number of elements in a
queue to be interrogated.
Prefer "inline" to "__inline".
sys/dev/xen/blkfront/blkfront.c:
Formalize queue freeze semantics by adding methods for both
global and command-associated queue freezing.
Provide mechanism to freeze the I/O queue until all outstanding
I/O completes. Use this to implement barrier semantics
(BIO_ORDERED) when the backend does not support
BLKIF_OP_WRITE_BARRIER commands.
Implement BIO_FLUSH as either a BLKIF_OP_FLUSH_DISKCACHE
command or a 0 byte write barrier. Currently, all publicly
available backends perform a diskcache flush when processing
barrier commands, and this frontend behavior matches what
is done in Linux.
Simplify code by using new queue length API.
Report backend features during device attach and via sysctl.
Submitted by: Roger Pau Monné
Submitted by: gibbs (Merge with new driver queue API, sysctl support)
The AHB code:
* hard coded the AR9130 device id;
* assumes a 4k flash calibration space.
This code now extends this:
* hint.ath.X.eepromsize now overrides the eeprom range, instead of 4k
* hint.ath.X.device_id and hint.ath.X.vendor_id can now be overridden.
Tested:
* AR9330 board (Carambola 2)
one. This change also fixes non-working traffic LED on BCM57780.
Submitted by: Masanobu SAITOH <msaitoh@NetBSD.org>
Tested by: Alexander Milanov <a@amilanov.com>
There are some systems reported, where PCI BAR(5), used for SATA registers
access, is present, but not functional. Attempt to use it brakes devices
detection logic. Try to detect those cases on attach by setting and testing
some bits in SControl register. If bits are unsettable, fallback to legacy
ATA without hot-plug detection, speed control/reporting, etc.
MFC after: 2 weeks
tester of this fix, and realloc_bars breaks some other cases as a small
BAR that is reallocated can end up grabbing space needed by a much larger
BAR in the existing window of a PCI-PCI bridge.
MFC after: 3 days
checksum header. The header contains a received frame length but
the defined length for AX88772B is different with other ASIX
controllers. When the RX checksum is off, AX88772B controller does
not prepend a checksum header so driver has to use normal header
length mask.
This change should fix RX errors when RX checksum offloading is
off.
Tested by: kevlo
MFC After: 1 week
(which should be a PCIE Gen 3 slot for this adapter) by looking back thru the PCI
parent devices to the slot device.
The fix above also corrects the bandwidth display to GT/s rather than the
incorrect Gb/s
Next, allow the use of ALTQ if you select the compile option IXGBE_LEGACY_TX.
Allow the use of 'unsupported' optic modules by a compile option as well.
Add a phy reset capability into the stop code, this is so a static configured
driver will still behave properly when taken down (not being able to unload it).
This revision synchronizes the shared code with Intel internal current code,
and note that it now includes DCB supporting code, this was necessitated by
some internal changes with the code, but it also will provide the opportunity
to develop this feature in the core driver down the road.
I have edited the README to get rid of some of the worse anachronisms in it
as well, its by no means as robust as I might wish at this point however.
Oh, I also have included some conditional stuff in the code so it will be
compatible in both the 9.X and 10 environments.
Performance has been a focus in recent changes and I believe this revision
driver will perform very well in most workloads.
MFC after: 2 weeks
stops updating the vertical retrace indicator. The text mouse
renderer in syscons is executing from the callout and spins waiting
for the start of next frame. As result, after the X server finishes,
since the VGA cannot be turned on, but syscons does not know about
this, the clock swi spins forever.
Hack around the problem by disabling wait for the retrace if KMS is
activated.
Diagnosed and tested by: Michiel Boland <boland37@xs4all.nl>
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
thread might fault on the same GTT offset meantime and instantiate the
mapping. Recheck that the mgt device object still does not have a
page at the current offset after relocking, and return a possibly
installed page.
Reported by: Oleg Sidorkin <osidorkin@gmail.com>
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
only re-enable I/O when all reasons have cleared.
sys/dev/xen/blkfront/block.h:
In the block front driver softc, replace the boolean
XBDF_FROZEN flag with a count of commands and driver global
issues that freeze the I/O queue. So long xbd_qfrozen_cnt
is non-zero, I/O is halted.
Add flags to xbd_flags for tracking grant table entry and
free command resource shortages. Each of these classes can
increment xbd_qfrozen_cnt at most once.
Add a command flag (XBDCF_ASYNC_MAPPING) that is set whenever
the initial mapping attempt of a command fails with EINPROGRESS.
sys/dev/xen/blkfront/blkfront.c:
In xbd_queue_cb(), use new XBDCF_ASYNC_MAPPING flag to definitively
know if an async bus dmamap load has occurred.
Add xbd_freeze() and xbd_thaw() helper methods for managing
xbd_qfrozen_cnt and use them to implement all queue freezing logic.
Add missing "thaw" to restart I/O processing once grant references
become available.
Sponsored by: Spectra Logic Corporation
QEMU 1.4 made the descriptor requirement stricter - the size of buffer
descriptor must exactly match the number of MAC addresses provided.
PR: kern/178955
MFC after: 5 days
scheme for defining inline command queuing functions.
Prefer enums to #defines.
sys/dev/xen/blkfront/block.h
Replace inline function generation performed by the
XBDQ_COMMAND_QUEUE() macro with single instances of each
inline function (init, enqueue, dequeue, remove). This was
made possible by using queue indexes instead of bit flags
in the command structure, and passing the index enum as
an argument to the functions.
Improve panic/assert messages in the queue functions.
Combine queue data and stats into a single data structure
and declare an array of them instead of each queue individually.
Convert command flags, softc state, and softc flags to enums.
sys/dev/xen/blkfront/blkfront.c
Mechanical adjustments for new queue api.
Sponsored by: Spectra Logic Corporation
MFC after: 1 week
This hasn't yet been tested as unfortunately the AR3012 I have doesn't
have the "real" firmware on it; it shipped with the cut down HCI firmware
that only understands enough to accept a new firmware image.
* Linux ath9k (GPIO constants)
generic mii_phy_reset().
- Return the result of mii_mediachg() rather than blindly returning 0.
- on smsc(4), driver lock should be held to get current
mii_media_active/mii_media_status value.
Reviewed by: yongari
* Add the LNA configuration table entries for AR933x/AR9485
* Add a chip-dependent LNA signal level delta in the startup path
* Add a TODO list for the stuff I haven't yet ported over but
I haven't.
Tested:
* AR9462 with LNA diversity enabled
In netif_free(), call ifmedia_removeall() after ether_ifdetach()
so that bpf listeners are detached, any link state processing
is completed, and there is no chance for external reference to media
information.
Suggested by: yongari
MFC after: 1 week
exact same (subsystem) device and vendor IDs. However, the reference
design for the OXu16PCI954 uses a 14.7456 MHz clock (as does the EXSYS
EX-41098-2 equipped with these), while at least the OX16PCI954 defaults
to a 1.8432 MHz one. According to the datasheets of these chips, the
only difference in PCI configuration space is that OXu16PCI954 have
a revision ID of 1 while the other two are at 0. So employ the latter
for determining the default clock rates of this family.
Note that one might think that the actual clock could be derived from
the Clock Prescaler Register (CPR) of these chips. Unfortunately, this
is not that case and its use and content are orthogonal to the frequency
of the crystal employed.
Tested with an EXSYS EX-41098-2, which identifies and attaches as:
pcib4@pci0:19:0:0: class=0x060400 card=0x02dd1014 chip=0x10801b21
rev=0x03 hdr=0x01
vendor = 'ASMedia Technology Inc.'
device = 'ASM1083/1085 PCIe to PCI Bridge'
class = bridge
subclass = PCI-PCI
puc0@pci0:20:4:0: class=0x070006 card=0x00001415 chip=0x95011415
rev=0x01 hdr=0x00
vendor = 'Oxford Semiconductor Ltd'
device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)'
class = simple comms
subclass = UART
puc1@pci0:20:4:1: class=0x068000 card=0x00001415 chip=0x95111415
rev=0x01 hdr=0x00
vendor = 'Oxford Semiconductor Ltd'
device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)'
class = bridge
puc2@pci0:20:8:0: class=0x070006 card=0x00001415 chip=0x95011415
rev=0x01 hdr=0x00
vendor = 'Oxford Semiconductor Ltd'
device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)'
class = simple comms
subclass = UART
puc3@pci0:20:8:1: class=0x068000 card=0x00001415 chip=0x95111415
rev=0x01 hdr=0x00
vendor = 'Oxford Semiconductor Ltd'
device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)'
class = bridge
pci20: <ACPI PCI bus> on pcib4
puc0: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5000-0x501f,
0x5020-0x503f mem 0xc6000000-0xc6000fff,0xc6001000-0xc6001fff irq 16 at
device 4.0 on pci20
uart1: <16950 or compatible> at port 1 on puc0
uart2: <16950 or compatible> at port 2 on puc0
uart3: <16950 or compatible> at port 3 on puc0
uart4: <16950 or compatible> at port 4 on puc0
puc1: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port
0x5040-0x505f,0x5060-0x507f mem 0xc6002000-0xc6002fff,0xc6003000-0xc6003fff
irq 16 at device 4.1 on pci20
puc2: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5080-0x509f,
0x50a0-0x50bf mem 0xc6004000-0xc6004fff,0xc6005000-0xc6005fff irq 16 at
device 8.0 on pci20
uart5: <16950 or compatible> at port 1 on puc2
uart6: <16950 or compatible> at port 2 on puc2
uart7: <16950 or compatible> at port 3 on puc2
uart8: <16950 or compatible> at port 4 on puc2
puc3: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port
0x50c0-0x50df,0x50e0-0x50ff mem 0xc6006000-0xc6006fff,0xc6007000-0xc6007fff
irq 16 at device 8.1 on pci20
MFC after: 2 weeks
Only four specific ATA PIO commands transfer several sectors per DRQ block
(interrupt). All other ATA PIO commands transfer one sector or 512 bytes
at one time. Hardcode these exceptions in mvs(4) with ATA_CAM option.
This fixes timeout of READ LOG EXT command used by `smartctl -x /dev/adaX`.
Also it fixes timeout of DOWNLOAD_MICROCODE on `camcontrol fwdownload`.
The reference HAL pushes a config group parameter to the driver layer
to inform it which particular chip behaviour to implement.
This particular value tags it as an AR9285.
The AR9485 chip and AR933x SoC both implement LNA diversity.
There are a few extra things that need to happen before this can be
flipped on for those chips (mostly to do with setting up the different
bias values and LNA1/LNA2 RSSI differences) but the first stage is
putting this code into the driver layer so it can be reused.
This has the added benefit of making it easier to expose configuration
options and diagnostic information via the ioctl API. That's not yet
being done but it sure would be nice to do so.
Tested:
* AR9285, with LNA diversity enabled
* AR9285, with LNA diversity disabled in EEPROM
d_getattr(). Since these drivers use disk(9) KPI and not directly GEOM, use
of that function means KPI layering violation, causing extra g_io_deliver()
call for the request.
