The NVME standard has required in section 7.2.6, since at least 1.1,
that a clean shutdown is signalled by deleting the subission and the
completion queues before setting the shutdown bit in CC. The 1.0
standard, apparently, did not and many of the early Intel cards didn't
care. Some newer cards care, at least one whose beta firmware can
scramble the card on an unclean shutdown. Linux has done this for some
time. To make it possible to move forward with an evaluation of this
pre-release card with wonky firmware, delete the queues on the card
when we delete the qpair structures.
Sponsored by: Netflix
We'll need to delete namespaces soon, so go ahead and stop making
these devices eternal. It doesn't help much, and will be getting in
the way soon.
Sponsored by: Netflix
During shutdown mps waits for its SSU requests to complete however when
performing a reboot after handling a panic the scheduler is stopped so
getmicrotime which is used can be non-functional.
Switch to using the same method as shutdown_panic to ensure we actually
complete.
In addition reduce the timeout when RB_NOSYNC is set in howto as we expect
this to fail.
Reviewed by: slm
MFC after: 1 week
Sponsored by: Multiplay
Differential Revision: https://reviews.freebsd.org/D12776
Compare sbavail() with the cached sb_off of already-sent data instead of
always comparing with zero. This will correctly close the connection and
send the FIN if the socket buffer contains some previously-sent data but
no unsent data.
Reported by: Harsh Jain @ Chelsio
Sponsored by: Chelsio Communications
- Remove the one use of is_tls_offload() and the function. AIO special
handling only needs to be disabled when a TOE socket is actively doing
TLS offload on transmit. The TOE socket's mode (which affects receive
operation) doesn't matter, so remove the check for the socket's mode and
only check if a TOE socket has TLS transmit keys configured to determine
if an AIO write request should fall back to the normal socket handling
instead of the TOE fast path.
- Move can_tls_offload() into t4_tls.c. It is not used in critical paths,
so inlining isn't that important. Change return type to bool while here.
Sponsored by: Chelsio Communications
When multiple trims are in the queue, collapse them as much as
possible. At present, this usually results in only a few trims being
collapsed together, but more work on that will make it possible to do
hundreds (up to some configurable max).
Sponsored by: Netflix
The TOE engine in Chelsio T6 adapters supports offloading of TLS
encryption and TCP segmentation for offloaded connections. Sockets
using TLS are required to use a set of custom socket options to upload
RX and TX keys to the NIC and to enable RX processing. Currently
these socket options are implemented as TCP options in the vendor
specific range. A patched OpenSSL library will be made available in a
port / package for use with the TLS TOE support.
TOE sockets can either offload both transmit and reception of TLS
records or just transmit. TLS offload (both RX and TX) is enabled by
setting the dev.t6nex.<x>.tls sysctl to 1 and requires TOE to be
enabled on the relevant interface. Transmit offload can be used on
any "normal" or TLS TOE socket by using the custom socket option to
program a transmit key. This permits most TOE sockets to
transparently offload TLS when applications use a patched SSL library
(e.g. using LD_LIBRARY_PATH to request use of a patched OpenSSL
library). Receive offload can only be used with TOE sockets using the
TLS mode. The dev.t6nex.0.toe.tls_rx_ports sysctl can be set to a
list of TCP port numbers. Any connection with either a local or
remote port number in that list will be created as a TLS socket rather
than a plain TOE socket. Note that although this sysctl accepts an
arbitrary list of port numbers, the sysctl(8) tool is only able to set
sysctl nodes to a single value. A TLS socket will hang without
receiving data if used by an application that is not using a patched
SSL library. Thus, the tls_rx_ports node should be used with care.
For a server mostly concerned with offloading TLS transmit, this node
is not needed as plain TOE sockets will fall back to software crypto
when using an unpatched SSL library.
New per-interface statistics nodes are added giving counts of TLS
packets and payload bytes (payload bytes do not include TLS headers or
authentication tags/MACs) offloaded via the TOE engine, e.g.:
dev.cc.0.stats.rx_tls_octets: 149
dev.cc.0.stats.rx_tls_records: 13
dev.cc.0.stats.tx_tls_octets: 26501823
dev.cc.0.stats.tx_tls_records: 1620
TLS transmit work requests are constructed by a new variant of
t4_push_frames() called t4_push_tls_records() in tom/t4_tls.c.
TLS transmit work requests require a buffer containing IVs. If the
IVs are too large to fit into the work request, a separate buffer is
allocated when constructing a work request. This buffer is associated
with the transmit descriptor and freed when the descriptor is ACKed by
the adapter.
Received TLS frames use two new CPL messages. The first message is a
CPL_TLS_DATA containing the decryped payload of a single TLS record.
The handler places the mbuf containing the received payload on an
mbufq in the TOE pcb. The second message is a CPL_RX_TLS_CMP message
which includes a copy of the TLS header and indicates if there were
any errors. The handler for this message places the TLS header into
the socket buffer followed by the saved mbuf with the payload data.
Both of these handlers are contained in tom/t4_tls.c.
A few routines were exposed from t4_cpl_io.c for use by t4_tls.c
including send_rx_credits(), a new send_rx_modulate(), and
t4_close_conn().
TLS keys for both transmit and receive are stored in onboard memory
in the NIC in the "TLS keys" memory region.
In some cases a TLS socket can hang with pending data available in the
NIC that is not delivered to the host. As a workaround, TLS sockets
are more aggressive about sending CPL_RX_DATA_ACK messages anytime that
any data is read from a TLS socket. In addition, a fallback timer will
periodically send CPL_RX_DATA_ACK messages to the NIC for connections
that are still in the handshake phase. Once the connection has
finished the handshake and programmed RX keys via the socket option,
the timer is stopped.
A new function select_ulp_mode() is used to determine what sub-mode a
given TOE socket should use (plain TOE, DDP, or TLS). The existing
set_tcpddp_ulp_mode() function has been renamed to set_ulp_mode() and
handles initialization of TLS-specific state when necessary in
addition to DDP-specific state.
Since TLS sockets do not receive individual TCP segments but always
receive full TLS records, they can receive more data than is available
in the current window (e.g. if a 16k TLS record is received but the
socket buffer is itself 16k). To cope with this, just drop the window
to 0 when this happens, but track the overage and "eat" the overage as
it is read from the socket buffer not opening the window (or adding
rx_credits) for the overage bytes.
Reviewed by: np (earlier version)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D14529
- Change t4_ddp_mod_load() to return void instead of always returning
success. This avoids having to pretend to have proper support for
unloading when only part of t4_tom_mod_load() has run.
- If t4_register_uld() fails, don't invoke t4_tom_mod_unload() directly.
The module handling code in the kernel invokes MOD_UNLOAD on a module
whose MOD_LOAD fails with an error already.
Reviewed by: np (part of a larger patch)
MFC after: 1 month
Sponsored by: Chelsio Communications
Always terminate the list with -1 and document the ioctl behavior.
This preserves existing behavior as seen from userspace with the
addition of the unconditional termination which will not be seen by
working consumers of MDIOCLIST.
Because this ioctl can only be performed by root (in default
configurations) and is not used in the base system this bug is not
deemed to warrant either a security advisory or an eratta notice.
Reviewed by: kib
Obtained from: CheriBSD
Discussed with: security-officer (gordon)
MFC after: 3 days
Security: kernel heap buffer overflow
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14685
For _IO() ioctls, addr is a pointer to uap->data which is a caddr_t.
When the caddr_t stores an int, dereferencing addr as an (int *) results
in truncation on little-endian 64-bit systems and corruption (owing to
extracting top bits) on big-endian 64-bit systems. In practice the
value of chan was probably always zero on systems of the latter type as
all such FreeBSD platforms use a register-based calling convention.
Reviewed by: mav
Obtained from: CheriBSD
MFC after: 1 week
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14673
As noted in the comment, UEFI spec claims the capabilities pointer is
optional, but some implementations will choke and attempt to dereference it
without checking. This specific problem was found on a Lenovo Thinkpad X220
that would panic in efirtc_identify.
On x86 the IA-PC Boot Flags in the FADT can signal whether VGA is
available or not.
Sponsored by: Citrix systems R&D
Reviewed by: marcel
Differential revision: https://reviews.freebsd.org/D14397
The gcc 7 does check for switch statement fall through cases, and if legit,
such complaint can besilenced by /* FALLTHROUGH */ comment. Unfortunately
such comment is quite limited, but will still notify the reader.
This patch is backport from illumos, see
https://www.illumos.org/rb/r/941/
Reviewed by: eadler
Differential Revision: https://reviews.freebsd.org/D14663
For each regulators create an hw.regulator.<regname>. :
uvolt: Current value
always_on: 1 If the reg is always on
boot_on: 1 If the reg is set at boot time
enable_cnt: Number of consumer(s)
enable_delay: Delay before enabling the regulator
ramp_delay: The Ramp delay
max_uamp: The maximum value of the regulator in uAmps
min_uamp: The minimal value of the regulator in uAmps
max_uvolt: The maximum value of the regulator in uVolts
min_uvolt: The minimal value of the regulator in uVolts
Reviewed by: ian
Differential Revision: https://reviews.freebsd.org/D14578
These parameters may be changed via ifconfig(8); by default,
mgt / mcast rates are lowest possible and ucast rate is not set
(matches previous configuration).
While here, store some variables locally for better readability.
this check on open, but "iscsictl -M", or an iSCSI redirect received by
iscsid(8) could end up with two sessions with the same target name and
portal.
MFC after: 2 weeks
Move copy-pasted code for RTS/CTS frame allocation into net80211.
While here, add stat / debug message for allocation failures
(copied from run(4)) + return error here in bwn(4).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D14628
There is a difference when parsing a completion entry between Ethernet
and IB ports. When link layer is Ethernet the bits describe the type of
L3 header in the packet. In the case when link layer is Ethernet and VLAN
header is present the value of SL is equal to the 3 UP bits in the VLAN
header. If VLAN header is not present then the SL is undefined and consumer
of the completion should check if IB_WC_WITH_VLAN is set.
While that, this patch also fills the vlan_id field in the completion if
present.
linux commit 12f8fedef2ec94c783f929126b20440a01512c14
MFC after: 1 week
Sponsored by: Mellanox Technologies
mlx5core.
Do not consider the inability to create a firmware dump fatal, but
inform about the situation and allow the driver to attach. The device
might not implement the needed VSC, or we might not know the layout of
the registers map. In either case, only firmware dump functionality is
limited, the network operations should be fine.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When the mlx5en(4) driver was converted to using BUSDMA(9) the call to
m_defrag() was moved after the part of the TX routine that strips the
header from the mbuf chain. Before it called m_defrag it first trimmed
off the now-empty mbufs from the start of the chain. This has the side
effect of also removing the head of the chain that has M_PKTHDR set.
m_defrag() will not defrag a chain that does not have M_PKTHDR set,
thus it was effectively never defragging the mbuf chains.
As it turns out, trimming the mbufs in this fashion is unnecessary since
the call to bus_dmamap_load_mbuf_sg doesn't map empty mbufs anyway, so
remove it.
Differential Revision: https://reviews.freebsd.org/D12050
Submitted by: mjoras@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Set and report vport MTU rather than physical MTU,
The driver will set both vport and physical port mtu
and will rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Based on Linux upstream commit:
cd255efff9baadd654d6160e52d17ae7c568c9d3
Submitted by: Meny Yossefi <menyy@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Currently the ifnet interface is named mceX, where X is a monotonically
incremented value. If the device is reset due to a fatal error, then the
interface name will change. Using the device unit number will keep the
naming consistent across the reset logic.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add the ability to access the vendor specific space gateway in order
to support reading and writing data into the different configuration
domains.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for PFC and implement reading the per priority statistics
using the sysctl(8) interface. PFC is used together with VLAN priority
and can be enabled and disabled on a per priority basis.
Global pause frames and PFC are incompatible features and surrounding
logic has been added to warn the user about misconfiguration.
Update relevant mlx5core APIs for PFC configuration.
MFC after: 1 week
Sponsored by: Mellanox Technologies
ECN configuration and statistics is available through a set of sysctl(8)
nodes under sys.class.infiniband.mlx5_X.cong . The ECN configuration
nodes can also be used as loader tunables.
MFC after: 1 week
Sponsored by: Mellanox Technologies
