used a global pthread_mutex_t for synchronization. r179417 replaced that
with an implementation that directly used atomic instructions and thr_*
syscalls to synchronize callers to pthread_once. However, calling
pthread_mutex_lock on the global mutex implicitly ensured that
_thr_check_init() had been called but with r179417 this was no longer
guaranteed. This meant that if you were unlucky enough to have your first
call into libthr be a call to pthread_once(), you would segfault when
trying to access the pointer returned by _get_curthread().
The fix is to explicitly call _thr_check_init() from pthread_once().
Reviewed by: davidxu
Approved by: emaste (mentor)
MFC after: 1 week
While in_pseudo() etc. is often used in offloading feature support,
in_cksum() is mostly used to fix some broken hardware.
Keeping both around for the moment allows us to compile NIC drivers
even in an IPv6 only environment without the need to mangle them
with #ifdef INETs in a way they are not prepared for. This will
leave some dead code paths that will not be exercised for IPv6.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
Not compiling in and not initializing from inetsw from in_proto.c for
IPv6 only, we need to initialize upper layer protocols from inet6sw.
Make sure to not initialize them twice in a Dual-Stack
environment but only conditionally on no INET as we have done for
TCP for a long time. Otherwise we would leak resources.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
When compiling out INET we still need the initialization routines
as well as the tuning and montoring sysctls shared with IPv6.
Move the two send/recvspace variables up from the middle of the
file to ease compiling out the INET only code.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
Move the ipport_tick_callout and related functions from ip_input.c
to in_pcb.c. The random source port allocation code has been merged
and is now local to in_pcb.c only.
Use a SYSINIT to get the callout started and no longer depend on
initialization from the inet code, which would not work in an IPv6
only setup.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
Move fw_one_pass to where it belongs: it is a property of ipfw,
not of ip_input.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
experimental NFS client to take care of overflows for the calls
above the buffer cache layer in a manner similar to r220876.
Thanks go to dillon at apollo.backplane.com for providing the
snippet of code that does this.
MFC after: 2 weeks
experimental NFS client to take care of overflows. Thanks
go to dillon at apollo.backplane.com for providing the
snippet of code that does this.
MFC after: 2 weeks
now a suitable base for all kinds of egress queues.
- Add control queues (sge_ctrlq) and allocate one of these per hardware
channel. They can be used to program filters and steer traffic (and
more).
MFC after: 1 week
- If a ENH_SENS TLV section exit the firmware is capable of doing
enhanced sensitivity calibration.
- Newer devices/firmwares have more calibration commands therefore
hardcoding the noise gain/reset commands no longer works. It is
supposed to use the next index after the newest calibration type
support. Read the command index of the TLV section if available.
- We have two nodes connected and synchronized (local counters on both sides
are 0).
- We take secondary down and recreate it.
- Primary connects to it and starts synchronization (but local counters are
still 0).
- We switch the roles.
- Synchronization restarts but data is synchronized now from new primary
(because local counters are 0) that doesn't have new data yet.
This fix this issue we bump local counter on primary when we discover that
connected secondary was recreated and has no data yet.
Reported by: trociny
Discussed with: trociny
Tested by: trociny
MFC after: 1 week
This support has not worked for several years, and is not likely to work
again, unless Intel decides to release a native FreeBSD version of their
compiler. ;)
calculate required memory size dynamically.
- Fix races on chain re-lock.
- Introduce new field to ip_fw_chain - generation count. Now utilized
only in the NAT configuration, but can be utilized wider in ipfw.
- Get rid of NAT_BUF_LEN in ip_fw.h
PR: kern/143653
specified minimum and maximum. In case when specified default value
is out of bounds it does not work as expected and does not limit
variable. Check that default value is in range and limit it if needed.
Also bump max_hash_size value to 65536 to correspond with manual page.
PR: kern/152887
MFC after: 2 weeks
within the experimental NFS client. Mostly add mutex locking
and use the same rsize, wsize during the operation by keeping
a local copy of it. This is another change that brings it
closer to the regular NFS client.
MFC after: 2 weeks
adding the check to nfsrpc_close() isn't useful. Also,
the check in nfscl_getcl() must be more involved, since
it needs to check before and after the acquisition of
the refcnt on nfsc_lock, while the mutex that protects
the client state data is held.
background.
Suggested by: Garrett Cooper <yanegomi@gmail.com>
Use EAGAIN instead of magic value of -2 to report this condition from the
SetAliasAddressFromIfName routine.
MFC after: 2 weeks
