generation change if requested mode is async. The object generation is
only changed when the object is marked as OBJ_MIGHTBEDIRTY. For async
mode it is enough to write each dirty page, not to make a guarantee that
all pages are cleared after the vm_object_page_clean() returned.
Diagnosed by: truckman
Tested by: flo
Reviewed by: alc, truckman
MFC after: 2 weeks
in6m_release_locked() to defer calls to mld_v1_transmit_report() until
after the IF_ADDR_LOCK is dropped. This removes a race where the lock
is dropped and reacquired while attempting to walk an interface's
address list.
Reviewed by: bz
MFC after: 1 week
missing interface address list locking and grab a reference on the
matching interface address after dropping the lock while it is used to
avoid a potential use after free.
Reviewed by: bz
MFC after: 1 week
'comconsole_pcidev'. The former allows to set the base address of the
serial console i/o port. The later takes the string of the format
'bus:device:function:[bar]' as a value and uses the serial port attached
as PCI device at the specified location for console.
Both variants pass 'hw.uart.console' variable to the uart driver to
properly hand-over the kernel console.
Change allows to use ISA serial ports other than COM1 for the
loader/kernel console without loader recompilation. Also, you can use
PCI-attached port as the console, e.g. Intel AMT serial pseudo-port on
some motherboards based on Q67 chipset.
Reviewed by: jhb
MFC after: 2 weeks
Several callers of null_nodeget() did the cleanup itself, but several
missed it, most prominent being null_bypass(). Remove the cleanup from
the callers, now null_nodeget() handles lowervp free itself.
Reported and tested by: pho
MFC after: 1 week
This brings in the emuxkireg.h from NetBSD (dev/pci) which
is used for the same purpose but is smaller. The emu10k1
is now free from the GPL.
PR: 153901
Obtained from: NetBSD
Approved by: core (mentor implicit)
MFC after: 2 weeks
- Only initialize the per-cpu switchticks and switchtime in sched_throw()
for the very first context switch on APs during boot. This avoids a
small gap between the middle of thread_exit() and sched_throw() where
time is not accounted to any thread.
- In thread_exit(), update the timestamp bookkeeping to track the changes
to mi_switch() introduced by td_rux so that the code once again matches
the comment claiming it is mimicing mi_switch(). Specifically, only
update the per-thread stats directly and depend on ruxagg() to update
p_rux rather than adjusting p_rux directly. While here, move the
timestamp bookkeeping as late in the function as possible.
Reviewed by: bde, kib
MFC after: 1 week
- Actually increment ndomain when building our list of known domains
so that we can properly renumber them to be 0-based and dense.
- If the number of domains exceeds the configured maximum (VM_NDOMAIN),
bail out of processing the SRAT and disable NUMA rather than hitting an
obscure panic later.
- Don't bother parsing the SRAT at all if VM_NDOMAIN is set to 1 to
disable NUMA (the default).
Reported by: phk (2)
MFC after: 1 week
the number of links against LINK_MAX (which is INT16_MAX), not against
UINT32_MAX. Otherwise, the constant would implicitly be converted to
-1.
Reviewed by: pjd
MFC after: 1 week
reference on a group in the leaving state while iterating over the loop.
Instead, use the same approach used in igmp_ifdetach() and mld_ifdetach()
of placing the groups to free on pending release list and then releasing
the references after dropping the IF_ADDR_LOCK. This closes an ugly race
where the code was dropping the lock in the middle of iterating over the
list. It also fixes some additional potential use-after-free bugs since
the cancellation routine also applied other changes to the group after
dropping the reference. Now those changes are performed before the
reference is dropped and the group is potentially freed.
Prodded to fix by: glebius
Reviewed by: bz
MFC after: 1 week
of the SIOC[DG]LIFADDR icotls before dropping the IF_ADDR_LOCK() and
release the reference after using it. This prevents the address from
being potentially freed out from under the ioctl handler.
Reviewed by: bz
MFC after: 1 week
The index() and rindex() functions were marked LEGACY in the 2001
revision of POSIX and were subsequently removed from the 2008 revision.
The strchr() and strrchr() functions are part of the C standard.
This makes the source code a lot more consistent, as most of these C
files also call into other str*() routines. In fact, about a dozen
already perform strchr() calls.
is compared to an integer, by casting the pointer to l_uintptr_t. No
functional difference on both i386 and amd64.
Reviewed by: ed, jhb
MFC after: 1 week
passed to resource_list_add(). The rid that was just returned by
bus_alloc_resource_any() should have been used instead.
Reviewed by: jhb
MFC after: 1 week
include the MACHINE_CPUARCH directory if it differents from MACHINE when
building an index for a single machine. Also, include the 'x86' directory
when building an index for i386, pc98, or amd64.
MFC after: 1 week
sector size same as acd driver does. Together with r228808 and r228847 this
allows existing multimedia/vlc to play Audio CDs via CAM cd driver.
PR: ports/162190
MFC after: 1 week
As I looked through the C library, I noticed the FreeBSD MIPS port has a
hand-written version of index(). This is nice, if it weren't for the
fact that most applications call strchr() instead.
Also, on the other architectures index() and strchr() are identical,
meaning we have two identical pieces of code in the C library and
statically linked applications.
Solve this by naming the actual file strchr.[cS] and let it use
__strong_reference()/STRONG_ALIAS() to provide the index() routine. Do
the same for rindex()/strrchr().
This seems to make the C libraries and static binaries slightly smaller,
but this reduction in size seems negligible.
tmpfs_nocacheread(). It is both unnecessary and a pessimization. It
results in either the page being zeroed twice or zeroed first and then
overwritten by an I/O operation.
MFC after: 3 weeks
cam_periph_runccb() since the beginning checks it and releases device queue.
After r203108 it even clears CAM_DEV_QFRZN flag after that to avoid double
release, so removed code is unreachable now.
MFC after: 1 month
It seems strchr() and strrchr() are used more often than index() and
rindex(). Therefore, simply migrate all kernel code to use it.
For the XFS code, remove an empty line to make the code identical to
the code in the Linux kernel.
It was only used by ufs and ext2 and I have really strong doubts that
there are other pieces of code that also use this function. If it turns
out that external drivers use this code as well, I'd be happy to migrate
or revert.
Bump __FreeBSD_version while there.
While there, remove a useless check from the code. memcchr() always
returns characters unequal to 0xff in this case, so inosused[i] ^ 0xff
can never be equal to zero. Also, the fact that memcchr() returns a
pointer instead of the number of bytes until the end, makes conversion
to an offset far more easy.
It seems two of the file system drivers we have in the tree, namely ufs
and ext3, use a function called `skpc()'. The meaning of this function
does not seem to be documented in FreeBSD, but it turns out one needs to
be a VAX programmer to understand what it does.
SPKC is an instruction on the VAX that does the opposite of memchr(). It
searches for the non-equal character. Add a new function called
memcchr() to the tree that has the following advantages over skpc():
- It has a name that makes more sense than skpc(). Just like strcspn()
matches the complement of strspn(), memcchr() is the complement of
memchr().
- It is faster than skpc(). Similar to our strlen() in libc, it compares
entire words, instead of single bytes. It seems that for this routine
this yields a sixfold performance increase on amd64.
- It has a man page.
This shows that the majority of the weird traffic I see here are probe
frames that haven't been sent out, but I can also trigger this condition
by doing ICMP w/ -i 0.3 - enough to trigger the TX during actual scanning,
but not fast enough to stop scanning from occuring.
PR: kern/163689
comparing to struct timeval. for clocktime they should be
1..7 and 1..12 respectively
- CAPK-0100ND uses RTC without centruy bit (DS1307) so set it 21st
are booting inside a VM. There are three reasons to disable this:
o It causes the VM host to believe that all the tested pages or RAM are
in use. This in turn may force the host to page out pages of RAM
belonging to other VMs, or otherwise cause problems with fair resource
sharing on the VM cluster.
o It adds significant time to the boot process (around 1 second/Gig in
testing)
o It is unnecessary - the host should have already verified that the
memory is functional etc.
Note that this simply changes the default when in a VM - it can still be
overridden using the hw.memtest.tests tunable.
MFC after: 4 weeks
When r207410 eliminated the acquisition and release of the page queues
lock from pmap_extract_and_hold(), it didn't take into account that
pmap_pte_quick() sometimes requires the page queues lock to be held.
This change reimplements pmap_extract_and_hold() such that it no
longer uses pmap_pte_quick(), and thus never requires the page queues
lock.
Merge r177525 from the native pmap
Prevent the overflow in the calculation of the next page directory.
The overflow causes the wraparound with consequent corruption of the
(almost) whole address space mapping.
Strictly speaking, r177525 is not required by the Xen pmap because the
hypervisor steals the uppermost region of the normal kernel address
space. I am nonetheless merging it in order to reduce the number of
unnecessary differences between the native and Xen pmap implementations.
Tested by: sbruno
definition from K&R to ANSI, to avoid a clang warning about the uint8_t
parameter being promoted to int, which is not compatible with the type
declared in the earlier prototype.
MFC after: 1 week
All of these are harmless, and are in fact used to shut up warnings from
lint.
While here, remove -Wno-missing-prototypes from the xfs module
Makefile, as I could not reproduce those warnings either with gcc or
clang.
MFC after: 1 week
This is an AR71xx based board with 8MB flash, 64MB RAM, a
Mini-PCI+ slot (see below) and a single 10/100/1000baseT
ethernet port. It also has two USB ports.
This is an easier board than most to add as it doesn't have a
switch PHY on-board. This made it (mostly) trivial to craft a
working configuration.
Things to note:
* This, like most other reference boards, use uboot rather then
redboot. It means that you typically have to manually flash
both the kernel and rootfs partitions.
* Since there's currently no (nice) way to extract out the
ethernet MAC and RAM from the uboot environment, the RAM
will default to 32mb and the MAC will be something very
incorrect. I'll try to fix this up in a subsequent commit
or two, even if it's just some hard-coded nonsense in
ar71xx_machdep.c for now.
* The board is designed for a specific model of mini-PCI+
NIC which never made it into production. Normal mini-PCI
NICs will work fine; if you happen to have the NIC in question
then it will work fine with this board.
aspect of time stamp configuration per interface rather than per BPF
descriptor. Prior to this, the order in which BPF devices were opened and the
per descriptor time stamp configuration settings could cause non-deterministic
and unintended behaviour with respect to time stamping. With the new scheme, a
BPF attached interface's tscfg sysctl entry can be set to "default", "none",
"fast", "normal" or "external". Setting "default" means use the system default
option (set with the net.bpf.tscfg.default sysctl), "none" means do not
generate time stamps for tapped packets, "fast" means generate time stamps for
tapped packets using a hz granularity system clock read, "normal" means
generate time stamps for tapped packets using a full timecounter granularity
system clock read and "external" (currently unimplemented) means use the time
stamp provided with the packet from an underlying source.
- Utilise the recently introduced sysclock_getsnapshot() and
sysclock_snap2bintime() KPIs to ensure the system clock is only read once per
packet, regardless of the number of BPF descriptors and time stamp formats
requested. Use the per BPF attached interface time stamp configuration to
control if sysclock_getsnapshot() is called and whether the system clock read
is fast or normal. The per BPF descriptor time stamp configuration is then
used to control how the system clock snapshot is converted to a bintime by
sysclock_snap2bintime().
- Remove all FAST related BPF descriptor flag variants. Performing a "fast"
read of the system clock is now controlled per BPF attached interface using
the net.bpf.tscfg sysctl tree.
- Update the bpf.4 man page.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
In collaboration with: Julien Ridoux (jridoux at unimelb edu au)
before invoking the kernel.
Quoting submitter:
The issue is with the new boot loader menu. It adds many loader variables
including ones that contain ANSI color escapes.
Obviously, these ANSI codes don't play well with serial consoles when
kenv(1) is executed without arguments (reports vary as to what happens,
but it's never pretty).
The net-effect is that kenv(1) no longer reports menu-related variables.
In essence, kenv(1) output should now appear the same as on RELENG_8
(which lacks the new boot loader and didn't use any such variables).
Thus, restoring serial console glory.
Submitted by: Devin Teske <devin dott teske fisglobal.com>
MFC after: 2 weeks
with clang. There are several macros in these files that return values,
and in some cases nothing is done with them, but it is completely
harmless. For some other files, also disable -Wconstant-conversion,
since that triggers a false positive with the DMA_BIT_MASK() macro.
MFC after: 1 week
configurations for various architectures in FreeBSD 10.x. This allows
basic Capsicum functionality to be used in the default FreeBSD
configuration on non-embedded architectures; process descriptors are not
yet enabled by default.
MFC after: 3 months
Sponsored by: Google, Inc
with clang:
sys/dev/ce/tau32-ddk.c:1228:37: warning: implicit truncation from 'int' to bitfield changes value from 65532 to 8188 [-Wconstant-conversion]
Since this file is obfuscated C, we can never determine (in a sane way,
at least :) if this points to a real problem or not. The driver has
been in the tree for more than five years, so it most likely isn't.
MFC after: 1 week
asychronous task. This avoids tearing down multicast state including
sending IGMP leave messages and reprogramming MAC filters while holding
the per-protocol global pcbinfo lock that is used in the receive path of
packet processing.
Reviewed by: rwatson
MFC after: 1 month
While I'm here update if_oerrors if parent interface of vlan is not
up and running. Previously it updated collision counter and it was
confusing to interprete it.
PR: kern/163478
Reviewed by: glebius, jhb
Tested by: Joe Holden < lists <> rewt dot org dot uk >
decoded ranges. Pass any request for a specific range that fails because
it is not in a decoded range for an ACPI Host-PCI bridge up to the parent
to see if it can still be allocated. This is based on the assumption that
many BIOSes are inconsistent/broken and that settings programmed into BARs
or resources assigned to other built-in components are more trustworthy than
the list of decoded resource ranges in _CRS. This effectively limits the
decoded ranges to only being used for "wildcard" ranges when allocating
fresh resources for a BAR, etc. At some point I would like to only be
this permissive during an early scan of firmware-assigned resources during
boot and to be strict about all later allocations, but that isn't viable
currently.
MFC after: 2 weeks
at SCHED_PRI_RANGE to prevent overflows in the priority value. This can
happen due to irregularities with clock interrupts under certain
virtualization environments.
Tested by: Larry Rosenman ler lerctr org
MFC after: 2 weeks
bits.
The ROUERSTATION and RSPRO variants contain:
* the board specific bits (eg the RTC for RSPRO, later on it'll
include the GPIO/LED definitions);
* the boot specific bits (eg, on-board flash, usb flash, etc).
For now the AR71XX_BASE file contains the common board config,
drivers and net80211/ath wireless drivers.
I'll follow this up with config files for the other boards I
have (eg the Ubiquiti LSSR71, as well as some Mikrotik boards
that use the AR71XX and atheros reference boards) which will
be quite easy to do now.
no reason why it should be limited to 64K of DFLTPHYS. DMA data tag is any
way set to allow MAXPHYS, S/G lists (chain elements) are sufficient and
overflows are also handled. On my tests even 1MB I/Os are working fine.
Reviewed by: ken@
paravirtualized pmap implementations for i386. This includes some
style fixes to the native pmap and several bug fixes that were not
previously applied to the paravirtualized pmap.
Tested by: sbruno
MFC after: 3 weeks
In an example of boot command:
- rename wd(4) IDE disk drives name to ad(4) for the time being.
- update the used kernel path "/kernel" to the current default.
[It still worked occasionally by looking into the /boot/kernel directory,
so the resulting path was "/boot//kernel/kernel", with two slashes.]
Bump .Dd for this and previous changes.
MFC after: 1 week
doing split software/hardware LED configuration, we can now simply
treat "softled" as an "output" mux type.
This works fine on this DWA-552. Previous generation (pre-11n NICs) don't
have a GPIO mux - only input/output configuration - so they ignore this
field.
The hardware (MAC) LED blinking involves a few things:
* Selecting which GPIO pins map to the MAC "power" and "network" lines;
* Configuring the MAC LED state (associated, scanning, idle);
* Configuring the MAC LED blinking type and speed.
The AR5416 HAL configures the normal blinking setup - ie, blink rate based
on TX/RX throughput. The default AR5212 HAL doesn't program in any
specific blinking type, but the default of 0 is the same.
This code introduces a few things:
* The hardware led override is configured via sysctl 'hardled';
* The MAC network and power LED GPIO lines can be set, or left at -1
if needed. This is intended to allow only one of the hardware MUX
entries to be configured (eg for PCIe cards which only have one LED
exposed.)
TODO:
* For AR2417, the software LED blinking involves software blinking the
Network LED. For the AR5416 and later, this can just be configured
as a GPIO output line. I'll chase that up with a subsequent commit.
* Add another software LED blink for "Link", separate from "activity",
which blinks based on the association state. This would make my
D-Link DWA-552 have consistent and useful LED behaviour (as they're
marked "Link" and "Activity."
* Don't expose the hardware LED override unless it's an AR5416 or later,
as the previous generation hardware doesn't have this multiplexing
setup.
Some of the NICs I have here power up with the LEDs blinking, which is
incorrect. The blinking should only occur when the NIC is attempting
to associate.
* On powerup, set the state to HAL_LED_INIT, which turns on the "Power" MAC
LED but leaves the "Network" MAC LED the way it is.
* On resume, also init it to HAL_LED_INIT unless in station mode, where
it's forced to HAL_LED_RUN. Hopefully the net80211 state machine will
call newstate() at some point, which will refiddle the LEDs.
I've tested this on a handful of 11n and pre-11n NICs. The blinking
behaviour is slightly more sensible now.
relying on what the register defaults are.
This forces the blink mode to be proportional to the TX and RX frames
which match the RX filter.
This (along with a few tweaks to if_ath_led.c to configure the correct
GPIO pins) allows my DWA-552 AR5416 NIC to blink the LEDs in a useful
fashion, however those LEDs are marked "Link" and "Act(ivity)", which
don't really map well to the "power" / "network" LED interface which
the MAC provides. Some further tinkering is needed to see what other
useful operating modes are possible.
kernel builds. All the instances of this warning in our tree are
completely harmless, and many people seem to like adding extra
parentheses to make precedence clearer.
MFC after: 1 week
builds. All the instances of this warning in our tree are completely
harmless. (Most of the empty bodies look to be used simply as reminder
for the developer to add something later.)
While here, assign to CWARNEXTRA with ?=, so it can be overridden
easily, if needed.
MFC after: 1 week
to always evaluate to 0 if we are using a compiler that doesn't implement them.
This lets us use the macros easily in standard headers (e.g. stdatomic.h, which
should be the subject of my next commit).
Approved by: dim (mentor)
sysclock_getsnapshot() function allows the caller to obtain a snapshot of all
the system clock and timecounter state required to create time stamps at a later
point. The sysclock_snap2bintime() function converts a previously obtained
snapshot into a bintime time stamp according to the specified flags e.g. which
system clock, uptime vs absolute time, etc.
These KPIs enable useful functionality, including direct comparison of the
feedback and feed-forward system clocks and generation of multiple time stamps
with different formats from a single timecounter read.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
In collaboration with: Julien Ridoux (jridoux at unimelb edu au)
these to trigger a NOTE_ATTRIB EVFILT_VNODE kevent when the extended
attributes of a vnode are changed.
Note that OS X already implements this behavior.
Reviewed by: rwatson
MFC after: 2 weeks
As soon as not all devices support READ CAPACITY(16), automatically fall
back to READ CAPACITY(10) if CAM_REQ_INVALID or SSD_KEY_ILLEGAL_REQUEST
status returned.
It also provides first bits of information about Logical Block Provisioning
(aka UNMAP/TRIM) support by the device.
CWARNEXTRA variable, which gets included into the initial CWARNFLAGS
setting. This makes it easier to override CWARNFLAGS with completely
custom settings (including enabling any disabled warnings).
Reminded by: arundel
MFC after: 1 week
MS_SYNC flag. The system must guarantee that all writes are finished
before syscalls returned. Schedule the writes in async mode, which is
much faster and allows the clustering to occur. Wait for writes using
VOP_FSYNC(), since we are syncing the whole file mapping.
Potentially, the restriction to only apply the optimization can be
relaxed by not requiring that the mapping cover whole file, as it is
done by other OSes.
Reported and tested by: az
Reviewed by: alc
MFC after: 2 weeks
state from correctly updating things.
The reference driver directly enables/disables the LED state as required,
rather than nailing it up like it currently is. That'll have to come
later by adding some further HAL methods.
Obtained from: Atheros
* Bring the AR5416 GPIO mux mask code in line with the code from the
HAL.
* Add HAL_DEBUG_GPIO debugging statements, to track what's going on.
* Add Kiwi GPIO specific changes for reading values back.
Obtained from: Atheros
* As a preparation for AR9287 GPIO support, add in the AR9287 GPIO mask.
* Fix the association mask values; these are post-shift values but were
being shifted in twice. This resulted in some garbage being written
in the wrong place and the link LED (at least on my d-link AR5416
NIC) giving totally incorrect blink patterns.
Some users were reporting concurrent resets _were_ occuring - ie,
either two ath_reset()s ran at the same time (likely one on each CPU)
or ath_reset() versus ath_chan_change().
Instead, this now tries to grab the serialisation semaphore and will
pause() for a while if it fails. It will always eventually succeed though
and will log an error if it hits the recursion situation.
All of this stuff needs to die a horrible death at some point and be
replaced with a properly serialising method of programming this stuff
(eg using the net80211 taskqueue for all of this stuff.) The trouble
is figuring out how to handle the concurrent ioctl() based things without
introducing more LORs (which is another reason why I haven't just wrapped
all of this stuff in large, long-lived locks, a-la what Linux can get
away with.)
MFC after: Absolutely, positively never.
This doesn't fix compilation w/out AH_SUPPORT_AR5416 as all of the software
aggregation support in if_ath_tx.c and 11n code in if_ath_tx_ht.c touches
the 11n specific fields. I'll work on that later.
going on with the occasional garbage rs_antenna field reported by AR9285
users.
I've discovered that the 11n NICs only fill out the entire RX status
descriptor on the final descriptor in an aggregate. Some of the fields
(notably RSSI) are complete nonsense for A-MPDU subframes. This may
be another example of this.
The driver doesn't currently toss out statistics for non-final aggregate
frames. It's likely that this should be done.
If any users hit this particular debugging message they should report it
immediately to freebsd-wireless@freebsd.org - please ensure you have
ATH_DEBUG enabled so it prints out the full receive descriptor.
PR: kern/163312
jhb@ spotted that nfscl_getstateid() might modify credentials when
called from nfsrpc_read() for the case where p != NULL, whereas
nfsrpc_read() only did a crdup() to get new credentials for p == NULL.
This bug was introduced by r195510, since pre-r195510 nfscl_getstateid()
only modified credentials for the p == NULL case. This patch modifies
nfsrpc_read()/nfsrpc_write() so that they do crdup() for the p != NULL case.
It is conceivable that this bug caused the crash reported by glebius@, but
that will not be determined for some time, since the crash occurred after
about 1month of operation.
Tested by: glebius
Reviewed by: jhb
MFC after: 2 weeks
might be useful in some cases, but which are not severe enough to error
out the whole kernel build. Display them anyway, so there is at least
some incentive to fix them eventually.
Start with -Wtautological-compare warnings. These usually occur when
people check if unsigned quantities are negative, or similar cases. To
clean these up would be painful, and might give problems if the base
type which is compared against changes to signed later on.
MFC after: 1 week
connected via SAS or USB. Unluckily I've found that SAS (mps) and USB-SATA
I have translate models in different ways, requiring twice more quirks.
Unluckily for Hitachi, their model names are trimmed on SAS, making
impossible to identify 4K sector drives that way.
There's currently no public code which uses this feature and the
current reference driver doesn't enable this feature at all.
It's possible it was used by a previous version of the driver and
that indeed it should return HAL_STATUS; but at this point I'm
happy to require that they complain and submit a patch.
This was found by LLVM compile-time type checking.
Submitted by: dim
revision 1.122
date: 2009/05/13 01:01:34; author: dlg; state: Exp; lines: +6 -4
only keep track of the number of updates on tcp connections. state sync on
all the other protocols is simply pushing the timeouts along which has a
resolution of 1 second, so it isnt going to be hurt by pfsync taking up
to a second to send it over.
keep track of updates on tcp still though, their windows need constant
attention.
revision 1.120
date: 2009/04/04 13:09:29; author: dlg; state: Exp; lines: +5 -5
use time_uptime instead of time_second internally. time_uptime isnt
affected by adjusting the clock.
revision 1.175
date: 2011/11/25 12:52:10; author: dlg; state: Exp; lines: +3 -3
use time_uptime to set state creation values as time_second can be
skewed at runtime by things like date(1) and ntpd. time_uptime is
monotonic and therefore more useful to compare against.
revision 1.118
date: 2009/03/23 06:19:59; author: dlg; state: Exp; lines: +8 -6
wait an appropriate amount of time before giving up on a bulk update,
rather than giving up after a hardcoded 5 seconds (which is generally much
too short an interval for a bulk update).
pointed out by david@, eyeballed by mcbride@
revision 1.171
date: 2011/10/31 22:02:52; author: mikeb; state: Exp; lines: +2 -1
Don't forget to cancel bulk update failure timeout when destroying an
interface. Problem report and fix from Erik Lax, thanks!
Start a brief note of revisions merged from OpenBSD.
GEOM and using READ CD command for reading data, same as acd driver does.
Audio CDs identified by checking respective bit of the control field of
the first track in TOC.
This fixes bunch of error messages during boot (GEOM taste) with Audio CD
inserted and allows to grab Audio CD image using just dd.
MFC after: 1 month
import:
- Add read-only sysctls for all of the tunables supported by the igb and
em drivers.
- Make the per-instance 'enable_aim' sysctl truly per-instance by having it
change a per-instance variable (which is used to control AIM) rather
than having all of the per-instance sysctls operate on a single global
variable.
While here, restore the previously existing hw.igb.rx_processing_limit
tunable as it is very useful to be able to set a default tunable that
applies to all adapters in the system.
and sys/dev/ath/ath_hal/ar5416/ar5416_misc.c:
sys/dev/ath/ath_hal/ar5212/ar5212_misc.c:577:24: warning: implicit conversion from enumeration type 'HAL_STATUS' to different enumeration type 'HAL_BOOL' [-Wconversion]
return HAL_EINVAL;
~~~~~~ ^~~~~~~~~~
and:
sys/dev/ath/ath_hal/ar5416/ar5416_misc.c:164:9: warning: implicit conversion from enumeration type 'HAL_STATUS' to different enumeration type 'HAL_BOOL' [-Wconversion]
return HAL_OK;
~~~~~~ ^~~~~~
In both cases, enums HAL_BOOL and HAL_STATUS are mixed up.
MFC after: 1 week
and sys/dev/ath/ath_hal/ar5211/ar5211_power.c:
sys/dev/ath/ath_hal/ar5210/ar5210_power.c:36:3: warning: signed shift result (0x200000000) requires 35 bits to represent, but 'int' only has 32 bits [-Wshift-overflow]
OS_REG_RMW_FIELD(ah, AR_SCR, AR_SCR_SLE, AR_SCR_SLE_ALLOW);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sys/dev/ath/ath_hal/ah_internal.h:472:42: note: expanded from:
(OS_REG_READ(_a, _r) &~ (_f)) | (((_v) << _f##_S) & (_f)))
^
sys/dev/ath/ah_osdep.h:127:49: note: expanded from:
(bus_space_handle_t)(_ah)->ah_sh, (_reg), (_val))
^~~~
The AR_SCR_SLE_{WAKE,SLP,NORM} values are pre-shifted in ar5210reg.h and
ar5211reg.h, while they should be unshifted, like in ar5212reg.h. Then,
when the OS_REG_RMW_FIELD() macro shifts them again, the values will
overflow, becoming effectively zero.
MFC after: 1 week
At work, where we use use KVM+QEMU, we notice that pxeboot is pratically
impossible because of network timeouts. This is due to the fact that the
RTC code makes aggressive jumps.
Two RTC reads does not seem to be sufficient. Change the code to check
for 8 identical RTC values.
Sponsored by: Kumina bv
as it gets the following warning:
sys/dev/asr/asr.c:1836:29: warning: array index of '58' indexes past the end of an array (that contains 1 element) [-Warray-bounds]
while ((len > 0) && (sg < &((PPRIVATE_SCSI_SCB_EXECUTE_MESSAGE)
^
sys/dev/asr/i2omsg.h:934:8: note: array 'Simple' declared here
I2O_SGE_SIMPLE_ELEMENT Simple[1];
^
This is a false positive, since I2O_SG_ELEMENT::Simple is not declared
as a C99 flexible array member, but in the old (but more portable) way.
At run-time, the proper number of array elements will hopefully have
been allocated.
MFC after: 1 week
there are some places in the kernel where fixing them is too disruptive,
or where there is a false positive.
In this case, disable -Wconstant-conversion for two aic7xxx-related
files, as they get the following warning on i386 (and possibly on other
32-bit arches):
sys/dev/aic7xxx/ahc_pci.c:112:10: warning: implicit conversion from 'long long' to 'bus_addr_t' (aka 'unsigned int') changes value from 549755813887 to 4294967295 [-Wconstant-conversion]
? 0x7FFFFFFFFFLL
~~^~~~~~~~~~~~~~
This is a false positive, since the code only passes the 0x7FFFFFFFFFLL
argument, if sizeof(bus_addr_t) is larger than 4 (e.g. on 64 bit arches,
or when PAE is enabled on i386). The code could be refactored to do
compile-time checks, but that is more disruptive.
MFC after: 1 week
In the future we may want to perform the switch even if the console is
currently in the graphics mode by trying to reset the video adapter first
(e.g. by executing vesa/vga bios post). That would probably require
some sort of a one-way flag as returning the control of the console back
to the interrupted application most likely would result in a mess.
Reviewed by: emaste
MFC after: 2 months
This change is designed to let USB keyboard work in the panic context
with stop_scheduler_on_panic=1. Most of change consists of removing
mtx_owned() checks where they can be easily avoided. Some additional
lock cleanup is performed along the way.
A list of the smaller changes:
- newbus methods should be executed with Giant already held, just assert
this
- kbd methods called in the non-polling context should be executed with
Giant already held, just assert this
- Giant is recursive, so we should just take it where we must have it,
without redundant checks if we already have it
- thanks to recent syscons changes we don't need to go through the hoops
to detect if kernel is going to poll us; polling mode is now clearly
separated from non-polling mode
- at present the polling mode can be entered by only one thread
- document special cases in greater detail
Please note that the ukbd code and underlying USB code still lve
dangerously in the kdb context by trying to obtain various locks
including the Giant. If any of those locks are already held by the
stopped threads, then the things would blow up.
Another limitation of the ukbd driver is that it is detached before a
system enters the halt state.
With this commit we can enable kern.stop_scheduler_on_panic by default,
that should not introduce any regressions.
Reviewed by: hselasky
MFC after: 3 months
X-MFC after: r228424, r228760
When SCHEDULER_STOPPED() is true the mtx_owned() call may return
an unexpected and thus meaningless result.
So, in the code paths that can be reached when SCHEDULER_STOPPED() is true
we need to protect the mtx_owned() calls with the SCHEDULER_STOPPED()
checks and ensure that an appropriate branch is taken in each case.
Reviewed by: hselasky
MFC after: 3 months
X-MFC after: r228424
get a reply of EEXIST from an NFS server when a Mkdir RPC was retried,
for an NFS over UDP mount.
Upon investigation, it was found that the client was retransmitting
the Mkdir RPC request over UDP, but with a different xid. As such,
the retransmitted message would miss the Duplicate Request Cache
in the server, causing it to reply EEXIST. The kernel client side
UDP rpc code has two timers. The first one causes a retransmit using
the same xid and socket and was set to a fixed value of 3seconds.
(The default can be overridden via CLSET_RETRY_TIMEOUT.)
The second one creates a new socket and xid and should be larger
than the first. However, both NFS clients were setting the second
timer to nm_timeo ("timeout=<value>" mount argument), which defaulted to
1second, so the first timer would never time out.
This patch fixes both NFS clients so that they set the first timer
using nm_timeo and makes the second timer larger than the first one.
Reported by: jwd
Tested by: jwd
Reviewed by: jhb
MFC after: 2 weeks
initializing structures, like the pv table, that are only used to
implement superpages. In fact, some of the unnecessary code in
pmap_init() was actually doing harm. It was preventing the kernel from
booting on virtual machines with more than 768 MB of memory.
Tested by: sbruno
- Fix boot0 to check for PXE when using the pre-set setting for the
preferred slice.
- Update boot0cfg to use slice 6 to select PXE. Accept a 'pxe' argument
instead of a number for the 's' option as a way to select PXE as well.
Submitted by: Andrew Boyer aboyer averesystems
MFC after: 2 weeks
7.x, 8.x and 9.x with pf(4) imports: pfsync(4) should suppress CARP
preemption, while it is running its bulk update.
However, reimplement the feature in more elegant manner, that is
partially inspired by newer OpenBSD:
- Rename term "suppression" to "demotion", to match with OpenBSD.
- Keep a global demotion factor, that can be raised by several
conditions, for now these are:
- interface goes down
- carp(4) has problems with ip_output() or ip6_output()
- pfsync performs bulk update
- Unlike in OpenBSD the demotion factor isn't a counter, but
is actual value added to advskew. The adjustment values for
particular error conditions are also configurable, and their
defaults are maximum advskew value, so a single failure bumps
demotion to maximum. This is for POLA compatibility, and should
satisfy most users.
- Demotion factor is a writable sysctl, so user can do
foot shooting, if he desires to.
* Right now the delay is hard coded at 10uS. This is a bit long when doing lots
of periodic i2c transactions. So create a 'udelay' parameter and initialise it
to 10. This can be tuned later.
* Add a newline after a transaction finishes, so the debugging output isn't so
horrible.
performance issues.
* Access to the GPIO bus is already locked by requesting
and releasing the bus - thus the lock isn't really needed
for each GPIO pin change.
* Don't lock and unlock the GPIO bus for -each- i2c access -
the i2c bus code is already doing this by calling the upper
layer callback to request/release the bus. This thus locks
the bus for the entirety of the transaction.
TODO:
* Further verify that everything is correctly requesting/
releasing the GPIO bus.
* Look at how to lock the GPIO pin configuration stuff,
potentially by locking/unlocking the bus at the gpiobus
layer.
