queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
if_alloc() of ifp. This fixes the panic reported in the PR, but
not the attach failure.
PR: kern/139079
Tested by: Steven Noonan <steven uplinklabs.net>
Reviewed by: thompsa
Approved by: ed (mentor)
MFC after: 2 weeks`
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
rather than behind a seemingly accidental constant likely left over from one of
the related drivers which uses log levels rather than per-facility debugging
flags. This should get rid of contextless messages on the console for people
who have not set (or cleared the default) debugging flags.
packet. Linux, OpenBSD and our iwn(4) all do this. It also results in
a huge performance improvement (and the rejection of a fair number of
apparently-bad packets on receive) on my hardware.
o) Like the wpi(4) driver in OpenBSD, and like our iwn(4), also drop runt
packets.
o) Don't bother doing IFQ_POLL and then IFQ_DRV_DEQUEUE, just do
IFQ_DRV_DEQUEUE outright. This is more similar to how OpenBSD and our
iwn(4) work.
Reviewed by: sam
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
some longstanding issues:
o pass the vap since it's now the "coin of the realm" and required
to do things like set initial tx parameters in private node
state for use prior to association
o pass the mac address as cards that maintain outboard station
tables require this to create an entry (e.g. in ibss mode)
o remove the node table reference, we only have one node table
and it's unlikely this will change so this is not needed to
find the com structure
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
- Limit grabbing the lock to SIOCSIFFLAGS.
- Move ieee80211_start_all() to SIOCSIFFLAGS.
- Remove SIOCSIFMEDIA as it is not useful.
- Limit ether_ioctl to only SIOCGIFADDR. SIOCSIFADDR and SIOCSIFMTU have no
affect as there is no input/output path in the vap parent. The vap code
will handle the reinit of the mac address changes.
- Split off ndis_ioctl_80211 as it was getting too different to wired devices.
This fixes a copyout while locked and a lock recursion.
Reviewed by: sam
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
free function controlable, instead of passing the KVA of the buffer
storage as the first argument.
Fix all conventional users of the API to pass the KVA of the buffer
as the first argument, to make this a no-op commit.
Likely break the only non-convetional user of the API, after informing
the relevant committer.
Update the mbuf(9) manual page, which was already out of sync on
this point.
Bump __FreeBSD_version to 800016 as there is no way to tell how
many arguments a CPP macro needs any other way.
This paves the way for giving sendfile(9) a way to wait for the
passed storage to have been accessed before returning.
This does not affect the memory layout or size of mbufs.
Parental oversight by: sam and rwatson.
No MFC is anticipated.
The call should happen with the driver lock held. We don't hold the driver
lock in newstate as it's a separate thread where we can't sleep (and we only
call wpi_cmd in async mode).
Discovered By: Attillo's callout rework
Approved By: mlaier (comentor)
that the driver will handle WEP encryption. However, this does not seem to be
implemented by this driver (or maybe the chipset doesn't support it?)
Removing the flag makes my wpi card work using wpa_supplicant(8) on a
network with 802.1x security (without this change it authenticated fine, but
tcpdump only saw garbage packets)
Reviewed by: benjsc, imp (mentor)
Approved by: imp (mentor), sam
This import includes:
o wpi Wireless driver for the Intel 3945 Wireless Lan Controller (802.11abg) (sys/dev/wpi)
o Intel firmware revision 2.14.4 & associated LICENSE (sys/dev/contrib/wpi, sys/contrib/dev/wpi/LICENSE)
o wpifw Firmware driver (sys/modules/wpifw)
Approved by: mlaier, sam (co-mentors)
