when an interface is going down.
Right now it's quite possible (but very unlikely!) that ath_reset()
or similar is called, leading to a beacon config call, in parallel with
the last VAP being destroyed.
This likely should be fixed by making sure the bmiss/bstuck/watchdog
taskqueues are canceled whenever the last VAP is destroyed.
I couldn't think of a way to maintain the hardware TXQ locks _and_ layer
on top of that per-TXQ software queuing and any other kind of fine-grained
locks (eg per-TID, or per-node locks.)
So for now, to facilitate some further code refactoring and development
as part of the final push to get software queue ps-poll and u-apsd handling
into this driver, just do away with them entirely.
I may eventually bring them back at some point, when it looks slightly more
architectually cleaner to do so. But as it stands at the present, it's
not really buying us much:
* in order to properly serialise things and not get bitten by scheduling
and locking interactions with things higher up in the stack, we need to
wrap the whole TX path in a long held lock. Otherwise we can end up
being pre-empted during frame handling, resulting in some out of order
frame handling between sequence number allocation and encryption handling
(ie, the seqno and the CCMP IV get out of sequence);
* .. so whilst that's the case, holding the lock for that long means that
we're acquiring and releasing the TXQ lock _inside_ that context;
* And we also acquire it per-frame during frame completion, but we currently
can't hold the lock for the duration of the TX completion as we need
to call net80211 layer things with the locks _unheld_ to avoid LOR.
* .. the other places were grab that lock are reset/flush, which don't happen
often.
My eventual aim is to change the TX path so all rejected frame transmissions
and all frame completions result in any ieee80211_free_node() calls to occur
outside of the TX lock; then I can cut back on the amount of locking that
goes on here.
There may be some LORs that occur when ieee80211_free_node() is called when
the TX queue path fails; I'll begin to address these in follow-up commits.
EDMA HAL hardware.
* The EDMA HAL code assumes the nexttbtt and intval values are in TU/8
units, rather than TU. For now, just "hack" around that here, at least
until I code up something to translate it in the HAL.
* Setup some different TXQ flags for EDMA hardware.
* The EDMA HAL doesn't support setting the first rate series via
ath_hal_setuptxdesc() - instead, a call to ath_hal_set11nratescenario()
is always required. So for now, just do an 11n rate series setup
for EDMA beacon frames.
This allows my AR9380 to successfully transmit beacon frames.
However, CABQ TX and all normal data frame TX and TX completion is
still not functional and will require some more significant code churn
to make work.
The existing API only exposes 'seglen' (the current buffer (segment) length)
with the data buffer pointer set in 'ds_data'. This is fine for the legacy
DMA engine but it won't work for the EDMA engines.
The EDMA engine has a significantly different TX descriptor layout.
* The legacy DMA engine had a ds_data pointer at the same offset in the
descriptor for both TX and RX buffers;
* The EDMA engine has no ds_data for RX - the data is DMAed after the
descriptor;
* The EDMA engine has support for 4 TX buffer/segment pairs in the TX
DMA descriptor;
* The EDMA TX completion is in a different FIFO, and the driver will
'link' the status completion entry to a QCU by a "QCU ID".
I don't know why it's just not filled in by the hardware, alas.
So given that, here are the changes:
* Instead of directly fondling 'ds_data' in ath_desc, change the
ath_hal_filltxdesc() to take an array of buffer pointers as well
as segment len pointers;
* The EDMA TX completion status wants a descriptor and queue id.
This (for now) uses bf_state.bfs_txq and will extract the hardware QCU
ID from that.
* .. and this is ugly and wasteful; it should change to just store
the QCU in the bf_state and save 3/7 bytes in the process.
Now, the weird crap:
* The aggregate TX path was using bf_state->bfs_txq for the TXQ, rather than
taking a function argument. I've tidied that up.
* The multicast queue frames get put on a software TXQ and then that is
appended to the hardware CABQ when appropriate. So for now, make sure
that bf_state->bfs_txq points at the CABQ when adding frames to the
multicast queue.
* .. but the multicast queue TX path for now doesn't use the software
queue and instead
(a) directly sets up the descriptor contents at that point;
(b) the frames on the vap->avp_mcastq are then just appended wholesale
to the CABQ.
So for now, I don't have to worry about making the multicast path
work with aggregation or the per-TID software queue. Phew.
What's left to do:
* I need to modify the 11n ath_hal_chaintxdesc() API to do the same.
I'll do that in a subsequent commit.
* Remove bf_state.bfs_txq entirely and store the QCU as appropriate.
* .. then do the runtime "is this going on the right HWQ?" checks using
that, rather than comparing pointer values.
Tested on:
* AR9280 STA/AP
* AR5416 STA/AP
TX descriptor link pointers.
This is required for the AR93xx and later chipsets.
The RX path is slightly different - the legacy RX path directly
accesses ath_desc->ds_link for now, however this isn't at all done
for EDMA (FIFO) RX.
Now, for those performing a little software archeology here:
This is all a bit sub-optimal. "struct ath_desc" is only really relevant
for the pre-AR93xx NICs - where ds_link and ds_data is always in the
same location.
The AR93xx and later NICs have different descriptor layouts altogether.
Now, for AR93xx and later NICs, you should never directly reference
ds_link and ds_data, as:
* the RX descriptors don't have either - the data is _after_ the RX
descriptor. They're just one large buffer. There's also no need for
a per-descriptor RX buffer size as they're all fixed sizes.
* the TX descriptors have 4 buffer and 4 length fields _and_ a link
pointer. Each frame takes up one TX FIFO pointer, but it can contain
multiple subframes (either multiple frames in a buffer, and/or
multiple frames in an aggregate/RIFS burst.)
* .. so, when TX frames are queued to a hardware queue, the link
pointer is ONLY for buffers in that frame/aggregate. The next frame
starts in a new FIFO pointer.
* Finally, descriptor completion status is in a different ring.
I'll write something up about that when its time to do so.
This was inspired by Linux ath9k and the reference driver but is a
reimplementation.
Obtained from: Linux ath9k, Qualcomm Atheros
