aic7770 >= Rev E, aic7850, aic7860, aic7870, and ai7880 based controllers.
Make findSCB safer for non-tagged commands when tagged commands are
active on the controller. The symptoms of this problem were
"Overlapped commands attempted" messages during error recovery
attempts.
Compact scratch ram usage. This leaves 8 bytes free for future use.
Clean up some comments.
aic7xxx_reg.h:
Update my copyright.
- always use pci_conf_read() and pci_conf_write(). (This is required to
simulate non-existant devices in my system for PCI bridge code tests.)
- reorder some functions (put the main functions at the end).
- correct off by one bug in the code dealing with unitialized PCI to PCI
bridge chips. (Bug found by ASAMI Satoshi.)
- print function number for multi-function devices.
Fix support for the aic7850 by looking only at the relavent bits of the
QINCNT. The 7850 puts random garbage in the high bits and all my attempts
to determine the cause of this failed. This approach does seem to work
around the problem.
Don't trust SCSIPERR to tell us when there is a parity error. On
some revs of the 7870 and the 7880, this bit follows the parity of
the current byte. Instead of using a SEQINT to tell the kernel,
re-enable the standard parity error interrupt since it seems to pause
the sequencer right at the time of the error which is the effect we were
looking for anyway.
aic7xxx_reg.h:
Remove PARITY_ERROR seqeuncer interrupt type, its no longer used.
Define QCOUNTMASK as the SRAM location for the mask to use on the
QINCNT register. QCOUNTMASK is determined by the number of SCBs
supported by the device we're working on.
aic7xxx_asm.c
Properly check the return value of fopen, and define the arg list
in getopt correctly.
Submitted by: Pete Bentley <pete@demon.net>
Added scsi control devices.
Converted almost everything that I changed to use devfs_add_devswf()
and verbose id macros.
st.c:
Renamed enrst* to erst* since that's what the current name is (enrst
seems to be an old name).
mailing list.
When initiating a write, ccdbuffer() returns two "struct ccdbuf *"s
linked together by the cb_mirror field. "cb_pflags &
CCDPF_MIRROR_DONE" is set to 0 on both of them.
When a component returns to ccdiodone(), it checks if "cb_pflags &
CCDPF_MIRROR_DONE" is set or not. If not, it sets the partner's
flag and returns. If it is, it means its partner has already
returned, so it will go to the regular cleanup (which is in the
fallthrough code).
There should be no performance or functionality changes unless the
higher-level scsi driver does something with the resid value. The change
is purely aesthetical and prepares us for the parity implementation.
vm_offset_t is currently unsigned long but should probably be plain
unsigned for i386's to match the choice of minimal types to represent
for fixed-width types in Lite2. Anyway, it shouldn't be assumed
to be unsigned long.
I only fixed the type mismatches that were detected when I changed
vm_offset_t to unsigned. Only pointer type mismatches were detected.
1. Create 2 x 8k transmit buffer blocks in place of the 16k block previously.
With this change the speed as tested with ttcp on a 2Mbit link went up
from 206kbyte/s to 236kbyte/s.
2. Change the rest of the functions to also have the definition of the
return value on a sepperate line.
3. Remove some unused variables.
4. Add code to recover from DMA underruns.
5. Reorder ar_get_packets() to handle errors better.
6. Only allocate a mbuf cluster if the data is more than the mbuf.
(and in a second diff in addition to the above)
7. Stops the occasional DMA underruns that occurred when 2 channels
are running at 2Mbit/s.
Submitted by: John Hay <jhay@mikom.csir.co.za>
Cleanse the SCSI subsystem of its internally defined types
u_int32, u_int16, u_int8, int32, int16, int8.
Use the system defined *_t types instead.
eisaconf.c:
Cosmetic formatting chagnes.
iterations of 30uS so that really fast systems stop getting
timeout messages from the Riscom driver.
Reviewed by: ache, peter@nmti.com (Peter da Silva)
the S-Video input. It also has code in the driver for the meteor RGB support
and some other bug fixes. I don't have a meteor RGB but I have been told
that it works.
Submitted by: Jim Lowe <james@miller.cs.uwm.edu>
prevent it from conflicting with other drivers (like the aic7xxx driver).
Most of the work was in spliting out common portions of the driver and
making them generic enough to be called from the eisaconf probe.
The eisaconf probe for the 3Com 3c579 and the 3c509 when in eisa
configuration mode.
aha1742.c aic7770.c bt74x.c:
Only call eisa_registerdev after the probe is successfully.
eisaconf.c:
Increase kdc->kdc_datalen during the eisa_reg* functions instead of
in the eisa_add* functions since eisa_registerdev has already been
called and we have a kdc to manipulate.
port addresses (even though the PC architecture doesn't support them).
Add code to limit the I/O map size based on the lowest set bit of the
address. This cures the problem with the BT946C only having a 16 bit
map register, in voiolation of the PCI specs, without giving up the
general support of >65K port regions.
- Clean up the access to our ifnet structure by caching a pointer
to it instead of always digging through our softc structure.
Submitted by: Watchdog fixes by Serge A. Babkin <babkin@hq.icb.chel.su>
- fill in and use ifp->if_softc
- use if_bpf rather than private cookie variables
- change bpf interface to take advantage of this
- call ether_ifattach() directly from Ethernet drivers
- delete kludge in if_attach() that did this indirectly
- Call eisa_registerdev as soon as we have a device match. This allows the
"eisa_add_*" routines to tweak kdc_datalen as the kdc grows and shrinks.
eisaconf.c
- externalize the linked lists that hold our ioaddrs and maddrs.
caused by a different reason):
. #ifndef __FreeBSD__ around check for negative size, FreeBSD size_t is
unsigned
. Disable mirror/parity if interleave size is 0 (i.e., serial concatenation).
(1) The reads are always done from the first n/2 disks.
(2) Each write is done twice, to the "data" disk (in the first half) and
the "mirror" disk (in the second half).
ccdbuffer() now takes an extra argument (struct ccdbuf **) and stores
the pointer to ccdbuf in there. In case of a mirrored write, it
allocates and stores two pointers. The "residual" is also doubled
for mirrored writes so that ccdiodone() can correctly tell when all
the writes are done.
feature in the header type register, though it is required by the PCI spec.
This should correctly probe both functions of the Intel 82371FB chip,
without the need for a special case based on the device ID.
since setting up the DMA is too costly. Restructure for efficiency.
Pause the sequencer when a parity error occurs so that the kernel driver
knows during which phase the error was encountered.
includes a hack in the probe code: the 82371FB is a multifuction
device, but doesn't properly set the configuration bit which
indicates this. So, we just hard-wire all 82371FBs as multifunction
devices.
This does not actually make the bus-master IDE stuff work, although
if anyone wants to work on that, I have the databooks that tell
how to use it.
quite work yet, so the heart of it is disabled.
Added bdev and cdev args to dsopen().
drivers:
Fixed device names, links, minor numbers and modes.
wd.c:
Started actually supporting devfs.
diskslice.h:
Added devfs tokens to structs (currently 576 of them per disk! :-().
subr_diskslice.c:
Create devfs entries in dsopen() and (unsuccessfully) attempt to make
them go away at the right times. DEVFS is #undefed at the start so
that this shouldn't cause problems.
fd and wt drivers need bounce buffers, so this normally saves 32K-1K
of kernel memory.
Keep track of which DMA channels are busy. isa_dmadone() must now be
called when DMA has finished or been aborted.
Panic for unallocated and too-small (required) bounce buffers.
fd.c:
There will be new warnings about isa_dmadone() not being called after
DMA has been aborted.
sound/dmabuf.c:
isa_dmadone() needs more parameters than are available, so temporarily
use a new interface isa_dmadone_nobounce() to avoid having to worry
about panics for fake parameters. Untested.
the standard macro dbtob(). The non-B_PAGING case now works well enough
to run newfs on a 32GB virtual drive.
Fixed numerous bogus variable types and one overflowing multiplication
in the B_PAGING case of vnstrategy(). Swapping to virtual drives larger
than 2GB might work now.
SPIORDY just before we ack on the bus so that there is no chance to
see SPIORDY for the same byte twice.
Make some small modifications so that the Linux aic7xxx driver can use
our sequencer and register definition files verbatum.
Add the same type of safeguards we use in the mesg_in phase to the mesg_out
phase.
aic7xxx_reg.h:
Add definitions for the DSCommand register for PCI adapters.
aic7770.c:
Simplify the initialization of adapters by pulling all card specific
initialization to the card specific modules.
eisaconf.c:
outb 0x80 instead of 0xc80. The top byte is truncated anyway, and 0x80
was what was intended.
1) Use cpp to preprocess the sequencer code.
2) Convert all "magic numbers" to #defines shared by the sequencer and
kernel driver via the aic7xxx_reg.h file. (The assembler still needs
to be re-written in lex/yacc to allow ~|& type constructions).
3) Raise ATN on parity errors for "in" phases and send an initiator detected
error or message-in parity error message as appropriate.
4) Turn off the reselection hardware from the time or a (re)connection to
busfree. It seems that some fast targets were able to reconnect before
the sequencer was able to see busfree.
5) The message buffer is considered "in-use" when there is a positive length
count. The ACTIVE_MSG flag was unnecesary.
6) Properly set SCB_NEXT_WAITING to SCB_LIST_HEAD in scbs being added to
the waiting scb list. This is a change in how the list code works to
facilitate some planned work in the reset code.
7) The fields in the SCB have be re-arranged to be quad-word aligned.
8) The inb code has been rewritten to catch phasemisses and be more efficient.
9) Go back to "snooping the bus" to determine if the incomming identify
message will be followed by a simple queue message. Its much faster than
doing a search through the SCBs.
10) Implement better tag range checking for incomming tags.
11) Make sdtr_to_rate more accurate (use 25 instead of 24 in calculations -
must have been asleep that night).
12) Rearrange some routines to reduce code complexity and size.
13) Update comments and formatting.
14) Fixed bugs I've forgotten about??
Reviewed by: David Greenman <davidg@FreeBSD.org>
enough nodes for the number of ports on the last module, not the number
of ports _total_ that the driver is managing...
Submitted by: Robert Sanders <rsanders@mindspring.com>
Fixed panics for events on nonexistent ports.
Fixed devconf class initialization and devconf state tracking.
Submitted by: Serge A. Babkin <babkin@hq.icb.chel.su>
unintentionally committed):
- the fifo was completely disabled for low speeds. Apart from being
unnecessarily inefficient, this invalidated com->tx_fifo_size.
- `ftl' became a bogus name.
- the 16650 probe breaks the COM_NOFIFO() case and has other bugs
(disabled, not fixed).
Fixed bogus change of the fifo settings for the non-speed of 0. This
bug made the above fifo bug occur even at non-low speeds.
Fixed the modes of the cua devices. It isn't possible to set the uid
and gid correctly since the kernel can't know who uucp.dialer is.
Register the devswitch at device attach time. SYSINIT() is not
the right way to initialize devswitches (if anything :->).
Eventually, the devswitch should be deregistered at device detach
and/or unload time and reregistered at device attach time ... Then
some com->gone tests could be removed.
Cleaned up some other recent changes.
#includes to get prototypes.
pci now uses a different interrupt handler type for interrupts that it
dispatches and the isa interrupt handler type for the interrupts that
it handles.
Reduce default value of pcicb_membase to 0x2000000 (from 0x4000000)
since this seems to be the lower bound used by many systems.
Submitted by: Mihoko Tanaka <m_tanaka@pa.yokogawa.co.jp>
getmajorbyname() which were a better (sigh) temporary interface to
the going-away devswitches.
Note that SYSINIT()s to initialize the devswitches would be fatal
in syscons.c and pcvt_drv.c (and are bogus elsewhere) because they
get called independently of whether the device is attached; thus
devices that share a major clobber each other's devswitch entries
until the last one wins.
conf.c:
Removed stale #includes and comments.
seems to work hre just fine though I can't check every file
that changed due to limmited h/w, however I've checked enught to be petty
happy withe hte code..
WARNING... struct lkm[mumble] has changed
so it might be an idea to recompile any lkm related programs
device must be configured. It's hard to tell whether a reset function
should be noreset or nullreset since reset functions are never called.
Most drivers use nullreset but noreset has the advantage of complaining
if somehow gets called).
Removed old aliases d_rdwr_t and d_ttycv_t for d_read_t/d_write_t and
d_devtotty_t.
Sorted declarations of switch functions into switch order.
Removed duplicated comments and declarations of nonexistent switch
functions.
most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
to get the definitions of TRUE and FALSE which happen to be defined in
a deeply nested include.
Added nearby #includes of <sys/conf.h> where appropriate.
Fixed two cases of "=" that should have been "==" in card type comparison.
Simplified expression that checks for interface up/down.
Moved ed_ring_copy to before its first use so that it's inlined as intended.
Change mbuf allocation policy so that a received packet is stored in just
an mbuf header (no cluster) if it will fit in one.
Removed ifnet.if_init and ifnet.if_reset as they are generally unused.
Change the parameter passed to if_watchdog to be a ifnet * rather than
a unit number. All of this is an attempt to move toward not needing an
array of softc pointers (which is usually static in size) to point to
the driver softc.
if_ed.c:
Changed some of the argument passing to some functions to make a little
more sense.
if_ep.c, if_vx.c:
Killed completely bogus use of if_timer. It was being set in such a way
that the interface was being reset once per second (blech!).
conflicted with S3 graphics cards. Now users should put sio[2-3]
in the config file if the hardware exisst, even if the probe is
certain to fail due to an interrupt conflict. Otherwise, ports
sharing the interrupt may fail the probe if the system is warm
booted while sio[2-3] are active (perhaps under another OS). The
same problem for nonstandard ports is now handled better than
before.
That's EVERY SINGLE driver that has an entry in conf.c..
my next trick will be to define cdevsw[] and bdevsw[]
as empty arrays and remove all those DAMNED defines as well..
Each of these drivers has a SYSINIT linker set entry
that comes in very early.. and asks teh driver to add it's own
entry to the two devsw[] tables.
some slight reworking of the commits from yesterday (added the SYSINIT
stuff and some usually wrong but token DEVFS entries to all these
devices.
BTW does anyone know where the 'ata' entries in conf.c actually reside?
seems we don't actually have a 'ataopen() etc...
If you want to add a new device in conf.c
please make sure I know
so I can keep it up to date too..
as before, this is all dependent on #if defined(JREMOD)
(and #ifdef DEVFS in parts)
o Add signed/unsigned functionality to the matrox meteor device driver.
o Apply a few fixes to the sound driver.
o Add a ``SPIGOT_UNSECURE'' compile time definition so, if one defines
SPIGOT_UNSECURE in their conf file, then they can use the spigot w/o
root. There is a warning that this allows users access to the IO
page which is probably not secure.
Submitted by: james
totally dynamic.
this is only the devices in i386/isa
I'll do more tomorrow.
they're completely masked by #ifdef JREMOD at this stage...
the eventual aim is that every driver will do a SYSINIT
at startup BEFORE the probes, which will effectively
link it into the devsw tables etc.
If I'd thought about it more I'd have put that in in this set (damn)
The ioconf lines generated by config will also end up in the
device's own scope as well, so ioconf.c will eventually be gutted
the SYSINIT call to the driver will include a phase where the
driver links it's ioconf line into a chain of such. when this phase is done
then the user can modify them with the boot: -c
config menu if he wants, just like now..
config will put the config lines out in the .h file
(e.g. in aha.h will be the addresses for the aha driver to look.)
as I said this is a very small first step..
the aim of THIS set of edits is to not have to edit conf.c at all when
adding a new device.. the tabe will be a simple skeleton..
when this is done, it will allow other changes to be made,
all teh time still having a fully working kernel tree,
but the logical outcome is the complete REMOVAL of the devsw tables.
By the end of this, linked in drivers will be exactly the same as
run-time loaded drivers, except they JUST HAPPEN to already be linked
and present at startup..
the SYSINIT calls will be the equivalent of the "init" call
made to a newly loaded driver in every respect.
For this edit,
each of the files has the following code inserted into it:
obviously, tailored to suit..
----------------------somewhere at the top:
#ifdef JREMOD
#include <sys/conf.h>
#define CDEV_MAJOR 13
#define BDEV_MAJOR 4
static void sd_devsw_install();
#endif /*JREMOD */
---------------------somewhere that's run during bootup: EVENTUALLY a SYSINIT
#ifdef JREMOD
sd_devsw_install();
#endif /*JREMOD*/
-----------------------at the bottom:
#ifdef JREMOD
struct bdevsw sd_bdevsw =
{ sdopen, sdclose, sdstrategy, sdioctl, /*4*/
sddump, sdsize, 0 };
struct cdevsw sd_cdevsw =
{ sdopen, sdclose, rawread, rawwrite, /*13*/
sdioctl, nostop, nullreset, nodevtotty,/* sd */
seltrue, nommap, sdstrategy };
static sd_devsw_installed = 0;
static void sd_devsw_install()
{
dev_t descript;
if( ! sd_devsw_installed ) {
descript = makedev(CDEV_MAJOR,0);
cdevsw_add(&descript,&sd_cdevsw,NULL);
#if defined(BDEV_MAJOR)
descript = makedev(BDEV_MAJOR,0);
bdevsw_add(&descript,&sd_bdevsw,NULL);
#endif /*BDEV_MAJOR*/
sd_devsw_installed = 1;
}
}
#endif /* JREMOD */
it `const' to inhibit compiler warnings.
Added #include of <pccard/driver.h> to get prototypes. <pccard/slot.h>
is still necessary for its side effect of exporting non-slot things.
HD64570 chip. Both the 2 and 4 port cards is supported and auto detected.
Line speeds of up to 2Mbps is possible. At this speed about 85% of the
bandwidth is usable with 486DX processors.
The standard FreeBSD sppp code is used for the link level layer. The
default protocol used is PPP. The Cisco HDLC protocol can be used by
adding "link2" to the ifconfig line in /etc/sysconfig or where ever
ifconfig is run.
At the moment only the V.35 and X.21 interfaces is supported. The others
may need tweaks to the clock selection code.
Submitted by: John Hay <jhay@mikom.csir.co.za>
Convert the remaining sysctl stuff to the new way of doing things.
the devconf stuff is the reason for the large number of files.
Cleaned up some compiler warnings while I were there.
floppies must have been random in 2.x since we reintroduced sorting
on b_pblkno on 1995/03/18. Drivers still initialize b_cylin/b_resid
although this is no longer used.
Removed unused, wrong function fdsize(). (Returning 0 means that the
device exists and has size 0, not that the device doesn't exist.
swaponvp() allows for size 0 by stupidly calling the d_psize function
twice if the size isn't 0. setdumpdev() doesn't allow for it.)
Continued removing /* ARGSUSED */ from drivers.
from a string to an identifier so that it can be used to generate
declarations and strings. It's much easier to stringize an identifier
than to identifize a string. A uniform naming scheme must be used
for the automatically generated things to apply. This is a feature.
Used the module identifer to generate prototypes for the module load,
unload and stat functions. Removed the few prototypes for these that
already existed.
Used the module identifier to generate a unique struct tag in MOD_DEV().
This should probably be done for all the MOD_*() macros.
Moved the trailing semicolon from the MOD_*() macro definitions to the
macro invocations that didn't already (bogusly) have it.
Staticized the module load and unload functions.
Added function return types for the module load, unload and stat functions.
lkm/ibcs2/ibcs2.c:
Included <sys/sysproto.h> to get everything prototyped.
Cleaned up #includes.
lkm/ibcs2/ipfw.c:
Cleaned up #includes.
lkm/linux/linux.c:
The module name had to change from "linux_emulator" to "linux_mod" to
be automatically generated.
Cleaned up #includes.
lkm/syscons/*/*_saver.c:
Completed delcarations of function pointers.
sys/i386/isa/atapi.c:
The module name had to change from "atapi" to "atapi_mod" to be
automatically generated.
sys/i386/isa/wcd.c:
Used the fixed MOD_DEV(). This module has two devices and expanded the
macro in the source instead of fixing it.
The module names had to change from "wcd" and "rwcd" to "wcd_mod" and
"rwcd_mod" to be automatically generated.
sys/pccard/pcic.c:
The module name had to change from "pcic" to "pcic_mod" to be
automatically generated.
Most of this is cleaning up, but there are some functional changes,
doc/comment improvements, error checking, gcc -Wall cleanups. Input buffer
flushing is enabled now, although I'm still not quite certain it's right.
Handle kdc registration correctly. Catch ISA devices that use eisa
registration and output probe information accordingly.
lsdev will have to be updated to handle EISA devices correctly.
aic7770.c:
Set kdc_isa0 as the parent for 284X cards since its a VL card.
cards like the Adaptec 284x that use EISA ID registers for identification
even when in stalled in non-EISA systems.
Use one format throught the files.
-Wall fixes.
be the beginning of our move to a more dynamic (configuration manager)
based setup for all drivers. Everything seems to work except for
some devconf problems. Only the aic7xxx driver will be using this
interface until it is reviewed, revised and accepted as a good configuration
interface.
Adapt aic7770.c to use new eisaconf.
eisadevs.c is replaced by a linker set.
misplaced extern declarations (mostly prototypes of interrupt handlers)
that this exposed. The prototypes should be moved back to the driver
sources when the functions are staticalized.
Added idempotency guards to <machine/conf.h>. "ioconf.h" can't be
included when building LKMs so define a wart in bsd.kmod.mk to help
guard against including it.
/dev/random is now a part of the kernel! you will need to make
the device in /dev: sh MAKEDEV random
and take a look at some test code in src/tools/test/random.
to <machine/conf.h>. conf.h was mechanically generated by
`grep ^d_ conf.c >conf.h'. This accounts for part of its ugliness. The
prototypes should be moved back to the driver sources when the functions
are staticalized.
Remove confusing backwards compatibility code that allowed driver to be
used in pre-4.4 releases. The 3COM card's use -link2 to switch tranceivers.
(no functional changes here)
This code will only be included in your kernel if you have
'options DEVRANDOM', but that will fall away in a couple of days.
Obtained from: Theodore Ts'o, Linux
convention of having their entry point named "<modname>_mod"".
Symorder is enforcing this when the current bsd.kmod.mk is installed.
I've not tested all these, but at least they all compile now.
Reattach them to the makefile.
Note that the change that I made to symorder needs to be compiled and
installed before any LKM's will work - the last version was corrupting
the relocation tables. A "make world" will to this, but if you
manually run a make on the lkm's you'll need to take care of it by
hand.
in each phase routine. Saves a few instructions.
Be more careful in how we deal with SXFRCTL0. Or in the control bits of
interest instead of using mvi. The kernel driver will set the ULTRAEN
bit of SXFRCTL0 if we are using Ultra (20MHz) mode and we don't want to
clobber it.
In sdtr_to_rate divide by two if we are in ultra mode to get the correct
setting since its a 20MHz instead of 10MHz scale.
Submitted by: Mike Mitchell, supervisor@alb.asctmd.com
This is a bulk mport of Mike's IPX/SPX protocol stacks and all the
related gunf that goes with it..
it is not guaranteed to work 100% correctly at this time
but as we had several people trying to work on it
I figured it would be better to get it checked in so
they could all get teh same thing to work on..
Mikes been using it for a year or so
but on 2.0
more changes and stuff will be merged in from other developers now that this is in.
Mike Mitchell, Network Engineer
AMTECH Systems Corporation, Technology and Manufacturing
8600 Jefferson Street, Albuquerque, New Mexico 87113 (505) 856-8000
supervisor@alb.asctmd.com
"I screwed the initialization of the burstsize. Right now it will default
to 0 (which can cause corruption problems on high latency PCI buses). It
should be set to 8 longwords to avoid problems with certain PCI chipsets."
Submitted by: Matt Thomas <matt@lkg.dec.com>
Fix the tests for being a console by reverting to the ones that
were used before the the RB_SERIAL changes. RB_SERIAL only needs
to be tested in one place. The initialization of comconsole was
wrong before the RB_SERIAL changes for the COMCONSOLE case. This
may have been the cause of the unnecessary changes.
Start eliminating #includes of <i386/i386/cons.h>. This header is
supposed to be included from <machine> although it should be
completely machine-independent and included from <sys>.
Remove a wrong XXX comment. `comconsole' is used to test for being
a console and even the tests for deciding the default termios state
are necessary (the semi-reentrant i/o routines don't handle ordinary
device i/o).
cy.c:
Sync with sio.c. The console tests are present but always fail.
and here is the patch. Submit it please. Thank you!
BTW, there is a new option "NDGBPORTS". By default it is equal to
NDGB*16 and means the number of ports of all Digiboards for which the
tty structures are reserved. It can be set to the real value in config-file
like:
options "NDGBPORTS=8"
Submitted by: Serge A. Babkin <babkin@hq.icb.chel.su>
scheduled for demolition. This is a first step: get rid of if_zereg.h,
by adding the five extra definitions to if_edreg.h.
Also add some definitions which will become needed when if_ze.c gets
replaced entirely by pccard and if_ed.c. (this is a 2.1.0 candidate)
with the driver's stability now. I've not had a single problem with it for
weeks.. All that remains is a bit of performance tuning, and finishing
the manpages.
Add prototypes. Use static for function definitions to match existing
prototypes. Otherwise leave functions that should be static as extern.
TODO: declare everthing except sidriver and siintr as static. I use
some new cdevs registration functions to do this for syscons and pcvt.
Fix siintr() to match its prototype in ioconf.c (don't return anything).
This may break the eisa support, but Julian says that eisa interrupts
never worked anyway.
(EISA support was never tested anyway - Peter)
Submitted by: bde
the first one in the config has priority. They can be switched using
userconfig().
i386/i386/conf.c:
Initialize the shared syscons/pcvt cdevsw entry to `nx'.
Add cdevsw registration functions.
Use devsw functions of the correct type if they exist.
i386/i386/cons.c:
Add renamed syscons entry points to constab.
i386/i386/cons.h:
Declare the renamed syscons entry points.
i386/i386/machdep.c:
Repeat console initialization after userconfig() in case the current
console has become wrong. This depends on cn functions not wiring down
anything important.
sys/conf.h:
Declare new functions.
i386/isa/isa.[ch]:
Add a function to decide which display driver has priority. Should be
done better.
i386/isa/syscons.c:
Rename pccn* -> sccn*.
Initialize CRTC start address in case the previous driver has moved it.
i386/isa/syscons.c, i386/isa/pcvt/*
Initialize the bogusly shared variable Crtat dynamically in case the
stored value was changed by the previous driver.
Initialize cdevsw table from a template.
Don't grab the console if another display driver has priority.
i386/isa/syscons.h, i386/isa/pcvt/pcvt_hdr.h:
Don't externally declare now-static cdevsw functions.
i386/isa/pcvt/pcvt_hdr.h:
Set the sensitive hardware flag so that pcvt doesn't always have lower
priority than syscons. This also fixes the "stupid" detection of the
display after filling the display with text.
i386/isa/pcvt/pcvt_out.c:
Don't be confused the off-screen cursor offset 0xffff set by syscons.
kern/subr_xxx.c:
Add enough nxio/nodev/null devsw functions of the correct type for syscons
and pcvt.
