modules to depend on modules in the same file (uhub depends on usb) or
even on themselves (usb on usb, makes the define in usb_port.h a lot
less convoluted).
Use ANSI prototypes.
There is a number of devices that are compliant, of which the 3Com 5605 is
has been verified to work.
The driver is not perfect yet, but should be able to get you somewhere.
The driver was originally written by Lennart Augustsson, but Mike Smith
and Mike Meyer <mwm@mired.org> did the porting.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
routines from foo_watchdog() because foo_watchdog() is called at
interrupt context, and that's a no-no due to the way the USB stack
is currently set up.
What we do now is call the TX end of frame handler manually to clear
the completed transmission, then check the send queue and send off
any frames that are pending.
Also turned off the interrupt pipe stuff in if_aue, since it appears
to tickle a bug in the USB stack that I haven't found yet.
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
ums driver (mouse) and get the usb driver at the same time.
This also shows that
MODULE_VERSION(usb, 1);
MODULE_DEPEND(usb, usb, 1, 1, 1);
in the same module in one source file works.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
(which is actually a CATC Netmate).
Gee. I don't know why people make such a fuss over supporting USB ethernet
NICs. This is easier than collecting graft.
Update the license in the rio_usb.h (now rio500_usb.h) to not be GPL.
Sorry for committing that file in the first place. The change of license
was agreed to by the original author.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
unit numbers all wrong. This did not show up because most of them where
zero anyway.
Use a separate buffer for command transforms instead of fiddling with
the existing cdb_bytes.
Take CAM_CDB_POINTER into account. Nobody is using it, but someone might
in the future.
Be more picky about what to accept in the UFI command set.
First attempt at implementing the ATAPI command protocol transforms.
This should at least make Imation Superdisk and other e-Shuttle based
devices show as attached. Maybe they even work to some extent.
contains the ADMtek Pegasus AN986 USB chipset. The
adapter supports both 10BaseT and 100BaseT (including
full-duplex). The product code for these adapters is
0x2206.
and has not been loaded via a kldload,
running usbd(8) will autoload the "usb.ko" kld.
thanks to Peter Wemm for enlightening me on the
differences between kldfind(2) and modfind(2).
to be based on the transfer speed, but I got it all wrong. The by far
biggest factor in the timeout is the start of a removable device, which
is about 2 seconds anyway.
Prodded by: Lennart Augustsson
This makes it possible to handle the done queue even when the end of tail
TD has ended up on the done queue as well (the xfer in this case is NULL
but the next field is valid, so we simply skip that element.
Make sure we mark all the handled transfers as handled.
Stop using powerhooks. They are a NetBSD-ism.
