regulatory domain with the "country" parameter, but will also take a full
country name. The man page warns that only the ISO code is unambiguous.
In reality, however, the first match on either would be accepted, leading
to "DE" being interpreted as the "DEBUG" country rather than Germany, and
"MO" selecting Morocco rather than the correct country, Macau.
Fix this by always checking for an ISO CC match first, and only search on
the full country name if that fails.
PR: bin/140571
Tested by: Dirk Meyer dirk.meyer dinoex.sub.org
Reviewed by: sam
Approved by: ed (mentor)
MFC after: 1 month
lookup {dst-ip|src-ip|dst-port|src-port|uid|jail} N
which searches the specified field in table N and sets tablearg
accordingly.
With dst-ip or src-ip the option replicates two existing options.
When used with other arguments, the option can be useful to
quickly dispatch traffic based on other fields.
Work supported by the Onelab project.
MFC after: 1 week
"split" is very ineffective for devices with rotating media as HDDs.
To be effective, it needs that transfer time reduction due to block
splitting was bigger then access time increase due to non-sequential
access. For modern HDDs I was able to reproduce it only with read sizes
of 2MB and above, which is almost not applicable in real life.
"load" algorithm same time is more universal and effective now.
Reviewed by: pjd
it seems that now it is necessary for 'forward' to work outside lo0.
The bug (and fix) was reported on 8.0. This patch probably applies
to RELENG_7 as well.
It seems that 'pf' has a similar bug.
Submitted by: Lytochkin Boris
MFC after: 3 days
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
logwtmp() gets called with the raw strings that are written to disk. For
regular user entries, this isn't too bad, but when booting/shutting
down, the contents get rather cryptic.
Just call the standardized pututxline().
long as I remember, and completely superseded by better maintained umass(4).
It's main idea was to optionally avoid CAM dependency for such devices, but
with move ATA to CAM, it is not actual any more.
No objections: hselasky@, thompsa@, arch@
- Extend XPT-SIM transfer settings control API. Now it allows to report to
SATA SIM number of tags supported by each device, implement ATA mode and
SATA revision negotiation for both SATA and PATA SIMs.
- Make ahci(4) and siis(4) to use submitted maximum tag number, when
scheduling requests. It allows to support NCQ on devices with lower tags
count then controller supports.
- Make PMP driver to report attached devices connection speeds.
- Implement ATA mode negotiation between user settings, device and
controller capabilities.
- Add support for sector size > 512 bytes and physical sector of several
logical sectors, introduced by ATA-7 specification.
- Remove some obsoleted code.
Right now sysctl just prints the major/minor numbers of a device.
Instead of rolling our own routine for this, we'd better just call
devname(3) to perform a translation to a device name for us.
portion of the capture buffer (db_capture_bufoff vs db_capture_bufsize).
This could result in outputting garbage (e.g. lots of 'p' characters if
DIAGNOSTIC is enabled) after the end of the capture buffer. While here,
fix a spelling nit.
Reported by: Mikolaj Golub to my trociny of gmail
MFC after: 3 days
value is preceded by an option without value (for example -o
option1,option2=value). Options must be separated before searching for
'='. Also compare pnextopt explicitly against NULL.
PR: bin/134069
Approved by: trasz (mentor)
packets instead of allowing the protocol stack to pick a random source port.
This fixes the behaviour where dhclient would never transition from RENEWING
to BOUND without going through REBINDING in networks which are paranoid about
DHCP spoofing, such as most mainstream cable-broadband ISP networks.
Reviewed by: brooks
Obtained from: OpenBSD (partly - I'm not convinced their solution can work)
MFC after: 1 week (pending re approval)
Don't clobber *p with '\0' when testing whether it has the value of 'F'.
Just use the semantics of strtof() properly. If it returns p, we know
that it parsed the string until it reached 'C' or 'F'.
The code has not changed since it has been imported (r161951, Sep 3,
2006).
Submitted by: Alexandre Perrin <kaworu@kaworu.ch>
MFC after: 1 week
actually initialized. In the growfs case for UFS2, no inodes were actually
being initialized and the number of inodes noted as initialized was the
number of inodes per group. This created a filesystem that was deemed
corrupted because the inodes thus added were full of garbage.
MFC after: 1 month
re-add $ipv6_enable support for backward compatibility. From
UPDATING:
1. To use IPv6, simply define $ifconfig_IF_ipv6 like $ifconfig_IF
for IPv4. For aliases, $ifconfig_IF_aliasN should be used.
Note that both variables need the "inet6" keyword at the head.
Do not set $ipv6_network_interfaces manually if you do not
understand what you are doing. It is not needed in most cases.
$ipv6_ifconfig_IF and $ipv6_ifconfig_IF_aliasN still work, but
they are obsolete.
2. $ipv6_enable is obsolete. Use $ipv6_prefer and/or
"inet6 accept_rtadv" keyword in ifconfig(8) instead.
If you define $ipv6_enable=YES, it means $ipv6_prefer=YES and
all configured interfaces have "inet6 accept_rtadv" in the
$ifconfig_IF_ipv6. These are for backward compatibility.
3. A new variable $ipv6_prefer has been added. If NO, IPv6
functionality of interfaces with no corresponding
$ifconfig_IF_ipv6 is disabled by using "inet6 ifdisabled" flag,
and the default address selection policy of ip6addrctl(8)
is the IPv4-preferred one (see rc.d/ip6addrctl for more details).
Note that if you want to configure IPv6 functionality on the
disabled interfaces after boot, first you need to clear the flag by
using ifconfig(8) like:
ifconfig em0 inet6 -ifdisabled
If YES, the default address selection policy is set as
IPv6-preferred.
The default value of $ipv6_prefer is NO.
4. If your system need to receive Router Advertisement messages,
define "inet6 accept_rtadv" in $ifconfig_IF_ipv6. The rc(8)
scripts automatically invoke rtsol(8) when the interface becomes
UP. The Router Advertisement messages are used for SLAAC
(State-Less Address AutoConfiguration).
