It turns out on a 16550 w/ a 25MHz SoC reference clock you get a little
over 3% error at 115200 baud, which causes this to fail.
Just .. cope. Things cope these days.
Default to 30 (3.0%) as before, but allow UART_DEV_TOLERANCE_PCT to be
set at build time to change that.
vendor supplied device trees contain the needed properties for us to select
the correct uart to use as the kernel console.
An example of this would be to add the following to loader.conf.
hw.fdt.console="/smb/uart@f7113000"
The intention of this is slightly different than the existing
hw.uart.console option. The new option will mean the boot serial
configuration will be derived from the device node, while the existing
option expects the user to configure all this themselves.
Further work is planned to allow the uart configuration to be set based on
the stdout-path property devicetree bindings.
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D3559
electrical signals on the serial port. Virtually all devices which output a
PPS signal generate a brief higher-voltage pulse, the leading edge of which
is the on-time point.
Both DCD and CTS are active-low signals on the wire, meaning the assertion
of their status bits in the modem status register corresponds to the lower
voltage level on the wire. So when the status bit transitions to not-set,
create a PPS assert event; when the status bit transitions to set, create a
PPS clear event.
eliminating the need to build a custom kernel to use the CTS signal.
The historical UART_PPS_ON_CTS kernel option is still honored, but now it
can be overridden at runtime using a tunable to configure all uart devices
(hw.uart.pps_mode) or specific devices (dev.uart.#.pps_mode). The per-
device config is both a tunable and a writable sysctl.
This syncs the PPS capabilities of uart(4) with the enhancements recently
recently added to ucom(4) for capturing from USB serial devices.
Relnotes: yes
time_pps_fetch() to be used in blocking mode.
Also, don't init the pps api for system devices (consoles) that provide a
custom attach routine. The device may actually be a keyboard or other non-
tty device. If it wants to do pps processing (unlikely) it must handle
everything for itself. (In reality, only a sun keyboard uses a custom
attach routine, and it doesn't make a good pps device.)
uart_bus_attach() during its test that 20 iterations weren't sufficient
for clearing all pending interrupts, assuming this means that hardware
is broken and doesn't deassert interrupts. However, under pressure, 20
iterations also can be insufficient for clearing all pending interrupts,
leading to a panic as intr_event_handle() tries to schedule an interrupt
handler not registered. Solve this by introducing a flag that is set in
test mode and otherwise restores pre-r253161 behavior of uart_intr(). The
approach of additionally registering uart_intr() as handler as suggested
in PR 194979 is not taken as that in turn would abuse special pccard and
pccbb handling code of intr_event_handle(). [1]
- Const'ify uart_driver_name.
- Fix some minor style bugs.
PR: 194979 [1]
Reviewed by: marcel (earlier version)
MFC after: 3 days
polling at device attach time [1].
Add tunables 'debug.uart_force_poll' and 'debug.uart_poll_freq' to control
uart polling.
Submitted by: Aleksey Kuleshov (rndfax@yandex.ru) [1]
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
uart implementations, and export them using the new linker-set mechanism.
Differential Revision: https://reviews.freebsd.org/D1993
Submitted by: Michal Meloun
(class and device) FDT UART. Define second one, UART_FDT_CLASS, for UART
class only.
This paves the way for declaring uart_class data and ofw/fdt compat data
with a uart implementation, rather than needing a big global table of
compat data and weak-symbol declarations of every existing implementation.
Differential Revision: https://reviews.freebsd.org/D1992
Submitted by: Michal Meloun
is the case, depending on the options, in some of the ARM hardware
simulators. In these cases we don't get an interrupt so will need to
schedule the task to write more data to the uart.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
chips with the same device and vendor IDs actually may provide different
functionality. While at it, canonicalize the description to match other
MosChip UARTs.
PR: 186891
MFC after: 3 days
This will allow to attach UART drivers lying directly on the root node
instead of simple-bus compatible bus only.
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Instead of waiting for empty TX FIFO it is more reasonable to
block on full FIFO. As soon as FIFO slot is free the character
can be transmitted.
In case of TX FIFO disabled, TXFF bit indicates that transmit
register is not empty.
Obtained from: Semihalf
Reviewed by: andrew, emaste
Sponsored by: The FreeBSD Foundation
in userland rename in-kernel getenv()/setenv() to kern_setenv()/kern_getenv().
This fixes a namespace collision with libc symbols.
Submitted by: kmacy
Tested by: make universe
doesn't have support for the Z8530. Embedded PowerPC platforms
typically don't. Fail when the device class we actually need is
not present.
Obtained from: Juniper Networks, Inc.
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
uart2: <Intel AMT - PM965/GM965 KT Controller> port 0x1830-0x1837
mem 0xfe024000-0xfe024fff irq 17 at device 3.3 on pci0
uart2: console (115200,n,8,1)
Tested as tty and serial console. Seems "fine"
