- change the type of pm_active to cpumask_t, which it is;
- in pmap_remove_pages(), compare with PCPU(curpmap), instead of
dereferencing the long chain of pointers [1].
For amd64 pmap, remove the unneeded checks for validity of curpmap
in pmap_activate(), since curpmap should be always valid after
r209789.
Submitted by: alc [1]
Reviewed by: alc
MFC after: 3 weeks
ABI specifies the DF should be zero, and newer compilers do not clear
DF before using DF-sensitive instructions.
The DF clearing for signal handlers was done some time ago.
MFC after: 1 week
writing event timer drivers, for choosing best possible drivers by machine
independent code and for operating them to supply kernel with hardclock(),
statclock() and profclock() events in unified fashion on various hardware.
Infrastructure provides support for both per-CPU (independent for every CPU
core) and global timers in periodic and one-shot modes. MI management code
at this moment uses only periodic mode, but one-shot mode use planned for
later, as part of tickless kernel project.
For this moment infrastructure used on i386 and amd64 architectures. Other
archs are welcome to follow, while their current operation should not be
affected.
This patch updates existing drivers (i8254, RTC and LAPIC) for the new
order, and adds event timers support into the HPET driver. These drivers
have different capabilities:
LAPIC - per-CPU timer, supports periodic and one-shot operation, may
freeze in C3 state, calibrated on first use, so may be not exactly precise.
HPET - depending on hardware can work as per-CPU or global, supports
periodic and one-shot operation, usually provides several event timers.
i8254 - global, limited to periodic mode, because same hardware used also
as time counter.
RTC - global, supports only periodic mode, set of frequencies in Hz
limited by powers of 2.
Depending on hardware capabilities, drivers preferred in following orders,
either LAPIC, HPETs, i8254, RTC or HPETs, LAPIC, i8254, RTC.
User may explicitly specify wanted timers via loader tunables or sysctls:
kern.eventtimer.timer1 and kern.eventtimer.timer2.
If requested driver is unavailable or unoperational, system will try to
replace it. If no more timers available or "NONE" specified for second,
system will operate using only one timer, multiplying it's frequency by few
times and uing respective dividers to honor hz, stathz and profhz values,
set during initial setup.
This information can be very valuable for CPU sleep-time (and respectively
idle power consumption) optimization.
Add counters for timer-related IPIs.
Reviewed by: jhb@ (previous version)
FPU/SSE hardware. Caller should provide a save area that is chained
into the stack of the areas; pcb save_area for usermode FPU state is
on top. The pcb now contains a pointer to the current FPU saved area,
used during FPUDNA handling and context switches. There is also a
facility to allow the kernel thread to use pcb save_area.
Change the dreaded warnings "npxdna in kernel mode!" into the panics
when FPU usage is not registered.
KPI discussed with: fabient
Tested by: pho, fabient
Hardware provided by: Sentex Communications
MFC after: 1 month
APIC interrupt that fires when a threshold of corrected machine check
events is reached. CMCI also includes a count of events when reporting
corrected errors in the bank's status register. Note that individual
banks may or may not support CMCI. If they do, each bank includes its own
threshold register that determines when the interrupt fires. Currently
the code uses a very simple strategy where it doubles the threshold on
each interrupt until it succeeds in throttling the interrupt to occur
only once a minute (this interval can be tuned via sysctl). The threshold
is also adjusted on each hourly poll which will lower the threshold once
events stop occurring.
Tested by: Sailaja Bangaru sbappana at yahoo com
MFC after: 1 month
arbitrary frequencies into hardclock(), statclock() and profclock() calls.
Same code with minor variations duplicated several times over the tree for
different timer drivers and architectures.
- Switch all x86 archs to new functions, simplifying the code and removing
extra logic from timer drivers. Other archs are also welcome.
Extend struct sysvec with three new elements:
sv_fetch_syscall_args - the method to fetch syscall arguments from
usermode into struct syscall_args. The structure is machine-depended
(this might be reconsidered after all architectures are converted).
sv_set_syscall_retval - the method to set a return value for usermode
from the syscall. It is a generalization of
cpu_set_syscall_retval(9) to allow ABIs to override the way to set a
return value.
sv_syscallnames - the table of syscall names.
Use sv_set_syscall_retval in kern_sigsuspend() instead of hardcoding
the call to cpu_set_syscall_retval().
The new functions syscallenter(9) and syscallret(9) are provided that
use sv_*syscall* pointers and contain the common repeated code from
the syscall() implementations for the architecture-specific syscall
trap handlers.
Syscallenter() fetches arguments, calls syscall implementation from
ABI sysent table, and set up return frame. The end of syscall
bookkeeping is done by syscallret().
Take advantage of single place for MI syscall handling code and
implement ptrace_lwpinfo pl_flags PL_FLAG_SCE, PL_FLAG_SCX and
PL_FLAG_EXEC. The SCE and SCX flags notify the debugger that the
thread is stopped at syscall entry or return point respectively. The
EXEC flag augments SCX and notifies debugger that the process address
space was changed by one of exec(2)-family syscalls.
The i386, amd64, sparc64, sun4v, powerpc and ia64 syscall()s are
changed to use syscallenter()/syscallret(). MIPS and arm are not
converted and use the mostly unchanged syscall() implementation.
Reviewed by: jhb, marcel, marius, nwhitehorn, stas
Tested by: marcel (ia64), marius (sparc64), nwhitehorn (powerpc),
stas (mips)
MFC after: 1 month
architecture from page queue lock to a hashed array of page locks
(based on a patch by Jeff Roberson), I've implemented page lock
support in the MI code and have only moved vm_page's hold_count
out from under page queue mutex to page lock. This changes
pmap_extract_and_hold on all pmaps.
Supported by: Bitgravity Inc.
Discussed with: alc, jeffr, and kib
In the end, it does help fixing /dev/io usage from multithreaded
processes.
- On i386 and amd64 the old behaviour is kept but multithreaded
processes must use the new interface in order to work well.
- Support for the other architectures is greatly improved, where
necessary, by the necessity to define very small things now.
Manpage update will happen shortly.
Sponsored by: Sandvine Incorporated
PR: threads/116181
Reviewed by: emaste, marcel
MFC after: 3 weeks
domain clock, 8 programmable PMC.
- Westmere based CPU (Xeon 5600, Corei7 980X) support.
- New man pages with events list for core and uncore.
- Updated Corei7 events with Intel 253669-033US December 2009 doc.
There is some removed events in the documentation, they have been
kept in the code but documented in the man page as obsolete.
- Offcore response events can be setup with rsp token.
Sponsored by: NETASQ
for parsing model-specific and other fields in machine check events
including the global machine check capabilities and status registers,
CPU identification, and the FreeBSD CPU ID.
- Report these added fields in the console log of a machine check so that
a record structure can be reconstituted from the console messages.
- Parse new architectural errors including memory controller errors.
MFC after: 1 week
for upcoming 64-bit PowerPC and MIPS support. This renames the COMPAT_IA32
option to COMPAT_FREEBSD32, removes some IA32-specific code from MI parts
of the kernel and enhances the freebsd32 compatibility code to support
big-endian platforms.
Reviewed by: kib, jhb
processors. With this workaround, superpage promotion can be re-enabled
under virtualization. Moreover, machine check exceptions can safely be
enabled when FreeBSD is running natively on Family 10h processors.
Most of the credit should go to Andriy Gapon for diagnosing the error and
working with Borislav Petkov at AMD to document it. Andriy also reviewed
and tested my patches.
Discussed with: jhb
MFC after: 3 weeks
correctly initialized and just then assign to softclock/profclock.
Right now, some atrtc seems reporting strange diagnostic error* making the
current pattern bogus.
In order to do that cleanly, lapic_setup_clock(), on both ia32 and amd64,
now accepts as arguments the desired sources to handle, and returns the
actual ones (LAPIC_CLOCK_NONE is forbidden because otherwise there is no
meaning in calling such function).
This allows to bring out into commont x86 code the handling part for
machdep.lapic_allclocks tunable, which is retained.
Sponsored by: Sandvine Incorporated
Tested by: yongari, Richard Todd
<rmtodd at ichotolot dot servalan dot com>
MFC: 3 weeks
X-MFC: r202387, 204309
This header file uses __packed, without including <sys/cdefs.h>. This
means it cannot be used in the way described in sysarch(3) by only
including <machine/sysarch.h>.
LAPIC may lead to aliasing for softclock and profclock because frequencies
are sized in order to fit mainly hardclock.
atrtc used to take care of the softclock and profclock and it does still
do, if the LAPIC can't handle the clocks properly.
Revert the change when the LAPIC started taking charge of all three of
them and let atrtc handle softclock and profclock if not explicitly
requested. Such request can be made setting != 0 the new tunable
machdep.lapic_allclocks or if the new device ATPIC is not present
within the i386 kernel config (atrtc is linked to atpic presence).
Diagnosed by: Sandvine Incorporated
Reviewed by: jhb, emaste
Sponsored by: Sandvine Incorporated
MFC: 3 weeks
I/O port access is implemented on Itanium by reading and writing to a
special region in memory. To hide details and avoid misaligned memory
accesses, a process did I/O port reads and writes by making a MD system
call. There's one fatal problem with this approach: unprivileged access
was not being prevented. /dev/io serves that purpose on amd64/i386, so
employ it on ia64 as well. Use an ioctl for doing the actual I/O and
remove the sysarch(2) interface.
Backward compatibility is not being considered. The sysarch(2) approach
was added to support X11, but support for FreeBSD/ia64 was never fully
implemented in X11. Thus, nothing gets broken that didn't need more work
to begin with.
MFC after: 1 week
sys/vmmeter.h: warning: shadowed declaration is here
machine/cpufunc.h: In function 'insw':
machine/cpufunc.h: warning: declaration of 'cnt' shadows a global declaration
..snip..
- directly print mca information in case we fail to allocate memory
for a record
- include bank number into mca record
- print raw mca status value for extended information
Reviewed by: jhb
MFC after: 10 days
not properly set up. r199067 added the call to TUNABLE_INT_FETCH() to
initializecpu() that results in hang because AP are started when kernel
environment is already dynamic and thus needs to acquire mutex, that is
too early in AP start sequence to work.
Extract the code that should be executed only once, because it sets
up global variables, from initializecpu() to initializecpucache(),
and call the later only from hammer_time() executed on BSP. Now,
TUNABLE_INT_FETCH() is done only once at BSP at the early boot stage.
In collaboration with: Mykola Dzham <freebsd levsha org ua>
Reviewed by: jhb
Tested by: ed, battlez
handlers. This is primarily intended as a way to allow devices that use
multiple interrupts (e.g. MSI) to meaningfully distinguish the various
interrupt handlers.
- Add a new BUS_DESCRIBE_INTR() method to the bus interface to associate
a description with an active interrupt handler setup by BUS_SETUP_INTR.
It has a default method (bus_generic_describe_intr()) which simply passes
the request up to the parent device.
- Add a bus_describe_intr() wrapper around BUS_DESCRIBE_INTR() that supports
printf(9) style formatting using var args.
- Reserve MAXCOMLEN bytes in the intr_handler structure to hold the name of
an interrupt handler and copy the name passed to intr_event_add_handler()
into that buffer instead of just saving the pointer to the name.
- Add a new intr_event_describe_handler() which appends a description string
to an interrupt handler's name.
- Implement support for interrupt descriptions on amd64 and i386 by having
the nexus(4) driver supply a custom bus_describe_intr method that invokes
a new intr_describe() MD routine which in turn looks up the associated
interrupt event and invokes intr_event_describe_handler().
Requested by: many
Reviewed by: scottl
MFC after: 2 weeks
by looking at the bases used for non-relocatable executables by gnu ld(1),
and adjusting it slightly.
Discussed with: bz
Reviewed by: kan
Tested by: bz (i386, amd64), bsam (linux)
MFC after: some time
specify their own version of atomic_cmpset_* which could have been
different than the membar version.
Right now, however, FreeBSD is bound mostly to GCC-like compilers and
it is desired to add new support and compat shim mostly when there is
a real necessity, in order to avoid too much compatibility bloats.
In this optic, bring back atomic_cmpset_{acq, rel}_* to be the same as
atomic_cmpset_* and unwind the atomic_cmpset_barr_* introduction.
Requested by: jhb
Reviewed by: jhb
Tested by: Giovanni Trematerra <giovanni dot trematerra at
gmail dot com>
not defined through macros or similar) in order to be later compiled in
the kernel and offer this way the support for modules (and
compatibility among the UP case and SMP case).
Fix this for the newly introduced atomic_cmpset_barr_* cases by defining
and specifying a template. Note that the new DEFINE_CMPSET_GEN()
template save more typing on amd64 than the current code. [1]
- Fix the style for memory barriers on amd64.
[1] Reported by: Paul B. Mahol <onemda at gmail dot com>
memory barriers should also ensure that the compiler doesn't reorder paths
where they are used. GCC, however, does that aggressively, even in
presence of volatile operands. The most reliable way GCC offers for avoid
instructions reordering is clobbering "memory" even if that is
theoretically an heavy-weight operation, flushing the content of all
the registers and forcing reload of them (We could rely, however, on
gcc DTRT by just understanding the purpose as this is a well-known
pattern for many modern operating-systems).
Not all our memory barriers, right now, clobber memory for GCC-like
compilers. The most notable cases are IA32 and amd64 where the memory
barrier are treacted the same as normal atomic instructions.
Fix this by offering the possibility to implement atomic instructions
with memory barriers separately from the normal version and implement
the GCC-like specific one using memory clobbering.
Thanks to Chris Lattner (@apple) for his discussion on llvm specifics.
Reported by: jhb
Reviewed by: jhb
Tested by: rdivacky, Giovanni Trematerra
<giovanni dot trematerra at gmail dot com>
startup and genericize it so it can be reused to map other tables as well:
- Add a routine to walk a list of ACPI subtables such as those used in the
APIC and SRAT tables in the MI acpi(4) driver.
- Move the routines for mapping and unmapping an ACPI table as well as
mapping the RSDT or XSDT and searching for a table with a given signature
out into acpica_machdep.c for both amd64 and i386.
