- Fixed bogus CIS tuple dumping (Network node ID, IRQ modes and etc.)
- Include telling drivers ethernet address if Network node ID
tuple is available. This is usefull for some bogus ehter cards which
can't get correct ethernet address from CIS tupple.
Obtained from: PAO3
o Modify xe driver to use this.
There's still some issues with this code, so xe can't map the cis just
yet. I'm thinking about how to resolve the issue. pccard_nbk's
pccard_alloc_resource is getting in the way.
This don't hurt anything.
PCI/CardBus Bridge -> PCI-CardBus Bridge
Submitted by: Takeshi Shibagaki <sibagaki@lsi.melco.co.jp>
Obtained from: bsd-nomads ML in Japan
cardbus bridge init routine for all cardbuses. This routine attempts
to compensate for BIOSes that do not setup the cardbus bridge into
legacy mode. Since this is becoming more common, and cardbus pci
cards have appeared on the market, this makes sense.
Do some TI113x specific initialization. This came in as part of the
patch. Report TI1[1234]XX specific config registers protected by
bootverbose.
Minor code cleanup while I'm here. I've also removed the unused code
present in the original patches, and cleaned it up slightly in places
as well.
The original patches supported more than one card, but these patches
support just one. We should likely revisit this in the future.
This makes the Compaq card that Walnut Creek CD purchased for me work
in my bouncer box.
This is a MFC candidate. However, I'd like to get some airtime on
these patches on as many laptops as possible before doing the MFC. It
does change things somewhat. In theory, apart from the minor TI
tweaks, this shouldn't change anything if the bridge is in legacy mode
already.
Submitted by: sanpei@sanpei.org (MIHIRA Yoshiro)
o break out some of the probe routine the allocation of resources
into an attach routine
o Recognize PnP ids
o Allocate IRQ per card rather than per system
o Better polling reporting
o Remove unneeded include files in slot.h
o store a pseudo unit number on each device we find.
o Pass a unit number to interrupt/timeout routine and use it for polling
the hardware.
Tested on: My VAIO and with the Linksys pccard reader.
Approved by: jkh
conversion to eliminate the compatability shims without making any
significant changes. This eliminates the shim warnings.
Obtained from: n_himba (tweaked by me, don't blame him for this)
Approved by: jkh
Many ed-based Ethernet PC-cards can't get correct MAC address without
this patch.
Submitted by: Takanori Watanabe <takawata@shidahara1.planet.sci.kobe-u.ac.jp>
Reviewed by: Warner Losh <imp@village.org>
For example, when /etc/pccard.conf had ed0 in config line, but kernel
refused this name and said
devclass_alloc_unit: ed0 already exists, using next availale unit
number
Kernel used ed1 as device name and it did not match with config and
insert/remove lines. Fortunately, dhclient was called without args,
and it works, but if we wanted to use static IP address for PC-card,
it did not work.
This modification makes pccardd to execute insert/remove lines with
the true device name that returns from kernel. (Last change to
etc/pccard.conf.sample eliminated all hardwired device name from
insert/remove lines in /etc/pccard.conf)
Stop the recurring feeling of deja vu
Stop the recurring feeling of deja vu
Stop the recurring feeling of deja vu
and debounce the eject messages. We now mark the socket empty in the
interrupt handler, rather than after we've disabled the socket which
happens "much later".
probes are at the 'chip' level and will get overridden by pcic_p if it is
compiled in. It's still nice to get the better probe message if it's not...
Requested by: imp
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
the activate method to the setup_intr, and turn it off to
teardown_intr.
This makes the ed driver not enter its interrupt routine during the
probe. Apparently, an interrupt happens when you disable the
interrupts. There are other problems with ed still.
Should have no effect, but does make things a little cleaner. I
thought this was the race that was causing problems, but it turned out
to be in pccardd waking up after the empty/insert events had happened
and being confused.
Minor cleanup:
o Remove isahd from pccard_devinfo
o remove extra from controller
o formatting nits
o use PCCARD_DEVINFO(d) rather than a bare device_get_ivars(d)
as the unit argument instead of 0. disable_slot() calls
devclass_get_device() correctly, however because alloc_driver() does
it wrong, disable_slot() is unable to locate the child devices
attached to the pccard bus and thus fails to call device_delete_child()
on them. The end result is that when a card is removed, its detach
routine is never called, and re-insertion always fails.
With this fix (and the previous one to if_wi.c), I can now insert,
remove and re-insert my WaveLAN/IEEE card and things behave correctly.
kldunloading the if_wi.ko module also seems to work properly now.
Ok'ed by: imp
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
with the beep information it had (like ignoring it).
Submitted by: sanpei@sanpei.org (MIHIRA-san Yoshiro)
Add $FreeBSD$ to pccard_beep.c while I'm here.
problem.
o Create new timeout routine so we don't detach the card inside a ISR
but instead drop back to spl0 via a timeout of 0.
o Actually delete the child of the pccard device rather than just faking
it badly.
o Fix sio, ed and ep to have pccard detach routines that are int rather
than void.
o Fix ep and ed pccard detach routines to use if_detach rather than just
if_down. if_detach destroys the device, while if_down just marks it
down. In this incarnation of the pccard things, we map the disable
the slot action to detach the driver, which removes the driver from the
device tree. When that is done, a panic would soon follow as the
ifconfig tried to down the device.
Didn't fix:
o Should cache the pccard dev child's pointer in struct slot
o remove now unused parts of struct slot
o Any driver using softc after detach has been called. sio's softc used
to be statically allocated, so you could check sc->gone, but that is
now gone.
o Didn't remove gone from softc of drivers that use the old pccard method.
Didn't test:
o ed driver changes
o sio driver changes on pccards
o suspend (no laptop or apm support on my desktop)
o Gut the compatibility interface, you now must attach with newbus.
o Unit numbers from pccardd are now ignored. This may change the units
assigned to a card. It now uses the first available unit.
o kill old skeleton code that is now obsolete.
o Use newbus attachment code.
o cleanup interfile dependencies some.
o kill list of devices per slot. we use the device tree for what we need.
o Remove now obsolete code.
o The ep driver (and maybe ed) may need some config file tweaks to
allow it to attach. See config files that were committed for examples
on how to do this.
Drivers to be commited shortly.
This is an interrum fix until the new pccard. ed, ep and sio will be
supported by me with this release, although others are welcome to try
to support other devices before new pccard is working.
I plan on doing minimal further work on this code base. Be careful
when upgrading, since this code is known to work on my laptop and
those of a couple others as well, but your milage may vary.
BUGS TO BE FIXED:
o system memory isn't allocated yet, it will be soon.
o No devices actually have a pccard newbus attach in the tree.
BUGS THAT MIGHT BE FIXED:
o card removal, including suspend, usually hangs the system.
Many thanks to Peter Wemm and Doug Rabson for helping me to fill in
the missing bits of New Bus understanding at FreeBSD Con '99.
pc98 case that I missed before. Attempt to get the irq for the PCIC
first from the loader env var and second from the config system. I've
been able to boot my laptop with a kernel that hardwired the irq to
10. This should allow boot -c to finally start working for pcic irq,
but I've not tested that. Add $FreeBSD$ to slot.h.
floating before). Attach pccard devices to pcic, one per slot
(although this may change to one per pcic). pcic is now attached to
isa (to act as a bridge) and pccard is attached to pcic, cbb and
pc98ic (the last two are card bus bridge and the pc98ic version of
pcic, neither of which are in the tree yet). Move pccard compat code
into pccard/pccard_compat.c.
THIS REQUIRES A CONFIG FILE CHANGE. You must change your pcic/card
entries to be:
# PCCARD (PCMCIA) support
controller pcic0 at isa?
controller pcic1 at isa?
controller card0
The old system was upside down and this corrects that problem. It
will make it easier to add support for YENTA pccard/card bus bridges.
Much more cleanup needs to happen before newbus devices can have
pccard attachments. My previous commit's comments were premature.
devices. There may still be problems with said drivers, if so please
let me know.
o Move attach-like functionality to the nbk attach compatibility code.
o Smarter probe code: for the compatibility code probe succeeds if
strcmp succeeds, for noncompatibility you can do anything you like.
o Get rid of some compiler warnings introduced in last commit.
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
will allow newbus based drivers to have pccard attachments. Also
start printing out probe messages for pccards stating the resources
used and regularize many of the pccard printfs.
Reviewed by: Peter Wemm.
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
o Add field to dev_desc for the size of the io port range. This isn't
used yet in the committed sources, but will make the transition easier
in the future.
If you build this into your kernel, you will need to rebuild pccardd.
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
