with more than one read(). When we detect one, don't
forget to pass it to async_Input() and drop our
terminal back into command mode.
Don't output an extraneous \r if we're passed \r\n
to prompt_vprintf in raw mode.
when recalculating the ip checksum. cp is not guaranteed to
be aligned. It now doesn't matter that cp isn't aligned as
the caller does another mbuf_Alloc() regardless.
need to process a signal (usually a SIGALRM). Check to see
if we need to process a signal both before *and* after calling
select() as older (pre-2.0) versions of ppp used to.
This handles the possibility that ppp may block at some
point (maybe due to an open() of a misconfigured device).
Previously, we'd potentially lock up in select().
The `necessary' marker reduces the increased signal checking
overhead so that at full speed with no compression transferring
an 83Mb file via a ``!ppp -direct'' device, we get a 1%
throughput gain.
ACCMAP being REQuested by the peer, also increment our FSM
id so that we don't end up sending out a new REQ with the
same ID and different data (the changed ACCMAP).
orthogonal to the other entries).
Clean up X selection code a bit.
Choose proper architecture subdirectories on mirror sites now that we've
gone fully to the new multi-arch directory scheme.
The old VN device broke in -4.x when the definition of B_PAGING
changed. This patch fixes this plus implements additional capabilities.
The new VN device can be backed by a file ( as per normal ), or it can
be directly backed by swap.
Due to dependencies in VM include files (on opt_xxx options) the new
vn device cannot be a module yet. This will be fixed in a later commit.
This commit delimitted by tags {PRE,POST}_MATT_VNDEV
before printing it. Terminate when we come to a 0xff byte. This
allows there to be zero or more additional info fields printed
correctly. Before, the old code would print bogons or dump core when
presented with this case.
I don't know what the spec says about this, exactly, but this allows
me to do a dumpcis of my non-ATA AMP 4M FLASH cards w/o pccardc
dumping core.
when we've simply missed a packet.
When our Predictor1 CRC is wrong (implying we've dropped
a packet), don't send a ResetReq(). Instead, send another
CCP ConfigReq(). *shrug* My tests show this as being far
worse than the ResetReq as we may have further Nak/Rejs etc
and we're basically resetting both our incoming and outgoing
compression dictionaries, but rfc1978 says the ConfigReq is
correct, so we'd better go along...
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Move the Olicom token ring driver to the officially sanctionned location of
/sys/contrib. Also fix some brokenness in the generic token ring support.
Be warned that if_dl.h has been changed and SOME programs might
like recompilation.
