and start teaching subsystems about it.
The Atheros MIPS platforms don't guarantee any kind of FIFO consistency
with interrupts in hardware. So software needs to do a flush when it
receives an interrupt and before it calls the interrupt handler.
There are new ones for the QCA934x and QCA955x, so do a few things:
* Get rid of the individual ones (for ethernet and IP2);
* Create a mux and enum listing all the variations on DDR flushes;
* replace the uses of IP2 with the relevant one (which will typically
be "PCI" here);
* call the USB DDR flush before calling the real USB interrupt handlers;
* call the ethernet one upon receiving an interrupt that's for us,
rather than never calling it during operation.
Tested:
* QCA9558 (TP-Link archer c7 v2)
* AR9331 (Carambola 2)
TODO:
* PCI, USB, ethernet, etc need to do a double-check to see if the
interrupt was truely for them before doing the DDR. For now I
prefer "correct" over "fast".
This stops the panics that occur on MIPS platforms when doing say,
'sysctl dev.ath.0' whilst the MAC is asleep. The MIPS platform is
rather unforgiving in getting power-save register access wrong and you
will get all kinds of odd failures if you don't have things woken
up at the right times.
Tested:
* QCA9558 (TP-Link Archer C7 v2)
* AR9331 (Carambola 2)
.. with no VAPs configured and ath0 down (thus the MAC is definitely
asleep.)
PR: kern/201117
the kernel would generate a bogus one with a ":/<path>" suffix.
This would only occur for the case where there was no explicit
"principal" argument and the getaddrinfo() call in mount_nfs.c failed to a
return a cannonical name for the server.
This patch fixes this unusual case.
PR: 201073
Submitted by: masato@itc.naist.jp
MFC after: 2 weeks
Update setkey and libipsec to understand aes-gcm-16 as an
encryption method.
A partial commit of the work in review D2936.
Submitted by: eri
Reviewed by: jmg
MFC after: 2 weeks
Sponsored by: Rubicon Communications (Netgate)
change to GMAC easier on A20 SoCs.
On A10 only the EMAC controller is available (fast ethernet), but on A20
there is also GMAC a high (or better) performant controller (gigabit
ethernet).
On A20 the both controllers uses the same pins to talk to the ethernet PHY
(MII or RGMII) and they can be selected by the GPIO pin mux.
There is work in progress to bring in GMAC support.
When IPSEC is enabled on the kernel the forwarding path has an optimization to not enter the code paths
for checking security policies but first checks if there is any security policy active at all.
The patch introduces the same optimization but for traffic generated from the host itself.
This reduces the overhead by 50% on my tests for generated host traffic without and SP active.
Differential Revision: https://reviews.freebsd.org/D2980
Reviewed by: ae, gnn
Approved by: gnn(mentor)
The Allwinner SoC has an AHCI device on its internal main bus rather
than the PCI bus. This SoC is somewhat underdocumented, and its SATA
controller is no exception. The methods to support this chip were
harvested from the Linux Allwinner SDK, and then constants invented to
describe what's going on based on low-level constants contained in the
SATA standard and guess work.
This SoC requires a specific AHCI channel setup in order to start the
operations on the channel properly.
Clock setup and AHCI channel setup idea came from NetBSD.
Tested on Cubieboard 2 and Banana pi (and attachment on Cubieboard by
Pratik Singhal).
Differential Revision: https://reviews.freebsd.org/D737
Submitted by: imp
Reviewed by: imp, ganbold, mav, andrew
Try to preserve the xn configuration when migrating. This is not always
possible since the backend might not have the same set of options
available, in which case we will try to preserve as many as possible.
MFC after: 2 weeks
PR: 183139
Reported by: mcdouga9@egr.msu.edu
Sponsored by: Citrix Systems R&D
kmalloc() call. Make function global instead of static inline to fix
compiler warnings about passing variable argument lists to inline
functions.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The SoC, the flash, the ethernet ports and ethernet switch all work.
The USB works.
The 11ac PCIe NIC internally is at least seen by the PCIE RC, but
I haven't tried using it yet. There's no driver and I haven't
yet swapped it out for a non-11ac chip.
The on-chip 2GHz wifi works, but there are some data errors that
get thrown up in STA mode when scanning. I have a feeling I have
to finish the DDR flush code out and have it run correctly on the
shared interrupts; that'll take a bit of time to get right.
But if you're after an updated piece of hardware, the Archer C7 v2
is certainly there, and you can replace the 11ac NIC with a 3x3
Atheros PCIe device (eg AR9380, AR9390, AR9580, etc) and it'll
"just work".
Tested:
* TP-Link archer c7v2.
The Tp-link Archer-C7v2 unit has a QCA9558 internally but hangs the
QCA988x 11ac PCIe NIC off of PCI RC #1, not #0.
So I actually finally /do/ have a board to verify whether PCIe is working.
Grr.
Tested:
* TP-Link Archer-C7v2.
lightly used. Find the proper .m file when we depend on *_if.[ch] in
the srcs line, with seat-belts for false positive matches. This uses
make's path mechanism. A further refinement would be to calculate this
once, and then pass the resulting _MPATH to modules submakes.
Differential Revision: https://reviews.freebsd.org/D2327
compared to the old NFS client via email to the freebsd-fs@ mailing list.
For the new client, when multiple clients attempted to create a symbolic
link concurrently, more that one client would report success instead of
EEXIST. This was caused by code in the new client that mapped EEXIST to
OK assuming it was caused by a retried RPC request.
Since the old client did not do this, the patch defaults to the old
behaviour and permits the new behaviour to be enabled via a sysctl.
Reported by: alex.burlyga.ietf@gmail.com
Tested by: alex.burlyga.ietf@gmail.com
MFC after: 2 weeks
ip_forward() does a route lookup for testing this packet can be sent to a known destination,
it also can do another route lookup if it detects that an ICMP redirect is needed,
it forgets all of this and handovers to ip_output() to do the same lookup yet again.
This optimisation just does one route lookup during the forwarding path and handovers that to be considered by ip_output().
Differential Revision: https://reviews.freebsd.org/D2964
Approved by: ae, gnn(mentor)
MFC after: 1 week
user address when ABI uses shared page.
Note that the change is no-op for correctness, since shared page does
not fault. The mapping for the shared page is installed at the
address space creation, the page is unmanaged and its pte/pv entry
cannot be reclaimed.
Submitted by: Oliver Pinter
Review: https://reviews.freebsd.org/D2954
MFC after: 1 week
macros on amd64 and i386. Move the definition to machine/param.h.
kgdb defines INKERNEL() too, the conflict is resolved by renaming kgdb
version to PINKERNEL().
On i386, correct the lowest kernel address. After the shared page was
introduced, USRSTACK no longer points to the last user address + 1 [*]
Submitted by: Oliver Pinter [*]
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
asserts are made. Remove them, since we might dereference freed
memory. Leaked locks are asserted by the syscall return code anyway.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
We now take z_teardown_lock as a writer to ensure that there is no I/O
while the filesystem state is in a flux. Also, zfs_suspend_fs() ->
zfsvfs_teardown() call zfs_unregister_callbacks() and zfs_resume_fs() ->
zfsvfs_setup() call zfs_unregister_callbacks(). Previously there was no
synchronization between those calls and the calls in the re-mounting
case. That could lead to concurrent execution and a crash.
PR: 180060
Differential Revision: https://reviews.freebsd.org/D2865
Suggested by: mahrens
Reviewed by: delphij, pho, mahrens, will
MFC after: 13 days
Sponsored by: ClusterHQ
According to report, some recent unrelated changes in the driver triggered
timeouts when testing for absent port multiplier. Cause of this behavior
channge is unclear, but since these chips are old, rare and buggy, it is
easier to just disable port multiplier support, same as done in Linux.
Reported by: bar
MFC after: 3 days
DMA handles all data transfers up to 128K or 16 segments and fallback to
pio mode when DMA requirements are not met.
The read performance has improved greatly while the write performance also
showed some improvement but seems limited by the card type and quality.
Submitted by: Pratik Singhal <pratiksinghal@freebsd.org>
Sponsored by: Google Summer of Code 2015
Tested on: A10 (cubieboard) and A20 (cubieboard 2 and banana pi)
them when a different thread last used them, or when the thread was last
run on a different cpu.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
process beyond the end of the process address space. Such setting is
not dangerous to the kernel integrity, but it causes confusing
application misbehaviour.
Sponsored by: The FreeBSD Foundation
MFC after: 12 days
