when the user has indicated that the system has synchronized TSCs or it has
P-state invariant TSCs. For the former case, we may clear the tunable if it
fails the test to prevent accidental foot-shooting. For the latter case, we
may set it if it passes the test to notify the user that it may be usable.
This also introduces a new detection path for family 10h and newer
pre-bulldozer cpus, pre-10h hardware should not be affected.
Tested by: Gary Jennejohn <gljennjohn@googlemail.com>
(with pre-10h hardware)
MFC after: 2 weeks
driver would verify that requests for child devices were confined to any
existing I/O windows, but the driver relied on the firmware to initialize
the windows and would never grow the windows for new requests. Now the
driver actively manages the I/O windows.
This is implemented by allocating a bus resource for each I/O window from
the parent PCI bus and suballocating that resource to child devices. The
suballocations are managed by creating an rman for each I/O window. The
suballocated resources are mapped by passing the bus_activate_resource()
call up to the parent PCI bus. Windows are grown when needed by using
bus_adjust_resource() to adjust the resource allocated from the parent PCI
bus. If the adjust request succeeds, the window is adjusted and the
suballocation request for the child device is retried.
When growing a window, the rman_first_free_region() and
rman_last_free_region() routines are used to determine if the front or
end of the existing I/O window is free. From using that, the smallest
ranges that need to be added to either the front or back of the window
are computed. The driver will first try to grow the window in whichever
direction requires the smallest growth first followed by the other
direction if that fails.
Subtractive bridges will first attempt to satisfy requests for child
resources from I/O windows (including attempts to grow the windows). If
that fails, the request is passed up to the parent PCI bus directly
however.
The PCI-PCI bridge driver will try to use firmware-assigned ranges for
child BARs first and only allocate a "fresh" range if that specific range
cannot be accommodated in the I/O window. This allows systems where the
firmware assigns resources during boot but later wipes the I/O windows
(some ACPI BIOSen are known to do this) to "rediscover" the original I/O
window ranges.
The ACPI Host-PCI bridge driver has been adjusted to correctly honor
hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge
makes a wildcard request for an I/O window range.
The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option
is enabled. This is a transition aide to allow platforms that do not
yet support bus_activate_resource() and bus_adjust_resource() in their
Host-PCI bridge drivers (and possibly other drivers as needed) to use the
old driver for now. Once all platforms support the new driver, the
kernel option and old driver will be removed.
PR: kern/143874 kern/149306
Tested by: mav
disk dumping.
With the option SW_WATCHDOG on, these operations are doomed to let
watchdog fire, fi they take too long.
I implemented the stubs this way because I really want wdog_kern_*
KPI to not be dependant by SW_WATCHDOG being on (and really, the option
only enables watchdog activation in hardclock) and also avoid to
call them when not necessary (avoiding not-volountary watchdog
activations).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, des
MFC after: 2 weeks
NFS client (which I guess is no longer experimental). The fstype "newnfs"
is now "nfs" and the regular/old NFS client is now fstype "oldnfs".
Although mounts via fstype "nfs" will usually work without userland
changes, an updated mount_nfs(8) binary is needed for kernels built with
"options NFSCL" but not "options NFSCLIENT". Updated mount_nfs(8) and
mount(8) binaries are needed to do mounts for fstype "oldnfs".
The GENERIC kernel configs have been changed to use options
NFSCL and NFSD (the new client and server) instead of NFSCLIENT and NFSSERVER.
For kernels being used on diskless NFS root systems, "options NFSCL"
must be in the kernel config.
Discussed on freebsd-fs@.
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
counting memory being dumped in 16MB increments is somewhat silly.
Especially if the dump fails and everything you've got for debugging
is screen filled with numbers in 16 decrements... Replace that with
percentage-based progress with max 10 updates all fitting into one
line.
Collapse other very "useful" piece of crash information (total ram) into
the same line to save some more space.
MFC after: 1 week
set the f_flags field of "struct statfs". This had the interesting
effect of making the NFSv4 mounts "disappear" after r221014,
since NFSMNT_NFSV4 and MNT_IGNORE became the same bit.
Move the files used for a diskless NFS root from sys/nfsclient
to sys/nfs in preparation for them to be used by both NFS
clients. Also, move the declaration of the three global data
structures from sys/nfsclient/nfs_vfsops.c to sys/nfs/nfs_diskless.c
so that they are defined when either client uses them.
Reviewed by: jhb
MFC after: 2 weeks
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
Add pmap_invalidate_cache_pages() method on x86. It flushes the CPU
cache for the set of pages, which are not neccessary mapped. Since its
supposed use is to prepare the move of the pages ownership to a device
that does not snoop all CPU accesses to the main memory (read GPU in
GMCH), do not rely on CPU self-snoop feature.
amd64 implementation takes advantage of the direct map. On i386,
extract the helper pmap_flush_page() from pmap_page_set_memattr(), and
use it to make a temporary mapping of the flushed page.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
32 bits. Some times compiler inserts unnecessary instructions to preserve
unused upper 32 bits even when it is casted to a 32-bit value. It reduces
such compiler mistakes where every cycle counts.
MPERF MSRs are available. It was disabled in r216443. Remove the earlier
hack to subtract 0.5% from the calibrated frequency as DELAY(9) is little
bit more reliable now.
update_gdt_{f,g}sbase. The functions set the flag when td == curthread,
and sysarch is always called with curthread.
Reviewed by: jhb, jkim
MFC after: 1 week
Thread might be preempted after testing, which causes the flag to be
cleared. If ast was not delivered, we will do sysret with potentially
wrong fs/gs bases.
Reviewed by: jhb, jkim
MFC after: 1 week (together with r220430, r220452)
return. The ast() function may cause a context switch in which case
PCB_FULL_IRET would be set in the pcb. However, the code was not
rechecking the flag after ast() returned and would not properly restore
the FSBASE and GSBASE MSRs. To fix, recheck the PCB_FULL_IRET flag after
ast() returns.
While here, trim an instruction (and memory access) from the doreti path
and fix a typo in a comment.
MFC after: 1 week
safer for i386 because it can be easily over 4 GHz now. More worse, it can
be easily changed by user with 'machdep.tsc_freq' tunable (directly) or
cpufreq(4) (indirectly). Note it is intentionally not used in performance
critical paths to avoid performance regression (but we should, in theory).
Alternatively, we may add "virtual TSC" with lower frequency if maximum
frequency overflows 32 bits (and ignore possible incoherency as we do now).
path via the sysretq instruction to return from the system call. This was
removed in 190620 and not quite fully restored in 195486. This resolves
most of the performance regression in system call microbenchmarks between
7 and 8 on amd64.
Reviewed by: kib
MFC after: 1 week
In particular:
- implement compat shims for old stat(2) variants and ogetdirentries(2);
- implement delivery of signals with ancient stack frame layout and
corresponding sigreturn(2);
- implement old getpagesize(2);
- provide a user-mode trampoline and LDT call gate for lcall $7,$0;
- port a.out image activator and connect it to the build as a module
on amd64.
The changes are hidden under COMPAT_43.
MFC after: 1 month
I have not properly thought through the commit. After r220031 (linux
compat: improve and fix sendmsg/recvmsg compatibility) the basic
handling for SO_PASSCRED is not sufficient as it breaks recvmsg
functionality for SCM_CREDS messages because now we would need to handle
sockcred data in addition to cmsgcred. And that is not implemented yet.
Pointyhat to: avg
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
and per-loginclass resource accounting information, to be used by the new
resource limits code. It's connected to the build, but the code that
actually calls the new functions will come later.
Sponsored by: The FreeBSD Foundation
Reviewed by: kib (earlier version)
instead of 0x100000. As a side effect, an amd64 kernel now loads at
physical address 0x200000 instead of 0x100000. This is probably for the
best because it avoids the use of a 2MB page mapping for the first 1MB of
the kernel that also spans the fixed MTRRs. However, getmemsize() still
thinks that the kernel loads at 0x100000, and so the physical memory between
0x100000 and 0x200000 is lost. Fix this problem by replacing the hard-wired
constant in getmemsize() by a symbol "kernphys" that is defined by the
linker script.
In collaboration with: kib
This seems to have been a part of a bigger patch by dchagin that either
haven't been committed or committed partially.
Submitted by: dchagin, nox
MFC after: 2 weeks
And drop dummy definitions for those system calls.
This may transiently break the build.
PR: kern/149168
Submitted by: John Wehle <john@feith.com>
Reviewed by: netchild
MFC after: 2 weeks
Since signal trampolines are copied to the shared page do not need to
leave place on the stack for it. Forgotten in the previous commit.
MFC after: 1 Week
CPUs. These CPUs need explicit MSR configuration to expose ceratin CPU
capabilities (e.g., CMPXCHG8B) to work around compatibility issues with
ancient software. Unfortunately, Rise mP6 does not set the CX8 bit in CPUID
and there is no MSR to expose the feature although all mP6 processors are
capable of CMPXCHG8B according to datasheets I found from the Net. Clean up
and simplify VIA PadLock detection while I am in the neighborhood.
configurations and make it opt-in for those who want it. LINT will
still build it.
While it may be a perfect win in some scenarios, it still troubles users
(see PRs) in general cases. In addition we are still allocating resources
even if disabled by sysctl and still leak arp/nd6 entries in case of
interface destruction.
Discussed with: qingli (2010-11-24, just never executed)
Discussed with: juli (OCTEON1)
PR: kern/148018, kern/155604, kern/144917, kern/146792
MFC after: 2 weeks
