While the PV SCSI SG list can handle 512k of SG entries, it can only do
so for I/O that's aligned to 4k or better. newfs_msdos does unaligned
I/O, so triggers too long for host errors in cam when a 512k I/O is
attempted. Prefer power of 2 256k to the absolute maximum 508k, though
that can be revisited should the latter show to give significant
performance improvement.
MFC After: 3 days
Tested by: darius on discord (508k version of patch)
Sponsored by: Netflix
Doing a 'dd' over iscsi will reliably cause stalls. Tx
cleaning _should_ reliably happen as data is sent.
However, currently if the transmit queue fills it will
wait until the iflib timer (hz/2) runs.
This change causes the the tx taskq thread to be run
if there are completed descriptors.
While here:
- make timer interrupt delay a sysctl
- simplify txd_db_check handling
- comment on INTR types
Background on the change:
Initially doorbell updates were minimized by only writing to the register
on every fourth packet. If txq_drain would return without writing to the
doorbell it scheduled a callout on the next tick to do the doorbell write
to ensure that the write otherwise happened "soon". At that time a sysctl
was added for users to avoid the potential added latency by simply writing
to the doorbell register on every packet. This worked perfectly well for
e1000 and ixgbe ... and appeared to work well on ixl. However, as it
turned out there was a race to this approach that would lockup the ixl MAC.
It was possible for a lower producer index to be written after a higher one.
On e1000 and ixgbe this was harmless - on ixl it was fatal. My initial
response was to add a lock around doorbell writes - fixing the problem but
adding an unacceptable amount of lock contention.
The next iteration was to use transmit interrupts to drive delayed doorbell
writes. If there were no packets in the queue all doorbell writes would be
immediate as the queue started to fill up we could delay doorbell writes
further and further. At the start of drain if we've cleaned any packets we
know we've moved the state machine along and we write the doorbell (an
obvious missing optimization was to skip that doorbell write if db_pending
is zero). This change required that tx interrupts be scheduled periodically
as opposed to just when the hardware txq was full. However, that just leads
to our next problem.
Initially dedicated msix vectors were used for both tx and rx. However, it
was often possible to use up all available vectors before we set up all the
queues we wanted. By having rx and tx share a vector for a given queue we
could halve the number of vectors used by a given configuration. The problem
here is that with this change only e1000 passed the necessary value to have
the fast interrupt drive tx when appropriate.
Reported by: mav@
Tested by: mav@
Reviewed by: gallatin@
MFC after: 1 month
Sponsored by: iXsystems
Differential Revision: https://reviews.freebsd.org/D27683
The pidx argument of isc_rxd_flush() indicates which is the last valid
receive descriptor to be used by the NIC. However, current code has
multiple issues:
- Intel drivers write pidx to their RDT register, which means that
NICs will only use the descriptors up to pidx-1 (modulo ring size N),
and won't actually use the one pointed by pidx. This does not break
reception, but it is anyway confusing and suboptimal (the NIC will
actually see only N-2 descriptors as available, rather than N-1).
Other drivers (if_vmx, if_bnxt, if_mgb) adhere to this semantic).
- The semantic used by Intel (RDT is one descriptor past the last
valid one) is used by most (if not all) NICs, and it is also used
on the TX side (also in iflib). Since iflib is not currently
using this semantic for RX, it must decrement fl->ifl_pidx
(modulo N) before calling isc_rxd_flush(), and then the
per-driver callback implementation must increment the index
again (to match the real semantic). This is confusing and suboptimal.
- The iflib refill function is also called at initialization.
However, in case the ring size is smaller than 128 (e.g. if_mgb),
the refill function will actually prepare all the receive
descriptors (N), without leaving one unused, as most of NICs assume
(e.g. to avoid RDT to overrun RDH). I can speculate that the code
looks like this right now because this issue showed up during
testing (e.g. with if_mgb), and it was easy to workaround by
decrementing pidx before isc_rxd_flush().
The goal of this change is to simplify the code (removing a bunch
of instructions from the RX fast path), and to make the semantic of
isc_rxd_flush() consistent across drivers. To achieve this, we:
- change the semantics of the pidx argument to the usual one (that
is the index one past the last valid one), so that both iflib and
drivers avoid the decrement/increment dance.
- fix the initialization code to prepare at most N-1 descriptors.
Reviewed by: markj
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D26191
When vmx(4) was converted to an iflib driver in r343291, the
power-of-2 queue count constraint was removed as it appeared that
current implementations of the VMXNET3 virtual device no longer
required that constraint. It turns out that some of the
implementations still do, and on such systems, the device will fail to
initialize when configured with a non-power-of-2 RX or TX queue count.
PR: 237321
Reported by: ncrogers@gmail.com
MFC after: 1 week
These adjustments improve performance with jumbo frames and/or LRO
enabled (i.e., when there may be multiple descriptors per packet) by
increasing the default size of the receive queues and by always using
page-sized buffers for the body type receive ring.
This patch also adjust the initialization of the max frame size to
remove cases where certain configuration sequences would result in 2K
receive buffers being used instead of 4K ones when jumbo frames were
enabled.
Reviewed by: gallatin
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D23950
This fixes a bug where the checksum offload status of received packets
was being taken from the first descriptor instead of the last, which
affected LRO packets.
The driver has been hardened against the device skipping receive
descriptors, although it is not believed that this can occur given the
way this implementation configures the receive rings.
Additionally, for packets received with the error indicator set, the
driver now forces the length of all fragments in that packet to zero
prior to passing it to iflib. Such packets should wind up being
discarded at some point in the stack anyway, but this removes any
questions by killing them in the driver.
Counters have been added (and exposed via sysctls) for skipped receive
descriptors, zero-length packets received, and packets received with
the error indicator set so that these conditions can be easily
observed in the field.
PR: 243126, 243392, 240628
Reported by: avg, alexandr.oleynikov@gmail.com, Harald Schmalzbauer
Reviewed by: gallatin
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D23949
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
We observe at least one problem: if a UDP socket is connect(2)-ed, then a
received packet that matches the connection cannot be matched to the
corresponding PCB because of an incorrect flow ID. That was oberved for DNS
requests from the libc resolver. We got this problem because FreeBSD
r343291 enabled code that can set rsstype of received packets to values
other than M_HASHTYPE_OPAQUE_HASH. Earlier that code was under 'ifdef
notyet'.
The essence of this change is to use the system-wide RSS key instead of
some historic hardcoded key when the software RSS is enabled and it is
configured to use Toeplitz algorithm (the default).
In all other cases, the driver reports the opaque hash type for received
packets while still using Toeplitz algorithm with the internal key.
PR: 242890
Reviewed by: pkelsey
Sponsored by: Panzura
Differential Revision: https://reviews.freebsd.org/D23147
Fix a mistake introduced by r343291, which ported the vmx(4)
driver to iflib.
In case of TSO, the hlen field of the (first) tx descriptor must
be initialized to the cumulative length of Ethernet, IP and TCP
headers. The length of the TCP header was missing.
PR: 236999
Reported by: pkelsey
Reviewed by: avg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D22967
This driver allows to usage of the paravirt SCSI controller
in VMware products like ESXi. The pvscsi driver provides a
substantial performance improvement in block devices versus
the emulated mpt and mps SCSI/SAS controllers.
Error handling in this driver has not been extensively tested
yet.
Submitted by: vbhakta@vmware.com
Relnotes: yes
Sponsored by: VMware, Panzura
Differential Revision: D18613
As of r347221 the iflib legacy interrupt mode setup assumes that drivers
perform both receive and transmit processing from the interrupt handler.
This assumption is invalid in the vmxnet3 driver, so introduce the
IFLIB_SINGLE_IRQ_RX_ONLY flag to make iflib avoid tx processing in the
interrupt handler.
PR: 239118
Reported and tested by: Juraj Lutter <otis@sk.freebsd.org>
Obtained from: marius
Reviewed by: gallatin
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D21831
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
When in MSI mode, the device was only being configured with one
interrupt index, but it needs two - one for the actual interrupt and
one to park the tx queue at.
Also clarified comments relating to interrupt index assignment.
Reported by: Yuri Pankov <yuripv@yuripv.net>
MFC after: 1 day
bus_teardown_intr(9) before pci_release_msi(9).
- Ensure that iflib(4) and associated drivers pass correct RIDs to
bus_release_resource(9) by obtaining the RIDs via rman_get_rid(9)
on the corresponding resources instead of using the RIDs initially
passed to bus_alloc_resource_any(9) as the latter function may
change those RIDs. Solely em(4) for the ioport resource (but not
others) and bnxt(4) were using the correct RIDs by caching the ones
returned by bus_alloc_resource_any(9).
- Change the logic of iflib_msix_init() around to only map the MSI-X
BAR if MSI-X is actually supported, i. e. pci_msix_count(9) returns
> 0. Otherwise the "Unable to map MSIX table " message triggers for
devices that simply don't support MSI-X and the user may think that
something is wrong while in fact everything works as expected.
- Put some (mostly redundant) debug messages emitted by iflib(4)
and em(4) during attachment under bootverbose. The non-verbose
output of em(4) seen during attachment now is close to the one
prior to the conversion to iflib(4).
- Replace various variants of spelling "MSI-X" (several in messages)
with "MSI-X" as used in the PCI specifications.
- Remove some trailing whitespace from messages emitted by iflib(4)
and change them to consistently start with uppercase.
- Remove some obsolete comments about releasing interrupts from
drivers and correct a few others.
Reviewed by: erj, Jacob Keller, shurd
Differential Revision: https://reviews.freebsd.org/D18980
Also, expose IFLIB_MAX_RX_SEGS to iflib drivers and add
iflib_dma_alloc_align() to the iflib API.
Performance is generally better with the tunable/sysctl
dev.vmx.<index>.iflib.tx_abdicate=1.
Reviewed by: shurd
MFC after: 1 week
Relnotes: yes
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D18761
and VMware legal:
- Add a dual BSD-2 Clause/GPLv2 LICENSE file in the VMCI directory
- Remove the use of "All Rights Reserved"
- Per best practice, remove copyright/license info from Makefile
Reviewed by: imp, emaste, jhb, Vishnu Dasa <vdasa@vmware.com>
Approved by: VMware legal via Mark Peek <markpeek@vmware.com>
Differential Revision: https://reviews.freebsd.org/D14979
To fix the GCC build, remove multiple redundant declarations of
vmci_send_datagram() (the copy in vmci.h as well as the extern definition in
vmci_queue_pair.c were wholly redundant).
Also to fix the GCC build, include a non-empty format string in the vmci(4)
definition of ASSERT(). It seems harmless either way, but adding the
stringified invariant is easier than masking the warning.
The other vmci_kernel_defs.h changes are cosmetic and simply match macros to
existing definitions.
Reported by: GCC 6.4.0
Sponsored by: Dell EMC Isilon
In a virtual machine, VMCI is exposed as a regular PCI device. The primary
communication mechanisms supported are a point-to-point bidirectional
transport based on a pair of memory-mapped queues, and asynchronous
notifications in the form of datagrams and doorbells. These features are
available to kernel level components such as vSockets through the VMCI
kernel API. In addition to this, the VMCI kernel API provides support for
receiving events related to the state of the VMCI communication channels,
and the virtual machine itself.
Submitted by: Vishnu Dasa <vdasa@vmware.com>
Reviewed by: bcr, imp
Obtained from: VMware
Differential Revision: https://reviews.freebsd.org/D14289
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Focus on code where we are doing multiplications within malloc(9). None of
these is likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
The crash can occur when all of the following conditions are true:
- a packet consists of multiple segements (requires LRO enabled)
- there has been a failure to allocate an mbuf for the packet and
the packet has to be dropped
- a host (vmware) still owned at least one segment of the packet,
so the driver had to wait for another interrupt to proceed to
discarding the remaning segment(s)
Reviewed by: rstone
MFC after: 2 weeks
Sponsored by: Panzura
Differential Revision: https://reviews.freebsd.org/D10874
In particular for me this fixes checksum problem when if_bridge attached
to the interface requests TXCSUM to be disabled, but effectively ignored.
MFC after: 3 days
Sponsored by: iXsystems, Inc.
Using other values causes VMXNET3_CMD_ENABLE to fail. The Linux
driver also enforces this restriction.
Reviewed by: bryanv
MFC after: 1 week
Sponsored by: Norse
Differential Revision: https://reviews.freebsd.org/D4139
from the FreeBSD network code. The flag is still kept around in the
"sys/mbuf.h" header file, but does no longer have any users. Instead
the "m_pkthdr.rsstype" field in the mbuf structure is now used to
decide the meaning of the "m_pkthdr.flowid" field. To modify the
"m_pkthdr.rsstype" field please use the existing "M_HASHTYPE_XXX"
macros as defined in the "sys/mbuf.h" header file.
This patch introduces new behaviour in the transmit direction.
Previously network drivers checked if "M_FLOWID" was set in "m_flags"
before using the "m_pkthdr.flowid" field. This check has now now been
replaced by checking if "M_HASHTYPE_GET(m)" is different from
"M_HASHTYPE_NONE". In the future more hashtypes will be added, for
example hashtypes for hardware dedicated flows.
"M_HASHTYPE_OPAQUE" indicates that the "m_pkthdr.flowid" value is
valid and has no particular type. This change removes the need for an
"if" statement in TCP transmit code checking for the presence of a
valid flowid value. The "if" statement mentioned above is now a direct
variable assignment which is then later checked by the respective
network drivers like before.
Additional notes:
- The SCTP code changes will be committed as a separate patch.
- Removal of the "M_FLOWID" flag will also be done separately.
- The FreeBSD version has been bumped.
MFC after: 1 month
Sponsored by: Mellanox Technologies
The current TSO limitation feature only takes the total number of
bytes in an mbuf chain into account and does not limit by the number
of mbufs in a chain. Some kinds of hardware is limited by two
factors. One is the fragment length and the second is the fragment
count. Both of these limits need to be taken into account when doing
TSO. Else some kinds of hardware might have to drop completely valid
mbuf chains because they cannot loaded into the given hardware's DMA
engine. The new way of doing TSO limitation has been made backwards
compatible as input from other FreeBSD developers and will use
defaults for values not set.
Reviewed by: adrian, rmacklem
Sponsored by: Mellanox Technologies
MFC after: 1 week
The current TSO limitation feature only takes the total number of
bytes in an mbuf chain into account and does not limit by the number
of mbufs in a chain. Some kinds of hardware is limited by two
factors. One is the fragment length and the second is the fragment
count. Both of these limits need to be taken into account when doing
TSO. Else some kinds of hardware might have to drop completely valid
mbuf chains because they cannot loaded into the given hardware's DMA
engine. The new way of doing TSO limitation has been made backwards
compatible as input from other FreeBSD developers and will use
defaults for values not set.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Assume the number of description used is reasonable value to
increment this otherwise opaque field by.
While here, reduce a minor difference between the legacy and
multiqueue transmit paths.
MFC after: 1 week
This requires the VMware vmxnet3 device to flip the start of packet
descriptor's generation before the rest of the packet's descriptors
have been loaded into the Rx ring. I've never observed this behavior,
and it seems to make the most sense not to do it this way. But it is
not a lot of work for the driver to handle this situation just in case.
MFC after: 1 week
Apparently for VMware Fusion (and presumably VMware Workstation/Player
since the PR states TSO is broken there too, but I cannot test), the
TCP header pseudo checksum calculated should only include the protocol
(IPPROTO_TCP) value, not also the lengths as the stack does instead.
VMware ESXi seems to ignore whatever value is in the TCP header checksum,
and it is a bit surprising there is a different behavior between the
VMware products. And it is unfortunate that on ESXi we are forced to do
this extra bit of work.
PR: kern/185849
MFC after: 3 days
As a prerequisite for multiple queues, the guest must have MSIX enabled.
Unfortunately, to work around device passthrough bugs, FreeBSD disables
MSIX when running as a VMWare guest due to the hw.pci.honor_msi_blacklist
tunable; this tunable must be disabled for multiple queues.
Also included is various minor changes from the projects/vmxnet branch.
MFC after: 1 month
interface, in the r241616 a crutch was provided. It didn't work well, and
finally we decided that it is time to break ABI and simply make if_baudrate
a 64-bit value. Meanwhile, the entire struct if_data was reviewed.
o Remove the if_baudrate_pf crutch.
o Make all fields of struct if_data fixed machine independent size. The
notion of data (packet counters, etc) are by no means MD. And it is a
bug that on amd64 we've got a 64-bit counters, while on i386 32-bit,
which at modern speeds overflow within a second.
This also removes quite a lot of COMPAT_FREEBSD32 code.
o Give 16 bit for the ifi_datalen field. This field was provided to
make future changes to if_data less ABI breaking. Unfortunately the
8 bit size of it had effectively limited sizeof if_data to 256 bytes.
o Give 32 bits to ifi_mtu and ifi_metric.
o Give 64 bits to the rest of fields, since they are counters.
__FreeBSD_version bumped.
Discussed with: emax
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
