The device reports support for SATA Asynchronous Notification in its
IDENTIFY data, but returns error on attempt to enable that feature.
Make SATA XPT of CAM only report these errors, but not fail the device.
MFC after: 1 week
Element Descriptor page if it is not supported. This removes one error
message from verbose logs during boot on systems with some enclosures.
Sponsored by: iXsystems, Inc.
safe in some cases to reduce CCB priority after it was scheduled with high
priority. This fixes reproducible deadlock when command sent through the
pass interface while ATA XPT recovers from command timeout.
Instead of that enforce priority at passioctl(). libcam provides no obvious
interface to specify CCB priority and so much (all?) code specifies zero
(highest) priority. This change limits pass CCBs priority to NORMAL run
level, allowing XPT to complete bus and device recovery after reset before
running any payload.
In particular, do not lock Giant conditionally when calling into the
filesystem module, remove the VFS_LOCK_GIANT() and related
macros. Stop handling buffers belonging to non-mpsafe filesystems.
The VFS_VERSION is bumped to indicate the interface change which does
not result in the interface signatures changes.
Conducted and reviewed by: attilio
Tested by: pho
System time is set later on boot process then initial bus scan by CAM.
Until that moment microtime() is equal to microuptime(), and if system
boots quickly, the value can be close to zero. That causes settle time
waiting even for buses that don't use reset during probe.
On my test system this reduces boot time by 1 second if USB enabled, or
by 4 seconds if USB disabled. CAM waited for ctl2cam0 bus "settle".
- Extend the lock to cover xpt_path_release() for the new path.
- While xpt_action() is called while holding right SIM lock for the new
bus, the old path release may require different SIM lock. So we have
to temporary drop the new lock and get the old one.
without holding SIM lock. It really doesn't need that lock, but adding it
removes that specific exception, allowing to assert locking there later.
Submitted by: ken@ (earlier version)
It is required to store extra recovery requests in case of bus resets.
On ATA/SATA this fixes assertion panics on HEAD with INVARIANTS enabled or
possible memory corruptions otherwise if timeout/reset happens when device
CCB queue is already full.
Reported by: gibbs@
MFC after: 1 week
returns zero while request status is not CAM_REQ_CMP. That could cause
partial device attach or other unexpected results.
Found by: Clang Static Analyzer
drivers:
- Remove scsi_low_pisa.*, they were unused.
- Remove <compat/netbsd/physio_proc.h> and calls to the stubs in that
header. They were empty nops.
- Retire sl_xname and use device_get_nameunit() and device_printf() with
the underlying device_t instead.
- Remove unused {ct,ncv,nsp,stg}print() functions.
- Remove empty SOFT_INTR_REQUIRED() macro and the unused sl_irq member.
NetBSD/pc98 was never merged into the main NetBSD tree and is no longer
developed. Adding locking to these drivers would have made the compat
shims hard to impossible to maintain, so remove the shims to ease
future changes.
These changes were verified by md5. Some additional shims can be removed
that do affect the compiled results that I will probably do in another
round.
Approved by: nyan (tentatively)
of this hardware still running (close to twenty years now).
2. Quiesece and use ENC_VLOG instead of ENC_LOG for most
complaints. That is, they're visible with bootverbose, but
otherwise quiesced and not repeatedly spamming messages
with constant reminders that hardware in this space is
rarely fully compliant.
MFC after: 1 month
'encapsulating interface' used with IPsec and has nothing to do with
storage 'enclosure' services.
MFC after: 3 days
Noticed while: debugging why enc(4) is no longer automatically created
It includes three parts:
1) Modifications to CAM to detect media media changes and report them to
disk(9) layer. For modern SATA (and potentially UAS) devices it utilizes
Asynchronous Notification mechanism to receive events from hardware.
Active polling with TEST UNIT READY commands with 3 seconds period is used
for incapable hardware. After that both CD and DA drivers work the same way,
detecting two conditions: "NOT READY: Medium not present" after medium was
detected previously, and "UNIT ATTENTION: Not ready to ready change, medium
may have changed". First one reported to disk(9) as media removal, second
as media insert/change. To reliably receive second event new
AC_UNIT_ATTENTION async added to make UAs broadcasted to all periphs by
generic error handling code in cam_periph_error().
2) Modifications to GEOM core to handle media remove and change events.
Media removal handled by spoiling all consumers attached to the provider.
Media change event also schedules provider retaste after spoiling to probe
new media. New flag G_CF_ORPHAN was added to consumers to reflect that
consumer is in process of destruction. It allows retaste to create new
geom instance of the same class, while previous one is still dying.
3) Modifications to some GEOM classes: DEV -- to report media change
events to devd; VFS -- to handle spoiling same as orphan to prevent
accessing replaced media. PART class already handles spoiling alike to
orphan.
Reviewed by: silence on geom@ and scsi@
Tested by: avg
Sponsored by: iXsystems, Inc. / PC-BSD
MFC after: 2 months
data pointer. This is a temp fix that resubmits the
command, adjusted, so that the backend can fetch the
data again.
Sponsored by: Spectralogic
MFC after: 1 month
Just free inclomplete daemon cache instead to let it retry next time.
Premature ses_softc_cleanup() caused NULL dereference when freed softc
was accessed later.
Renamed the kern.cam.ada.ada_send_ordered sysctl and tunable to
kern.cam.ada.send_ordered, more in line with the other da sysctls/tunables.
Suggested by: kib
kern.cam.da.send_ordered, more in line with the other da sysctls/tunables.
PR: 169765
Submitted by: Steven Hartland <steven.hartland@multiplay.co.uk>
Reviewed by: mav
