to search the QINFIFO to remove any possible command that is waiting
otherwise our abort request may not be held up still waiting for the
first command to complete.
Fix a few panics during error recovery:
1) Stupid mistake in the "no SCB match handler" where I was using the wrong
variable (busy_scbid instead of scb_index).
2) Unbusy the target of an abort request if the command we are trying to
abort is an untagged transaction. If we don't, we get a fatal NO_MATCH_BUSY
condition which "should never happen".
3) When an abort completes, turn off ahc->in_timeout or else the next timeout
will hit the protective "scb timesout again" panic.
4) Fix a typo that caused the requeued "abort" SCB to have its TAG_ENB and
disconnect bits to be cleared (missing ~) so that devices would complain
about overlapped commands.
Be sure to turn off the unexpected busfree interrupt after we do a bus
reset since we are expecting the bus to go free in that case.
Return XS_TIMEOUT instead of XS_DRIVERSTUFFUP in certain scenarios. XS_TIMEOUT
allows for retries, XS_DRIVERSTUFFUP does not.
Allow commands with SDTR and WDTR negotiation to be tagged. The SCSI II spec
says that you probably should not do this for fear of hitting bogus devices.
The driver did this in the past for almost two years without any problem,
and not doing it causes problems during error recovery to a tag capable device
as the number of openings is higher than two and we'll start sending it
tagged commands causing "overlapped commands attempted" type errors. The
real fix needs to happen in the generic SCSI layer which can limit the
number and type of transactions to a device during error recovery efficiently.
Give ourselves at least 100ms to perform a request sense instead of relying
on the original timeout to be long enough to complete this new command as
well as the one that generated the condition.
Removed some redundant code.
with <= 100 usec between each character arrival time. This didn't happen
until rev.1.75 of clock.c because DELAY(100) used to delay for closer to
80 usec than 100 usec, and the minimum time between character arrivals is
87.8 usec at the maximum supported speed of 115200 bps 8N1.
Clear DCD timestamp flag on close (the input timestamp flag is already
cleared).
key "print scrn".
It used to stop at the first non-open vty, now it skips the non-open
ones and thereby enable one to cycle around all open vty by pressing
"print scrn".
I have code to calibrate the overhead fairly accurately, but there
is little point in using it since it is most accurate on machines
where an estimate of 0 works well. On slow machines, the accuracy
of DELAY() has a large variance since it is limited by the resolution
of getit() even if the initial delay is calibrated perfectly.
Use fixed point and long longs to speed up scaling in DELAY().
The old method slowed down a lot when the frequency became variable.
Assume the default frequency for short delays so that the fixed
point calculation can be exact.
Fast scaling is only important for small delays. Scaling is done
after looking at the counter and outside the loop, so it doesn't
decrease accuracy or resolution provided it completes before the
delay is up. The comment in the code is still confused about this.
- don't uselessly initialize the fifo "DMA" bit at attach time.
- initialize the fifo "DMA" bit at open time. Without this, the device
interrupts for every character received, reducing input performance
to that of an 8250.
- don't uselessly initialize the fifo trigger level to 8 (scaled to
256) at attach time.
- don't scale the fifo trigger level to 512 bytes. The driver's pseudo-
dma buffer has size 256, so it can't handle bursts of size 512 or 256.
It should be able to handle the second lowest ftl (2 scaled to 64).
- don't reset the fifos in siostop(). Reset triggers a hardware bug
involving wedging of the output interrupt bit This workaround
unfortunately requires ESP support to be configured.
If we can, use timeouts instead of DELAYs when dealing with a bus reset.
This prevents us from holding up the whole machine for a noticible amount
of time (especially for a real time app).
Make a pass over the timeout/error handling code. Aborts are more
reliable. We actually handle parity errors correctly now instead of
locking up the bus. Added code to properly clean up disconnected SCBs
down on the card during error handling. Improved robustness in several
areas.
If we are using defaults, but are an Ultra card, negotiate at 20MHz instead
of 10.
Don't attempt to handle any commands for 100ms after a reset has occured.
This is the minimum time before a target will respond to selection. Also
disable the busfree interrupt before doing a bus reset. This prevents the
driver from getting confused by an "unexpected busfree".
SEM* and SHM*. These are already supported in the options files. I
mostly used the default value plus 1. This ensures that the LINT kernel
depends on the options headers.
Style nit. Backslashes in macro weren't aligned.
aic7xxx.c:
Preserve the value of STPWEN in SXFRCTL1 during initialization. STPWEN
controls low byte termination and is setup by the PCI probe front end.
Disabling npx0 works right now.
Don't reference `npxdriver' if npx0 is not configured. Not configuring
npx0 doesn't quite work yet.
Don't clear potential non-npx pcb flags in setregs().
should be nearly impossible to overflow the QOUTFIFO (worst case 9 command
have to complete with at least 6 of them requiring paging on an aic7850),
so don't take the additional PIO hit to guard against this condition. If we
don't see our interrupt in time, the system has bigger problems elsewhere.
If this ever does happen, the timeout handler will notice and retry the
command.
Remove the ABORT_TAG sequencer interrupt handler. This condition can't happen
with the new SCB paging scheme.
Fix a few bugs noticed by Dan Eischen <deischen@iworks.InterWorks.org>
that could prevent ULTRA from being negotiated to drives above ID 7 and
also could allow an SCB to be passed to ahc_done twice during error recovery.
Fix a bug notice by Rory Bolt <rory@atBackup.com>. It turns out that a
sequencer reset will actually start the sequencer running regardless of the
state of the pause bit. This could lead to strange problems with loading
the sequencer.
not lazy-fault page table pages. Update the copyout support to take
that into account. This should fix some segfault problems on such
machines.
After a short test period, we'll move this into 2.2.
Submitted by: Stephen McKay <syssgm@devetir.qld.gov.au>
an X seesion. Really stupid error of me, and I've been looking at
this code SO many times. Thanks to Kazutaka YOKOTA for seeing this..
Submitted by: Kazutaka YOKOTA
one in draw_mouse causes spontanious hangs on my p5-100 when I
move the mouse excessively. Forgot that on the last commit, so
using the mouse or destructive cursor would produce large amounts
of flicker..
to -current.
Thanks goes to Ulrike Nitzsche <ulrike@ifw-dresden.de> for giving me
a chance to test this. Only the PCI driver is tested though.
One final patch will follow in a separate commit. This is so that
everything up to here can be dragged into 2.2, if we decide so.
Reviewed by: joerg
Submitted by: Matt Thomas <matt@3am-software.com>
importing it onto a vendor branch first, in the hope that this will
make future maintenance easier.
The conflicts are (hopefully) unimportant. More commits that actually
bring this into the source tree will follow.
Submitted by: Matt Thomas (thomas@lkg.dec.com)
cur_console is NULL when copy_font() is first called from scinit(). This
is apparently harmless when scinit() is called early from sccninit() -
page 0 is apparently mapped r/w then, and 0->status contains suitable
garbage. However, when there is a serial console, scinit() is first
called from scattach() when the page tables are completely initialized,
so the NULL pointer causes a panic.
Submitted by: bruce
called early for console i/o. The timer is usually in BIOS mode
if it isn't explicitly initialized. Then it counts twice as fast
and has a max count of 65535 instead of 11932. The larger count
tended to cause infinite loops for delays of > 20 us. Such delays
are rare. For syscons and kbdio, DELAY() is only called early
enough to matter for ddb input after booting with -d, and the delay
is too small to matter (and too small to be correct) except in the
PC98 case. For pcvt, DELAY() is not used for small delays (pcvt
uses its own broken routine instead of the standard broken one),
but some versions call DELAY() with a large arg when they unnecessarily
initialize the keyboard for doing console output. The problem is
more serious for pcvt because there is always some early console
output.
Guard against the i8254 timer being partially or incorrectly
initialized. This would have prevented the endless loop.
Should be in 2.2.
variable `kern.maxvnodes' which gives much better control over vnode
allocation than EXTRAVNODES (except in -current between 1995/10/28 and
1996/11/12, kern.maxvnodes was read-only and thus useless).
I have no idea if this works since I don't have one of the cards to test.
I also don't know what the LINT and GENERIC entries should look like,
so I just made up some values for now and left them commented out.
Someone who knows the factory settings for a Pro/10, please contact me!
Submitted-By: Javier Martín Rueda <jmrueda@diatel.upm.es>
when allocating memory for network buffers at interrupt time. This is due
to inadequate checking for the new mcl_map. Fixed by merging mb_map and
mcl_map into a single mb_map.
Reviewed by: wollman
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
